Panasonic DMP-BD80 Operating Instructions Manual page 41

Page On the unit's display
j
'--F-9-9----------- re --T--h--e
-~-nit-f~I~-t;-;;;~~-i-;prop;~iY.P;e-s-sTpoWER-C)-1 I-I]-;~the rn~I~-un
--I-t' -t--o--'s-'w"-itch
I
the unit to standby for 3 seconds. Now press [POWER <.!.JIll on the main unit
I
I
again to turn the unit on_ I .
f------------+------------------------t----~
f-H_D_M_I_O_N_L_Y -+_e_S_o_m_e_B_D_-_V_id_e_o_d_i_Sc_s_c_a_n_o_n_IY_be_o_ut_p_u_tw_ith_H_D_M_'_.
~ -_~
NET eDisplays while VIERA CAST is starting up.
I - ,
I
.~
No PLAY eThere is a viewing restriction on a BD-Video or DVD-Video. i 32 :
I - - - - - - - - - - - - + - - - - - - - - - - - - - - - - - - - - . - - - - - - - - - - i - - - - - - - j
No READ eThe media is dirty or badly scratched. The unit cannot play. ! -
I
PLEASE WAIT eThe unit is carrying out internal process. This is not a malfunction. You cannot
II - II
operate the unit while "PLEASE WAIT" is displayed.
'-- -+_e_W_he_n_co_n_n_e_c_te_d_to_T_V_(_V_'_E_R_A_J_W_it_h_H_D_A_V_' c _o_n_t_ro_I_4_,_a_nd_
p
_o_w_e_r_su_
p
_
P
_,y_i_s_t_u_rn_e_d_1
-19
i j ,
.- off by the "Auto power stand-by" function on the TV side. . . .
REMOVE eThe USB device is drawing too much power. Remove the USB device.
SET D eThe remote control and main unit are using different codes. Change the code on 36
(" D " stands for a number.) the remote control.
Press and hold [OK] and the indicated number button at the
same time for more than 5 seconds.
UNFORMAT eYou inserted an unformatted DVD-RAM, DVD-RW, +RW, an unused +R, +R DL
or DVD-RW (DVD-Video formatJ.
UNSUPPORT e You have inserted a media the unit cannot play.
eYou tried to operate with a non-compatible USB device.
6, 7
7
U59
eThe unit is hot.
The unit switches to standby for safety reasons. Wait for about 30 minutes until
the message disappears.
Select a position with good ventilation when installing the unit. Do not block the
cooling fan on the rear of the unit.
U72
U73
eThe HDMI connection acts unusually.
-The connected equipment is not HDM' compatible.
-Please use HDMI cables that have the HDMIIogo (as shown on the coverJ.
-The HDMI cable is damaged.
HDDor FDD eThere is something unusual. (The service number displayed after Hand F
depends on the unit's condition.J
eCheck the unit using the troubleshooting guide. If the service number does not
disappear, do the following.
1 Disconnect the plug from the AC outlet, wait a few seconds, then reconnect it.
2 Press [POWER <.!.J/I] to turn the power on. (The unit may be fixed.J
If the service number does not disappear despite doing the above, request
service from the dealer. Inform the dealer of the service number when requesting
service.
42-44
START eThe system is being restarted during the firmware update. Please do not turn off
power.
16
UPDD/D eThe firmware is being updated.
16
FINISH eThe firmware update is complete.
16
41
ROT9378