Sony CDX-GT320 Operating Instructions Manual page 20

FM/AM
Compact Disc Player
*
AUDIO OUT SUB/REAR
SONY
Installation/Connections
3-215-428-11 (1)
f)
A
e
CDX-GT320/GT32W
Installation/Connexions
*
AUDIO OUT SUB/REAR
B
CDX-GT320/GT32W
BUS AUDIO IN
CDX-GT320
CDX-GT220
CDX-GT120
CDX-GT32W
CDX-GT22W
CDX-GT12W
Source selector*
Selecteur de source*
XA-C40
BUS CONTROL IN
*
not supplied
non fourni
© 2007 Sony Corporation
Printed in China
Notes (iii-A)
• Be sure to connect the ground (earth) lead before connecting
the amplifier.
• The alarm will only sound if the built-in amplifier is used.
Tips
(6-s)
• When connecting only
a
single CO/MO changer or other
optional device, connect directly to this unit.
• For connecting two or more CO/MO changers or other
optional devices, the source selector XA-C40 (not supplied) is
necessary
o
To a metal surface of the car
First connect the black ground (earth) lead, then connect the
yellow and red power supply leads.
e
To the power antenna (aerial) control lead or
power supply lead of antenna (aerial) booster
Notes
• It is not necessary to connect this lead if there is no power
antenna (aerial) or antenna (aerial) booster, or with a
manually-operated telescopic antenna (aerial).
• When your car has a built-in FM/AM antenna (aerial) in
the rear/side glass, see "Notes on the control and power
supply leads."
e
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting any other
system may damage the unit.
o
To the +12 V power terminal which is
energized in the accessory position of the
ignition switch
Notes
• If there is no accessory position, connect to the + 12 V
power (battery) terminal which is energized at all times.
Be sure to connect the black ground (earth) lead to
a
metal surface of the car first.
• When your car has a built-in FM/AM antenna (aerial) in
the rear/side glass, see "Notes on the control and power
supply leads."
o
To the + 12 V power terminal which is
energized at all times
Be sure to connect the black ground (earth) lead to a metal
surface of the car first.
• This unit is designed for negative ground (earth) 12 V
DC operation only.
• Do not get the leads under a screw, or caught in moving
parts (e.g. seat railing).
• Before making connections. turn the car ignition off to
avoid short circuits.
• Connect the
yellow
and
red
power supply leads only
after all other leads have been connected.
• Run all ground (earth) leads to a common
ground (earth) point.
• Be sure to insulate any loose unconnected leads with
electrical tape for safety.
• The use of optical instruments with this product will
increase eye hazard.
Notes on the power supply lead (yellow)
• When connecting this unit in combination with other
stereo components, the connected car circuit's rating
must be higher than the sum of each component's fuse.
• When no car circuits are rated high enough, connect
the unit directly to the battery.
• The numbers in the list are keyed to those in the
instructions.
• The bracket
CD
and the protection collar
@
are
attached to the unit before shipping. Before mounting
the unit, use the release keys
®
to remove the bracket
CD
and the protection collar
@
from the unit. For
details, see "Removing the protection collar and the
bracket (I))" on the reverse side of the sheet.
• Keep the release keys
®
for future use as they
are also necessary if you remove the unit from
your car.
Caution
Handle the bracket
CD
carefully to avoid injuring your
fingers.
x2
®
Power amplifier
Amplificateur de puissance
CD/MD
changer
Changeur de CD/MD
x4
Ed
®
®
Rear speaker
Haut-parleur arriere
Front speaker
Haut-parleur avant
Equipment used in illustrations (not supplied)
Appareils utilises dans les illustrations (non fournis)
D
Catch
Active subwoofer
Caisson de graves actif
Note
Before installing, make sure that the catches on both sides of
the bracket
CD
are bent inwards 2 mm (3/32 in). If the catches are
straight or bent outwards, the unit will not be installed securely
and may spring out.