Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ross DAC-8418-A
Summary of Contents for Ross DAC-8418-A
- Page 1 DAC-8418-A AES to Quad Analog Audio Converter User Manual...
- Page 2 The material in this manual is furnished for informational use only. It is subject to change without notice and should not be construed as commitment by Ross Video Limited. Ross Video Limited assumes no responsibility or liability for errors or inaccuracies that may appear in this manual.
-
Page 3: Important Safety Instructions
Important Regulatory and Safety Notices to Service Personnel Before using this product and nay associated equipment, refer to the “Important Safety Instructions” listed below to avoid personnel injury and to prevent product damage. Product may require specific equipment, and/or installation procedures to be carried out to satisfy certain regulatory compliance requirements. - Page 4 Notice — Changes or modifications to this equipment not expressly approved by Ross Video Limited could void the user’s authority to operate this equipment. CANADA This Class “A”...
- Page 5 The crossed out wheelie bin symbol invites you to use these systems. If you need more information on the collection, resuse, and recycling systems, please contact your local or regional waste administration. You can also contact Ross Video for more information on the environmental performance of our products.
- Page 6 Company Address Ross Video Limited Ross Video Incorporated 8 John Street P.O. Box 880 Iroquois, Ontario, K0E 1K0 Ogdensburg, New York Canada USA 13669-0880 General Business Office: (+1) 613 • 652 • 4886 Fax: (+1) 613 • 652 • 4425 Technical Support: (+1) 613 •...
-
Page 7: Table Of Contents
Before You Begin ........................ 2-2 Static Discharge..................... 2-2 Unpacking......................2-2 Installing the DAC-8418-A ....................2-3 Rear Modules for the DAC-8418-A ..............2-3 Installing a Rear Module ..................2-3 Installing the DAC-8418-A ................... 2-3 Cabling for the DAC-8418-A ....................2-5 DFR-8310 Series Frame Cabling Overview............2-5 DFR-8321 Series Frame Cabling Overview............ - Page 8 • Contents DAC-8418-A User Manual (Iss. 01)
-
Page 9: Introduction
Congratulations on choosing an openGear DAC-8418-A AES to Quad Analog Audio Converter. Your DAC-8418-A is part of a full line of Digital Products within the openGear Terminal Equipment family of products, backed by Ross Video's experience in engineering and design expertise since 1974. -
Page 10: Overview
Overview The DAC-8418-A AES to Quad Analog Audio Converter is a broadcast quality modular product used to convert two channels of 24-bit, unbalanced AES-3id signals to four channels of analog audio. The DAC-8418-A supports audio sampling frequencies from 32kHz to 96kHz. -
Page 11: Functional Block Diagram
Functional Block Diagram This section provides a functional block diagram that outlines the workflow of the DAC-8418-A. AES 1 OUT Reclocker AES 1 IN AES 1 OUT ANLG OUT 1-1 ANLG OUT 1-2 AES 2 OUT Reclocker AES 2 IN... -
Page 12: User Interfaces
4-1. • on using DashBoard, refer to the DashBoard User Manual. Card-edge Controls The front-edge of the DAC-8418-A features LED indicators for the power, video input status and communication activity. For More Information... • on the card-edge controls and LEDs, refer to the chapter “User Controls” on page 3-1. -
Page 13: Documentation Terms And Conventions
“DFR-8300 series frame” refers to all versions of the 10-slot (DFR-8310 series) and 20-slot (DFR-8321 series) frames and any available options unless otherwise noted. • “Frame” refers to DFR-8300 series frame that houses the DAC-8418-A card, as well as any openGear frames. •... - Page 14 1–6 • Introduction DAC-8418-A User Manual (Iss. 01)
-
Page 15: Installation
Installation In This Chapter This chapter provides instructions for installing the Rear Module(s) for the DAC-8418-A, installing the card into the frame, cabling details, and updating the card software. The following topics are discussed: • Before You Begin • Installing the DAC-8418-A •... -
Page 16: Before You Begin
Unpacking Unpack each DAC-8418-A you received from the shipping container and ensure that all items are included. If any items are missing or damaged, contact your sales representative or Ross Video directly. -
Page 17: Installing The Dac-8418-A
Installing the DAC-8418-A This section outlines how to install the DAC-8418-A in a DFR-8300 series frame. If the DAC-8418-A is to be installed in any compatible frame other than a Ross Video product, refer to the frame manufacturer's manual for specific instructions. - Page 18 4. Verify whether your Rear Module Label is self-adhesive by checking the back of the label for a thin wax sheet. You must remove the wax sheet before affixing the label. 5. Affix the supplied Rear Module Label to the BNC area of the Rear Module. 2–4 • Installation DAC-8418-A User Manual (Iss. 01)
-
Page 19: Cabling For The Dac-8418-A
DFR-8300 series frames. Connect the input and output cables according to the following sections. DFR-8310 Series Frame Cabling Overview In the DFR-8310 series frames, the DAC-8418-A is used with the following Rear Module: • 8310AR-036 Rear Module — Each module occupies one slot and accommodates one card. -
Page 20: Software Upgrades For The Dac-8418-A
Software Upgrades for the DAC-8418-A The card can be upgraded in the field via the MFC-8300 series Network Controller card in your frame. Note — DashBoard version 3.0.0 or higher is required for this procedure. To upgrade the software on a card 1. -
Page 21: User Controls
User Controls In This Chapter This chapter provides a general overview of the user controls available on the DAC-8418-A. The following topics are discussed: • Card Overview • Control and Monitoring Features DAC-8418-A User Manual (Iss. 01) User Controls • 3–1... -
Page 22: Card Overview
Card Overview This section provides a general overview of the DAC-8418-A components. For information on the LEDs available on the card-edge, refer to the section “Control and Monitoring Features” on page 3-6. Figure 3.1 DAC-8418-A — Components SW1 — Remote Control Use SW1 to disable remote control of the DAC-8418-A from DashBoard. - Page 23 SW9, SW10 — Output Level Selection SW9 and SW10 are used in conjunction to calibrate the output level (+4dB). Refer to the section “Setting the Nominal Output Level” on page 3-4 for details. DAC-8418-A User Manual (Iss. 01) User Controls • 3–3...
-
Page 24: Configuring The Dip Switches
Configuring the DIP Switches This section provides a brief summary of the DIP Switches of the DAC-8418-A. Refer to Figure 3.1 for the DIP Switch locations. Figure 3.2 shows all the DIP Switches in the OFF position. Figure 3.2 DIP Switches — OFF Position... - Page 25 Table 3.3 Nominal Output Level SW10 Level (dB) DAC-8418-A User Manual (Iss. 01) User Controls • 3–5...
-
Page 26: Control And Monitoring Features
Control and Monitoring Features This section provides information on the LEDs for the DAC-8418-A. Refer to Figure 3.3 for the location of the LEDs. Lock 1 LED No Lock 1 LED Lock 2 LED No Lock 2 LED Card Ejector Figure 3.3 DAC-8418-A Card-edge LEDs... -
Page 27: Dashboard Menus
DashBoard Menus In This Chapter This chapter briefly summarize the menus, items, and parameters available from the DashBoard Control System™ for the DAC-8418-A. Parameters marked with an asterisk (*) are the factory default values. The following topics are discussed: •... -
Page 28: Status Tabs
Card Name AES to Quad Analog Audio Converter Product DAC-8418-A Product Supplier Ross Video Ltd. (Read-only) Serial Number Indicates the serial number of the board Software Rev ##.## Indicates the software version 4–2 • DashBoard Menus DAC-8418-A User Manual (Iss. 01) -
Page 29: Dac Output Tabs
STEREO Gain Control 0 to 100 Calibrates the analog output level of the card. CH# Trim Control (dB) -15 to 15 Note that this setting overrides the value set by SW9 and SW10. DAC-8418-A User Manual (Iss. 01) DashBoard Menus • 4–3... - Page 30 4–4 • DashBoard Menus DAC-8418-A User Manual (Iss. 01)
-
Page 31: Specifications
Specifications In This Chapter This chapter provides technical specifications on the DAC-8418-A. Note that technical specifications are subject to change without notice. The following topics are discussed: • Technical Specifications DAC-8418-A User Manual (Iss. 01) Specifications • 5–1... -
Page 32: Technical Specifications
Technical Specifications This section provides technical information for the DAC-8418-A. Table 5.1 DAC-8418-A Technical Specifications Category Parameter Specification Number of Inputs 2 AES Resolution 24Bit AES/EBU Digital Input Level 0.2-7V p-p Inputs Impedance 75ohm Sampling Frequency Range 32kHz to 96kHz... -
Page 33: Service Information
Service Information In This Chapter This chapter contains the following sections: • Troubleshooting Checklist • Warranty and Repair Policy DAC-8418-A User Manual (Iss. 01) Service Information • 6–1... -
Page 34: Troubleshooting Checklist
Routine maintenance to this openGear product is not required. In the event of problems with your DAC-8418-A, the following basic troubleshooting checklist may help identify the source of the problem. If the frame still does not appear to be working properly after checking all possible causes, please contact your openGear products distributor, or the Technical Support department at the numbers listed under the “Contact Us”... -
Page 35: Warranty And Repair Policy
FIVE (5) years from the date of shipment from our factory. In the event that your DAC-8418-A proves to be defective in any way during this warranty period, Ross Video Limited reserves the right to repair or replace this piece of equipment with a unit of equal or superior performance characteristics. - Page 36 Contact Us Contact our friendly and professional support representatives for the following: • Name and address of your local dealer • Product information and pricing • Technical support • Upcoming trade show information Telephone: +1 613 • 652 • 4886 Technical After Hours Emergency: +1 613 •...
Need help?
Do you have a question about the DAC-8418-A and is the answer not in the manual?
Questions and answers