Related Manuals for Husqvarna 225E
Summary of Contents for Husqvarna 225E
- Page 1 225E Operator’s manual Read through the Operator‘s manual carefully and understand the content before using the machine. (CARB, EPA) 101 89 19-95...
-
Page 2: Symbol Explanation
Symbols WARNING! The edger can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. Read through the Operator‘s Manual carefully and understand the content before using the machine. Always use • A protective helmet where there is a risk of falling objects •... -
Page 3: Table Of Contents
Angle gear ... 19 Lubricating the flexible drive axle ... 19 Adjusting the edger‘s cutting depth ... 19 Maintenance schedule ... 20 TECHNICAL DATA 225E ... 21 FEDERAL AND CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT Your warranty rights and obligations ... 22 English –... -
Page 4: Safety Instructions
Personal protective equipment IMPORTANT INFORMATION • An edger used incorrectly or carelessly can become a dangerous tool, that can cause serious or fatal injury to the operator or others. It is extremely important that you read and understand the content of this manual. •... - Page 5 4. Vibration damping system Your machine is equipped with a vibration damping system, which is designed to give as vibration-free and comfortable use as possible. The use of incorrect cutting equipment increases the level of vibration. The machine‘s vibration damping system reduces the transfer of vibrations between the engine unit/ cutting equip- ment and the machine‘s...
-
Page 6: Control, Maintenance And Service Of The Machine's Safety Equipment
Control, maintenance and service of the machine‘s safety equipment IMPORTANT INFORMATION • All service and repairs to the machine require special training. • This applies especially to the machine‘s safety equip- ment. If the machine does not meet any of the controls listed below you should contact your service work- shop. -
Page 7: Cutting Equipment
6. Cutting equipment Two basic rules: 1) Only use the cutting and guard equipment we recommend! See chapter “Technical data“. 2) Check the cutting equip- ment with regard to damage and crack formation. Damaged cutting equipment should always be replaced. WARNING! Always stop the engine before starting work on any part of the cutting equipment. -
Page 8: General Safety Instructions
General safety instructions IMPORTANT INFORMATION • The machine is only designed for cutting the edges of lawns. • The only accessories to be used with the engine unit as a drive source are the cutting units we recommend in the chapter “Technical data“ . •... -
Page 9: Transport And Storage
Start WARNING! When the engine starts with the choke lever in the choke or starter throttle position the cutting tool (blade or trimmer) starts to rotate immediately. • The complete clutch cover with shaft must be fitted before the machine is started,... -
Page 10: General Working Instructions
General working instructions IMPORTANT INFORMATION • This section takes up the basic safety precautions for working with the edger. • If you encounter a situation where you are uncertain how to proceed you should ask an expert. Contact your dealer or your service workshop. •... - Page 11 Safety instructions after completing work • Ensure the blade has stopped before cleaning, carrying out repairs or an inspection. Remove the spark plug cable from the spark plug. • Wear heavy-duty gloves when carrying out repairs on the edger. • Store the machine out of reach of children.
-
Page 12: What Is What
What is what on the edger? Blade Grease filler cap Angle gear Blade guard Shaft Loop handlebar Throttle Stop switch Throttle trigger lock 10. Suspension for harness 11. Cylinder cover 12. Starter handle 13. Fuel tank 14. Choke – English WHAT IS WHAT? 15. -
Page 13: Assembly
Assembling the loop handlebar • Unscrew the handle and plastic cover from the handlebar bracket. • Place the loop handlebar with the handlebar holder on the handlebar bracket. Fit the handle and plastic cover. Do not tighten too tight. Assembling the angle gear •... -
Page 14: Fuel Handling
• When working at continuous high revs a higher octane rating is recommended. Two-stroke oil • For the best results use HUSQVARNA two-stroke oil, which has been specially developed for two-stroke engines. Mixing ratio 1:50 (2%). • Never use two-stroke oil... -
Page 15: Start And Stop
WARNING! When the engine starts with the choke lever in the choke or starter throttle position the cutting tool (blade or trimmer) starts to rotate immediately. Start Press the machine body against the ground using your left hand (NOTE! Do not use your foot). -
Page 16: Maintenance
Carburetor Your Husqvarna product has been designed and manufac- tured to specifications that reduce harmful emissions. After your unit has been run 8-10 tanks of fuel the engine has broken in. To ensure that your unit is at peak perfor-... - Page 17 Final setting of the idling speed T Adjust the idling speed with the screw T, if it is necessary to readjust. First turn the idle speed adjusting screw T clockwise until the cutting attachment starts to rotate/ move. Then turn, counter-clockwise until the cutting attachment stops.
-
Page 18: Muffler With Catalytic Converter
Muffler with catalytic converter A muffler fitted with a catalytic converter reduces the extent of the following substances in the exhaust fumes: • Hydrocarbons (HC). Some hydrocarbons in gasoline and the exhaust are carcinogenic. • Nitric oxides (NO). Irritating for the breathing air-ways. •... -
Page 19: Spark Plug
However, before using the machine you should check that the angle gear is filled to 3/4 with grease. Use HUSQVARNA special grease. Normally, the grease does not need to be changed except when repairs are carried out. MAINTENANCE Lubricating the flexible drive axle Inside the edger‘s drive shaft... -
Page 20: Maintenance Schedule
NOTE: Use only HUSQVARNA replacement parts. Use of other brands of replacement parts can cause damage to your unit or injury to the operator or others. Your warranty does not cover damage or liability caused by the use of accessories and/or attachments not specifically recommended by HUSQVARNA. -
Page 21: Technical Data
Vibration levels on the handles measured according to prEN 31806 and ISO 7916, m/s Blade, idling rear/front handles: Blade max. speed rear/front handles: Cutting equipment Blade Blade guard TECHNICAL DATA 225E 1,55/25,4 1,34/34 1,10/28 11 000-12 000 14 000 2.700 10 000 0,9 kW/9.000 rpm... -
Page 22: Federal And California Emission Control Warranty Statement
REPAIR OR REPLACEMENT OF PARTS Repair or replacement of any warranted part will be performed at no charge to the owner at an approved Husqvarna Forest & Garden servicing dealer. If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized servicing dealer or call Husqvarna Forest &... - Page 23 NOTES English –...
- Page 24 ´*2{•¶5$¨ – English...