Standard Features And Accessories; Indoor Unit Accessories - Carrier 40KMC Product Data

STANDARD FEATURES AND ACCESSORIES

Ease Of Installation
Indoor and Outdoor Compact Size
Outdoor Unit Wall Mounting Kit
Outdoor Unit Stacking Kit
Built --- in Condensate Pump
Comfort Features
Microprocessor Controls
Automatic Air Sweep
Air Direction Control
Auto Restart Function
Cold Blow Protection On Heat Pumps
Air Stratification Compensation
Emergency Run Mode
Auto Changeover on Heat Pumps
Energy Saving Features
Sleep Mode
Stop/Start Timer
Safety And Reliability
3 Minute Time Delay For Compressor
Over Current Protection For Compressor
Crankcase Heater (standard on 38QRF--- 030,035)
High and Low Pressure Switches on Cooling Only Units
High Pressure Switch and Loss of Charge Switch on Heat
Pump
Indoor Coil Freeze Protection
Indoor Coil High Temperature Protection On Heat Pumps
Condenser High Temperature Protection On Heat Pumps
Accumulator On Cooling Only and Heat Pumps
Ease Of Service And Maintenance
Control Box Accessible From Bottom of Unit
Cleanable Filters
Diagnostics
Test Mode
Liquid Line Pressure Taps
Suction And Discharge Pressure Taps
Application Flexibility
208/230 and 460 3 Phase on Size 035 and 036
Long Lines up to 200 feet (61 m) (accessories required)
Power Ventilation Kit
Low Ambient Controls (--- 20° F / --- 28.9° C)
Knock--- out to run a duct from an adjacent room
Wind Baffles
Wired or Wireless Controls
Zone Manager
Warranty
5 --- Year Compressor Warranty
1 --- Year Parts Warranty
Compressor Extended Warranty Years 6 Thru 10
All Parts And Labor Years 2 Thru 5
All Parts And Labor Years 2 Thru 5,
Compressor Years 6 Thru 10
Legend
S Standard
A Accessory
O Optional

INDOOR UNIT ACCESSORIES

Grille
To maximize shipping efficiency, the grille for the in- -ceiling
cassette is set up as an accessory.
Air Supply Outlet Obstruction Kit
This kit can be used when up to two discharge outlets need to be
blocked in applications where the unit is installed close to a wall or
a corner.
Power Ventilation Kit
S
This kit will allow up to 20% of outside air to be introduced into
A
the conditioned space.
A
S 4" FLEX DUCT
S
S
S
S
S
S
S
S
AIRFLOW
S
S
Fig. 1 – Power Ventilation Kit
S
Remote Control (33MC- -UMC)
S
To provide added flexibility of choosing the user interface method
A
S
with the unit, a remote control or wired controller can be ordered.
Remote Control Locking Mount Kit
S
This kit can be used where there is a concern that the remote
S
control can be misplaced. This accessory locks the remote in place.
S
S
Wired Controller (33MC- -URC)
S
For applications where the use of a wireless remote control is not
desired, the 40KMC/KMQ units can be controlled by means of a
S
wired , wall- -mounted control with an LCD display.
S
S
S
S
S
S
A
A
A
A
Fig. 2 – Wall Mounted Control with LCD Display
A
A
Room Control Wiring Kit (33MC9005)
A
Up to six units can be daisy- -chained together and controlled by
one wired remote controller. A room control wiring kit is required
S
for each slave unit.
S
O
Zone Manager (33MC- -UZM)
O
For applications where more sophisticated controls are required, a
O
Zone Manager that permits the connection of up to 32 different
indoor units, divided into a maximum of eight different zones, can
be used. Zone Manager Wiring Kit (33MC9004) is required to
connect different units to the zone manager.
ZONE 1
ZONE ..
Remote Control
ZONE 8
Fig. 3 – Zone Manager Connection
4
WEATHERPROOF
INSULATED
INSULATED
FUSED DISCONNECT
SUCTION LINE
LIQUID LINE
PER NEC
4" FLEX DUCT
Zone Manager
POWER
VENTILATION
ACCESSORY
POWER
VENTILATION
A07268
A08432
A08443