Download  Print this page

Westinghouse WDF901SA Installation Manual

Built under & free standing dishwashers
Hide thumbs
   

Advertisement

Quick Links

Dimension anD insTallaTion guiDe
moDels:
WDF901SA, WDF901WA, WDF902SA, WDF902WA
IMPORTANT
• T hese instructions are a guide only. For complete installation
instructions, refer to the manual provided with the product.
• I f you do not follow the installation instructions your
dishwasher will not be properly installed. The product
warranty does not cover incomplete or improper
installation. You will be charged a service fee for any
service call to rectify improper or incomplete installation.
• T hese instructions apply to freestanding applications only.
• I f your dishwasher is fitted with a water inlet hose with safety
valve, you will need an opening of at least 45mm x 90mm
in your cupboards in order to feed the hose through it.
Dishwasher Dimensions
The dimensions shown below are in millimetres. The height of
850mm is with the levelling legs screwed in at the minimum height.
centre of
control
panel
100mm
596mm
CupboarD opening Dimensions
The dimensions shown below are in millimetres. The opening
There should be a minimum
allows for some clearance so that the dishwasher can be
2mm gap between the top of
the dishwasher and
pushed into place.
underside of bench top
Note: if the opening is greater than 600mm wide then a
suitable width filler piece should be secured to the cupboard
before installing the dishwasher.
should be equal and no greater
620mm
850mm
820mm
180mm
50mm
555mm edge of door
585mm centre of door
The hose should not be
extended by more than
2 metres or water pump-out
problems may occur
DISHWASHER
Gap on both sides
than 3mm per side
If floor is not level, adjust
levelling legs to suit
Remove entire plastic
built under & free standing dishwashers
FiTTing unDer a CounTer
Put the appliance adjacent to a water tap and a water drain.
The plinth of a freestanding appliance is not adjustable. Do
not remove the appliance's worktop if you want to use it as
a freestanding unit. It is not necessary to remove the worktop
when installing under a standard kitchen bench top. Only
remove the appliance worktop to install under a close fitting
sink unit or kitchen worktop (820mm).
Make sure that the dimensions of the recess agree with the
given dimensions.
removing The applianCe workTop
1. Remove the rear screws.
2. Pull the worktop behind the appliance.
3. Lift the worktop and move it from the front slots.
Fix drain hose max of
4. Level off the appliance using the adjustable feet.
10mm below the top of
5. Install the appliance under the kitchen worktop ensuring that
the dishwasher
water hoses are not kinked or squashed.
The appliance must be easily accessible to a technician if
repair is necessary.
SINK
600mm max -
300mm min
1000mm max
POWER OUTLET
POWER SUPPLY
230/240V–10Amps
Remove entire plastic
membrane from sink trap
spigot & fit drain hose to
spigot with clamp
TAP CONNECTION
If cold-water pressure is
in excess of 800kPa, a
pressure-reducing valve
should be used.
Check for leaks.
INLET WATER SUPPLY
Water flow rate 10L/minute min
o
Water temperature 60
C max
Water pressure cold water:
800kPa max - 50kPa min
Water pressure hot water:
350kPa max - 50kPa min
Cold water recommended
1

Advertisement

loading

  Summary of Contents for Westinghouse WDF901SA

  • Page 1 Dimension anD insTallaTion guiDe built under & free standing dishwashers moDels: WDF901SA, WDF901WA, WDF902SA, WDF902WA FiTTing unDer a CounTer IMPORTANT Put the appliance adjacent to a water tap and a water drain. The plinth of a freestanding appliance is not adjustable. Do • T hese instructions are a guide only. For complete installation not remove the appliance’s worktop if you want to use it as instructions, refer to the manual provided with the product. a freestanding unit. It is not necessary to remove the worktop • I f you do not follow the installation instructions your when installing under a standard kitchen bench top. Only dishwasher will not be properly installed. The product remove the appliance worktop to install under a close fitting warranty does not cover incomplete or improper sink unit or kitchen worktop (820mm). installation. You will be charged a service fee for any Make sure that the dimensions of the recess agree with the service call to rectify improper or incomplete installation.
  • Page 2 180mm 100mm 50mm 595mm 555mm edge of door 120mm 585mm centre of door TypiCal builT-unDer insTallaTion Remove entire plastic There should be a minimum The hose should not be Fix drain hose max of membrane from sink trap 2mm gap between the top of extended by more than 10mm below the top of spigot &...
  • Page 3 • E nsure that the dishwasher has been tested using the rinse • A fter connecting hose to the tap, turn the tap on and & hold or quick 30 cycle and that the dishwasher fills with check to ensure that there are no leaks. water, washes and drains with no leaks. The manufacturer accepts no liability for failure to observe the above safety precautions. For further information on all Westinghouse appliances, call into your Retailer, phone our Customer Care centre on 1300 363 640 or visit www.westinghouse.com.au © Copyright 2009 Electrolux Home Products Pty Ltd ABN 51 004 762 341 WDIM_DISH901902_ Jul09...

This manual is also suitable for:

Wdf901waWdf902saWdf902wa