Lionel SD60-M Owner's Manual
  1. Manuals
  2. Brands
  3. Lionel Manuals
  4. Toy
  5. SD60-M
  6. Owner's manual
Lionel SD60-M Owner's Manual

Lionel SD60-M Owner's Manual

Diesel locomotive
Hide thumbs Also See for SD60-M:
Table of Contents

Advertisement

Quick Links

Download this manual
71-8232-250
09/97
SD60-M
diesel locomotive
Owner's Manual
featuring
and

Advertisement

Table of Contents
loading

Related Manuals for Lionel SD60-M

Summary of Contents for Lionel SD60-M

  • Page 1 71-8232-250 09/97 SD60-M diesel locomotive Owner’s Manual featuring...

  • Page 2: Table Of Contents

    • Magne-Traction (in command mode) Table of contents Transformer operations Running your Lionel SD60-M with a Lionel transformer Locking your SD60-M into a single operational state Using your SD60-M’s Electrocoupler Plus couplers Your SD60-M’s Railsounds system—the basics Experiencing the range of your SD60-M’s Railsounds system Notes on Railsounds Installing the Lionel no.

  • Page 3: Transformer Operations

    WITH DIRECT CURRENT sitive electronic components may occur. • When you first power up your track, the SD60-M will wait between 3 and 8 seconds as it “listens” for digital language from the TrainMaster Command Base (available separately). When it’s determined that it’s on a conventional (nonCommand) railroad, the SD60-M’s headlight will illuminate and...

  • Page 4: Locking Your Sd60-M Into A Single Operational State

    Transformer operations Locking your SD60-M into a single operational state without stopping. Set the reverse unit o select a single operational state for control switch to PROGRAM/LOCK. your Lionel SD60-M (example: for- The SD60-M is now “locked” into your ward only), you can deactivate the chosen direction.

  • Page 5: Your Sd60-M's Railsounds

    Slide open the (horn and bell access panel as remain unaf- Install a 9-volt alkaline battery in your SD60-M . shown in the fected), slide illustration. Connect the 9-volt alkaline the Railsounds switch, located under- battery to the battery clip, and place...

  • Page 6: Experiencing The Range Of Your Sd60-M's Railsounds System

    Transformer operations Experiencing the range of your SD60-M’s Railsounds system Now, decrease track voltage to the ith Railsounds, you experience desired speed level, press DIR on your the sounds of real railroading CAB-1 remote or transformer, and like never before. Simply put, it’s the...

  • Page 7: Installing The Lionel No. 610-5906-001 Sound Activation Button

    (for bell) (for horn) The no. 610-5906-001 sound activation button (available separately) works with any Lionel AC transformer except no. 6-4690 Type MW. Note! Transformers made by other manufacturers may not be compatible with Railsounds.

  • Page 8: Trainmaster Command Tm

    • All Command-equipped Lionels come factory-programmed with an ID# of “1.” To change your SD60-M’s ID#, see page 12. Move ‘em out! • Throttle up or press any command button on CAB-1. Your SD60-M will respond to your every command. Read on. The fun is just beginning!

  • Page 9: Running Your Sd60-M In The Trainmaster Command Environment

    Command-equipped SD60-M Example address Locomotive #1 comes factory-programmed with an ID# of “1.” To get your SD60-M in PowerMasters set to CMD or traditional action, set PowerMasters to CMD or power supplies ON FULL set all power supplies on full. Press ENG and “1”...

  • Page 10: Cab-1 Numeric Keypad Commands For Your Sd60-M

    TARTUP SEQUENCE COMMENCES Lowers the volume of Rail- Turns strobe light off. sounds. S OUND VOLUME DECREASES Activates the Railsounds shut- Turns strobe light on. down sequence. Just like the real thing, your SD60-M’s RPMs must be at idle...

  • Page 11: Tuning Your Sd60-M's Performance

    “stall” voltage. Get mand environment gives you a bonus your locomotive moving, then press Railsounds effect—the ultrarealistic SET; the SD60-M will stop. Turn the sound of squealing brakes. throttle clockwise to get the locomotive moving, then decrease speed until the SOUND QUALITY locomotive just stops.

  • Page 12: Assigning Your Sd60-M A New Id

    SD60-M’s cab number. Command Base ON Turn the Command Base ON and Place the SD60-M on track place the SD60-M on track. Power up, PowerMasters set to CMD or then set the SD60-M’s reverse unit con- traditional power supplies ON FULL trol switch to PROGRAM/LOCK (see the illustration).

  • Page 13: Maintaining And Servicing Your Sd60-M

    Maintaining and servicing your SD60-M Lubricating your SD60-M grease or oil on the SD60-M’s wheels or elp your Lionel SD60-M lead a your track. long and productive life on your You’ll know your SD60-M requires railroad by maintaining it properly.

  • Page 14: Lubricating Your Sd60-M's Pullmor

    @@ @@ @@ @@ yy yy 2 cab screws After removing the .050" set screw, place a small amount of Lionel oil (two drops maximum) in the set screw hole. Reinstall the set screw tightly, then back off one-half turn.
  • Page 15 Press Aux2 to make sure headlamp was not accidently turned off, Note! before replacing bulb Your Lionel SD60-M is equipped with a roof mounted flashing strobe light, this small bulb (Lionel part no. 10-8803-009) is located inside the cab. During the course of normal operation it may require Note! replacement.

  • Page 16: Lionel Service

    Lionel while at Lionel. You may choose to have your and carries a limited warranty to support product repaired by one of our authorized continued reliable operation. If service is...

This manual is also suitable for:

Sd60-m 71-8232-250

Table of Contents