Crestron CAPTURE-HD Quick Start Manual

CAPTURE-HD & CAPTURE-HD-PRO
1
Included Items
The following items are included with the CAPTURE-HD and
CAPTURE-HD-PRO: (herein known as Capture recorder):
• One Multimedia Memory Card, SDHC™ (16 GB)
• One power pack: 12 volt dc Power Pack, Universal,
(removable power cord included)
• One BNC to RCA adapter
• One 3-pin and two 5-pin single row interface connectors
• Two rack mount brackets
• Eight screws to attach rack mount brackets
• One 3-foot (~0.9 meter) stereo audio cable with RCA connectors
The following items are available separately:
®
• CAM-IFB-100, Camera for Capture HD
• CAM-IPTZ-101, PTZ Camera for Capture HD
• CAPTURE-TPMC-4SM, Touch Screen Controller for CAPTURE-HD
• CBL Series, Crestron ® Certified Interface Cables
• CEN-FUSION-RVS-R310 Pre-configured Fusion RV
• Fusion RV (SW-FUSION-RV) Remote Asset Management Software
• MP-FS100_PAK, FreeSpeech ® Single-Channel Wireless Mic System Package
• MP-FS200_PAK, FreeSpeech Dual-Channel Wireless Mic System Package
2
Initial Hookup
1. Insert the included SDHC card into the MEMORY slot, contacts facing
down.
2. If the installation requires connection to a network, plug a network cable
into the LAN port.
3. Connect the G (ground) terminal to earth ground.
4. Connect the supplied power supply to the 12V 5.0A port.
NOTE: Do not apply power at this time.
Memory
Card LAN
1
For details, refer to the CAPTURE-HD & CAPTURE-HD-PRO
Operations Guide, Doc. 7233.
QUICKSTART DOC. 7234E (2031322)
Capture HD ® High-Definition Capture Recorder
3 Connect Speech Input
Connect the output of the microphone system to one of the SPEECH IN
connectors. (The RCA jack provides for unbalanced input; the 3-pin
connector provides for balanced input. Use only one input at a time.)
Crestron recommends using the FreeSpeech wireless mic system. To do
so, simply connect an RCA cable from the white LINE OUT connector on
the rear of the FreeSpeech receiver to the white unbalanced input
connector on the Capture recorder.
Unbalanced
Input
4
Connect Camera
Connect the camera using the CAMERA IN COMPOSITE or 3G-SDI input.
(The 3G-SDI input is available only on the CAPTURE-HD-PRO.)
A BNC to RCA adaptor is included for use with the COMPOSITE input, if
needed.
® Server System
The Capture recorder is pre-configured to select the 3G-SDI source, if
present, otherwise it selects the COMPOSITE input.
Crestron recommends the following two Crestron composite cameras:
CAM-IFB-100
(Sony model SNC-CH110)
DC
Power Ground
www.crestron.com
07.13
Specifications subject to
change without notice.
Balanced
Input
MP-FS-RX1 FreeSpeech System
CAPTURE-HD-PRO Only
CAM-IPTZ-101
(Canon model VB-C300)*
* The camera is supplied with an 8" (203 mm)
3.5 mm monaural to female BNC adapter cable.
888.273.7876 201.767.3400
5
Connect Content Source
Connect the content source (typically a PC or laptop) to one of the CONTENT IN
inputs on the Capture recorder. Both HDMI and RGBHV (VGA) are provided.
The Capture recorder is pre-configured to automatically select the HDMI
if present, otherwise it selects the RGBHV source.
6
Connect Output
Connect the output. The LOOP OUT RGBHV port can be used to route the content
from the RGBHV input directly to a display or projector, allowing the Capture
recorder to fit into an existing system seamlessly.
Projector
Typical Image on RGBHV or HDMI Output
Typical PIP Image on HDMI Output
The HDMI OUT port can also be used to display
the selected content input source.
It can also be configured to act as a "confidence
monitor" showing exactly what is being recorded.
7
Connect Power
Plug the power supply line cord into a standard 110 -120 Vac power source. The
Capture recorder goes through an initialization sequence that takes approximately
90 seconds. When the initialization process is complete, the front panel display is
similar to the following:
Press REC when ready
2013-03-13 16:25
No meetings
® source,
Content
Only
Content
Camera