Related Manuals for Savoy 42-830-5RV-187
Summary of Contents for Savoy 42-830-5RV-187
-
Page 1: Ceiling Fan
CEILING FAN OWNER'S MANUAL READ AND SAVE THESE INSTRUCTIONS MODEL: 42-830-5RV-187 42-830-5RV-129 FAN RATING AC 120V. 60Hz CUL LISTED MODEL : AC-542... -
Page 2: Tools And Materials Required
1. TOOLS AND MATERIALS REQUIRED Philips screw driver Blade screw driver 11 mm wrench Step ladder Wire cutters 2. PACKAGE CONTENTS Unpack your fan and check the contents. You should have the following items; a. Set of blades assembly (5) b. -
Page 3: Safety Rules
3. SAFETY RULES 1. To reduce the risk of electric shock, 7. Do not operate reversing switch while insure electricity has been turned off fan blades are in motion. Fan must be at the circuit breaker or fuse box turned off and blades stopped before before beginning. -
Page 4: Mounting Options
4. MOUNTING OPTIONS If there isn't an existing CUL listed mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers. Outlet box Secure the outlet box directly to the building structure. appropriate fasteners and building materials. -
Page 5: Hanging The Fan
5. HANGING THE FAN REMEMBER to turn off the power. Follow the steps below to hang your fan properly. CUL Listed electrical box NOTE: This ceiling fan is supplied with two Hanger types of hanging assemblies; the standard bracket ceiling installation using the downrod with ball and socket mounting and the Mounting screws "close-to-ceiling"... - Page 6 CLOSE-TO-CEILING INSTALLATION 1. Pass the 120-volt supply wires through Canopy the center hole in the ceiling hanger bracket as shown in Fig. 5. Decorative canopy cover Figure 8 2. Remove the decorative canopy cover from the canopy. (Fig. 8) 3. Secure the hanger bracket to the ceiling Screw and lockwasher (3 of 6 places) outlet box with the screws and washers...
-
Page 7: Installation Of Safety Support
6. INSTALLATION OF SAFETY SUPPORT An additional safety support is provided to Hanger bracket Safety cable prevent the fan from falling. Secure the safety cable to the ceiling joist with screw and washer, as illustrated in Figure 11. Figure 11 7. -
Page 8: Finishing The Installation
NOTE: LIGHT KITS ARE AVAILABLE AT YOU POWER LINES 120V SAVOY HOUSE RETAILER. THE FAN IS ALREADY WIRED TO SUPPORT THE LIGHT GREEN GROUND KIT OPTION. WIRING LIGHT WARNING: TO REDUCE THE RISK OF FIRE, GROUND TO MOUNTING ELECTRIC SHOCK, OR OTHER PERSONAL... -
Page 9: Attaching The Fan Blades
9. ATTACHING THE FAN BLADES Caution: Remove 5 rubber packing mounts and discard before installation. Step 1. Attach the blade to the blade bracket using the screws and rubber washers as shown in Figure 17. Start screw into bracket. Repeat for the two remaining screws. -
Page 10: Installing The Switch Housing
11. INSTALLING THE SWITCH HOUSING NOTE: Before starting installation, disconnect the power by turning off the circuit breaker or removing the fuse at fuse box. Turning power off using the fan switch is not sufficient to prevent electric shock. Step 1. Remove the screws from the mounting plate under the fan motor. -
Page 11: Operating Your Fan
12. OPERATING YOUR FAN NOTE: Wait for fan to stop before changing the setting of the slide switch. Turn on the power and check the operation of your fan. The pull chain controls the fan speed as follows: 1 pull- High, 2 pulls-Medium, 3 pulls- Low, and 4 pulls-Off. -
Page 12: Troubleshooting
13. TROUBLESHOOTING Problem Solution Fan will not start. 1.Check circuit fuses or breakers. 2. Check line wire connections to the fan and switch wire connections in the switch housing. CAUTION: Make sure main power is off. Fan sounds 1. Make sure all motor housing screws are snug. noisy.