Restoring Keymoved Keys To Default; Settings; Restoring A Single Keymoved Key; Restoring All Keymoved Keys In A - One for All 6-Device Universal Remote User Manual

O F A 6 U
NE OR LL
5. For the destination mode, press
VCR once.
6. For the destination key, press
VOL + once.
7. The LED will blink twice,
indicating the keymoved
sequence is correct.
8. Repeat steps 1 through 7 twice
more to map remaining volume
control keys, substituting VOL -
and MUTE as source and
destination keys in steps 4 and 6.
Upon completion of the above
procedure, you can now use your One
For All 6L Universal Remote Control
(URC-6020 B00) to control the TV's
volume and MUTE in the VCR mode,
as well as in the TV mode.
R K
ESTORING EYMOVED
D S
EFAULT ETTINGS

Restoring a Single Keymoved Key

1. Press a device key that has a
keymoved key.
2. Press and hold SET until the LED
(red light) blinks twice, then
release SET.
Enter 9 9 4. The LED will blink
3.
twice.
4. Press the destination key twice
(where the keymoved key is
stored). The LED will blink
twice.

Restoring All Keymoved Keys in a

Single Mode

Press and hold SET until the LED
1.
(red light) blinks twice, then
release SET.
2. Enter 9 9 4. The LED will blink
twice.
3. Press the destination mode
twice (where keymoved keys are
stored). The LED will blink
twice.
CHANGING VOLUME
LOCK
The One For All 6L Universal Remote
Control (URC-6020 B00) is set at the
factory for independent volume
control of each selected device.
However, you may change the Volume
Lock setting to Global Volume Lock so
that a device's volume will be locked
to one mode (e.g., to control TV
12

Changing Volume Lock

R
NIVERSAL EMOTE
K
EYS TO
C
ONTROL
volume in all other modes). After
that, if desired, you can perform
Individual Volume Unlock on a
selected device to set its volume
control for independent operation.
L V
OCKING OLUME
M
ODE
(G V
LOBAL OLUME
1. Press and hold SET until the LED
(red light) blinks twice, then
release SET.
Enter 9 9 3 and then press any
2.
mode key once (e.g., TV). The
LED will blink twice.
3. Now, when you press VOL +, VOL
-, or MUTE, the volume of the
selected device (e.g., TV) will be
controlled regardless of the
mode you have selected.
U V
NLOCKING OLUME
S D
INGLE EVICE
U )
NLOCK
1. After performing Global Volume
Lock (see left), press a desired
mode key where you want
volume to be unlocked (e.g.,
AUD) and controlled within its
own mode.
2. Press and hold SET until the LED
(red light) blinks twice, then
release SET.
Enter 9 9 3 and then press VOL -
3.
once. The LED will blink four
times.
4. If desired, repeat steps 1 through
3 (of this section) for each
device that you want volume to
be unlocked.
5. Now, after you select a device
that has volume unlocked (e.g.,
AUD), pressing VOL +, VOL -, or
MUTE, will control the device's
volume only in its own mode.
U A
NLOCKING
(
R D
ESTORING
NOTE: Performing these instructions
will restore independent volume
control for all programmed devices
(e.g., TV volume control in TV mode,
VCR volume in VCR mode, etc.).
1. On the remote control, press and
hold SET until the LED (red
light) blinks twice, then release
SET.
C
ONTROL TO
L )
OCK
C
ONTROL FOR A
(I V
NDIVIDUAL
V C
LL OLUME ONTROL
S
EFAULT ETTING
O
NE
OLUME
)