5.15 Setting the Delay Time of Transmitting the Alarm………………………………………………………40 5.16 Setting the Alarm Time for Audible Alarm……………………………………………………………………41 5.17 Miscellaneous Settings………………………………………………………………………………………………….41 6. Digital Communication Standard – Contact ID Protocol for WT-1010C2…………………………….44 7. Technical Specifications....................47 WT1010C2 – USER MANUAL – Rev.2.7 – Technical Support : Technical@witura.com...
WT-1010C2 USER MANUAL 1. Introduction to the WT-1010C2 GSM Alarm System The WT 1010C2 GSM Terminal is a wireless communicator for alarm and fire panels that uses the cell phone network (GSM) to transmit alarms and other panel event. The module checks the status of the PSTN line and in case the PSTN line becomes unavailable, the WT 1010C2 GSM emulate the line signal to the panel.
WT-1010C2 uses the telephone line as the main transmission line and uses the GSM voice channel as backup 4. The WT-1010C2 unit can continuously watches if a Contact ID is directed towards the security monitoring station through the wired or GSM network, and if either of the preset report codes is noticed, it sends an appropriate SMS message with definable text to a mobile phone numbers.
3.1) Description 1. Antenna: connect the antenna to the GSM module; place the antenna as far as possible from the WT-1010C2 and do not leave any coiling of the antenna cable to avoid radiant interference 2. SIM Card: disable the PIN code and set it to 1234 (default)
SMS with a certain command. Note: When sending normal SMS with command below, the WT-1010C2 will turn On / Off the output relay and reply a message of output has turned On / Off to a programmable phone numbers.
SIM card lines up with the clipped corner of the SIM holder 3. Close the SIM door 4. Slide the SIM door to lock the SIM card in place 3.4) Power up the WT-1010C2 When power up the WT 1010C2, it will display as below LOADING:>>>>>...
Page 10
(try to keep it as far as possible from the WT-1010C2 unit antenna). Usually it is possible to find a suitable location for the phone with minimal level of interference.
WT-1010C2 USER MANUAL 4. WT-1010C2 Configuration Instructions (Via Voice) 4.1 Introduction The WT-1010C2 can be programmed manually by a connected normal telephone. Connect to TEL1 Note: Before commencing programming it is advisable to read the below programming setting instructions thoroughly. To start with programming, user must...
Page 16
Each of them represents administrator 1 - 8 10) Setting the Account Number for Event Reporting When PSTN failure, AC failure or Auto Test, the WT-1010C2 will dial the programmable central station number and transmit the account number along with Contact-ID to the central station. To set the account number, you can press *36* to proceed.
Page 22
In the event the administrator has not answered the call or engaged, it could take a while for the WT-1010C2 to call the next number. You can shorten the time for every call by programming the waiting time. Press *12* to proceed.
This happens because the WT-1010C2 recognizes any GSM number as administrator and answers to it. Warning: The administrator number must be program into the WT-1010C2 unit first via voice mode in order to use SMS programming mode.
Note: You will need to enable the Password Login feature for the wireless listening function. 5.5 Setting the Account Number for Event Reporting When PSTN failure, AC failure or Auto Test, the WT-1010C2 will dial the programmable central station number and transmit the account number along with Contact-ID to the central station.
Return Message ACCT:9999 Note: Please refer to page 43 for Contact-ID Protocol for WT-1010C2 5.6 Setting the Burst On and Burst Off time of DTMF tones The Burst ON and Burst OFF timing of the sending Contact-ID can be adjust by sending the following SMS command to the unit.
In the event the administrator has not answered the call or engaged, it could take a while for the WT-1010C2 to call the next number. You can shorten the time for every call by sending the following SMS command to the unit.
Page 43
Permanent +V Output Facility 5.17.9 There is a permanent +V output when the WT-1010C2 is power on. This output is available on the connection PIN8 and ground on the main board. The output voltage is according to power supply used on WT-1010C2. It can be used to power on other facility or device.
WT-1010C2 USER MANUAL 6. Digital Communication Standard - Contact ID Protocol for WT-1010C2 Objectives a) Provide information regarding events that are occurring on a customer’s premises. This information should be in a form that can easily be interpreted by a central station operator.
Terminal against defective parts and workmanship. Witura Corporation Sdn Bhd shall, at its option, repair or replace the defective equipment upon the return of such equipment to any Witura branch. This warranty applies ONLY to defects in components and workman-ship and NOT to damage due to...