Power adapter Lithium-Ion Back-up Battery 5m GSM terminal antenna User’s Manual Contents 1. Introduction to WT-1010SA GSM Alarm System………………………………………………………………….….5 2. Main Features of the WT-1010SA….………….………………………………………………………………………..……5 3. Installation Instruction....................6 3.1 Description……………………………………………………………………………………………………………………………………………..6 3.2 WT-1010SA Inputs & Outputs Wiring Instructions……………………………………………………………………………...7 3.3 Installing the SIM Card………………………………………………………………………………………………………………………….8 3.4 Power up the WT-1010SA…………………………………………………………………………………………….……………………….8...
When no telephone service is available from your home, it ensures that critical alarm information reaches the central station. The WT-1010SA uses a GSM communicator, no distance limits to receive alarm calls or remote control the alarm system, it can also call and sends text alerts to 8 pre-set telephone number when intruder alarm triggers.
3.1) Description 1. Antenna: connect the antenna to the GSM module; place the antenna as far as possible from the WT-1010SA and do not leave any coiling of the antenna cable to avoid radiant interference 2. SIM Card: disable the PIN code and set it to 1234 (default)
SMS with a certain command. Note: When sending normal SMS with command below, the WT-1010SA will turn On / Off the output relay and reply a message of output has turned On / Off to a programmable phone numbers.
Battery WT-1010 Note: Whenever the WT-1010SA fails to logon to network or fails to detect the SIM card, it will restart automatically until it has detected the SIM card or successfully logon to network. WT1010SA – USER MANUAL – Rev.1.6 – Technical Support: Technical@witura.com...
(try to keep it as far as possible from the WT-1010SA unit antenna). Usually it is possible to find a suitable location for the phone with minimal level of interference.
4. WT-1010SA Programming Instructions (Via Fixed Line Phone) 4.1 Introduction The WT-1010SA can be programmed manually by a connected normal telephone. Note: Before commencing programming it is advisable to read the below programming setting instructions thoroughly. To start with programming, user must...
ON&OFF: 1 Then press 1# to reset REST ON&OFF: 1 Note: It is advised that you should reset the WT-1010SA unit before proceeding to the below programming section Programming the Administrator Number Step 3. Continue pressing *1* to start programming the administrator number 1...
ARM OR DISARM ON&&OFF: 1 System armed successfully Note: In Armed mode, the WT-1010SA can generate SMS alerts, alarms and dialing the administrator numbers when the inputs triggered, Auto Test, PSTN failed or AC failed. Alarm Indicator (When dialing the Administrator numbers):...
Remote Control Step 15. Enable The WT-1010SA also comes with a RF remote control. It allows you to arm or disarm the system easily from a close distance. To enable the remote control, you can press *45* to proceed.
Setting the Automatic Call Answering Feature Step 16. The WT-1010SA can be programmed to answer all incoming calls automatically even there is no fixed line phone attached to it. When the call is answered, it allows the owner to arm or disarm the system by entering a command from their phone’s keypad.
WT-1010SA USER MANUAL WT-1010SA Programming Instructions (Via SMS) Programming the WT-1010SA can also be done via SMS commands using your phone. Any programming command sent by SMS must be in CAPITAL letters. The fields between square brackets are parameters; do NOT enter the square brackets.
Page 31
In the event the administrator has not answered the call or engaged, it could take a while for the WT-1010SA to call the next number. You can shorten the time for every call by programming the waiting time. Press *12* to proceed.
Page 33
WT-1010SA USER MANUAL Enable/Disable System Power Up SMS Notification The system is able to generate SMS notification whenever the WT-1010SA is turned on. To enable this function, you can press *48* to proceed. POWER UP MSG ON&&OFF: POWER UP MSG ON&&OFF: 1...
Page 36
Setting the WT-1010SA to ignore the front dialing digits when dialing the Administrator number via Voice This function is useful when the WT-1010SA is connected to the PABX system where Access Digits are required for Extension Line/Centrex Line. To set the unit to ignore the front dialing digits, you can press *44* to proceed.
Page 37
Note: Both SPK and MIC volume level range from 1 – 4 (Default: 1). Adjust the speaker and microphone volume to compatible with your alarm panel Inquire the Software and Hardware Version of WT-1010SA via Voice To check the software and hardware version of WT-1010SA unit, you can press *13* to proceed. HW: 1.1ver SW: 4.7 ver MW: 1.3ver...
Page 40
WT-1010SA USER MANUAL Reset the WT-1010SA unit via SMS To reset the unit, you can send the following command by SMS to the unit. Text Command: *REST#XXXXXX XXXXXX stands for 6 digits password based on *PAWO# (Default: 123456) and it can be changed anytime.
Terminal against defective parts and workmanship. Witura Corporation Sdn Bhd shall, at its option, repair or replace the defective equipment upon the return of such equipment to any Witura branch. This warranty applies ONLY to defects in components and workman-ship and NOT to damage due to...