Page 3
7.10 Activate Output Relay to Stay On for a Specific Time via Voice………………………………………………………….38 7.11 Setting the Alarm Time for Audible Alarm via Voice……………………………………………………………………………….38 7.12 Setting the WT-1010C2 to Ignore the Front Digits When Dialing th e Administrator via Voice……………………………………………………………………………………………………………………………………………………………………39 7.13 Adjusting the Speaker and Microphone Volume via Voice……………………………………………………………………39 7.14 Inquire the Software and Hardware Version of WT-1010C2 via voice………………………………………………40...
2. Works over the GSM cell phone networks Units can be used wherever there is cell phone coverage 3. Telephone line backup: WT-1010C2 give priority to the lowest cost network. WT- 1010C2 uses the telephone line as the main transmission line and uses the GSM voice channel as backup 4.
Page 7
For example, Zone 3 connected to an electric door, when there is intruder or the electric door is open illegally, WT-1010C2 will receive short circuit impulse on Zone 3 and automatically sends a signal to the pre-set number and notify the owner.
Description 1. Antenna: connect the antenna to the GSM module; place the antenna as far as possible from the WT-1010C2 and do not leave any coiling of the antenna cable to avoid radiant interference 2. SIM Card: disable the PIN code and set it to 1234 (default)
SMS with a certain command. Note: When sending normal SMS with command below, the WT-1010C2 will turn On / Off the output relay and reply a message of output has turned On / Off to a programmable phone numbers.
There is a permanent +V output when the WT-1010C2 is power on. This output is available on the connection PIN8 and ground on the main board. The output voltage is according to power supply used on WT-1010C2. It can be used to power on other facility or device.
WT-1010 Battery Note: Whenever the WT-1010C2 fails to logon to network or fails to detect the SIM card, it will restart automatically until it has detected the SIM card or successfully logon to network. Dialing a number from the attached telephone set After the GSM module is connected to the GSM network, an attached fixed line phone can be used to make calls.
If the noise is disturbing, change the location of the phone set (try to keep it as far as possible from the WT-1010C2 unit antenna). Usually it is possible to find a suitable location for the phone with minimal level of interference.
ON&OFF: 1 Then press 1# to reset REST ON&OFF: 1 Note: It is advised that you should reset the WT-1010C2 unit before proceeding to the below programming section Programming the Administrator Step 3. Continue pressing *1* to start programming the administrator number 1 TEL: WT-1010C2 –...
Value: 3 stands for 50~60ms Value: 4 stands for 60~80ms Value: 5 stands for 80~100ms Warning! The WT-1010C2’s Contact ID Protocols are complied with the Digital Communication Standard of Ademco. You are advised to go through the Digital Communication Standard here www.smartelectron.ru/files/DC-05_Contact_ID.pdf before proceed with this setting.
ARM OR DISARM ON&&OFF: 1 System armed successfully Note: In Armed mode, the WT-1010C2 can generate SMS alerts, alarms and dialing the administrator numbers when the inputs triggered, Auto Test, PSTN failed or AC failed. Alarm Indicator (When dialing the Administrator numbers):...
Setting the Automatic Call Answering Feature Step 15. The WT-1010C2 can be programmed to answer all incoming calls automatically even there is no fixed line phone attached to it. When the call is answered, it allows the owner to arm or disarm the system by entering a command from their phone’s keypad. To turn on this function, you can press *35* to proceed.
This happens because the WT-1010C2 recognizes any GSM number as administrator and answers to it. Warning! The administrator number must be programmed into the WT-1010C2 unit first via voice mode in order to use SMS programming mode.
In the event the administrator has not answered the call or engaged, it could take a while for the WT-1010C2 to call the next number. You can shorten the time for every call by programming the waiting time. Press *12* to proceed.
WT-1010C2 USER MANUAL 7.8 Enable/Disable System Power Up SMS Notification The system is able to generate SMS notification whenever the WT-1010C2 is turned on. To enable this function, you can press *46* to proceed. POWER UP MSG ON&&OFF: POWER UP MSG ON&&OFF: 1...
7.12 Setting the WT-1010C2 to ignore the front dialing digits when dialing the Administrator via Voice This function is useful when the WT-1010C2 is connected to the PABX system where Access Digits are required for Extension Line/Centrex Line. To set the unit to ignore the front dialing digits, you can press *44* to proceed.
Note: Both SPK and MIC volume level range from 1 – 4 (Default: 1). Adjust the speaker and microphone volume to compatible with your alarm panel 7.14 Inquire the Software and Hardware Version of WT-1010C2 via Voice To check the software and hardware version of WT-1010C2 unit, you can press *13* to proceed. HW: 1.1ver SW: 1.0 ver MW: 1.5ver...
Terminal against defective parts and workmanship. Witura Corporation Sdn Bhd shall, at its option, repair or replace the defective equipment upon the return of such equipment to any Witura branch. This warranty applies ONLY to defects in components and workman-ship and NOT to damage due to causes beyond the...