Table of Contents
Advertisement
Quick Links
B R A N D
Model HPX60 Series
Automatic Battery Charger
User's Manual
Rev. 1.0
October 17, 2006
For Sales, Support and Service
phone: 407-331-4793
fax: 407-331-4708
website: www.xenotronix.com
email: information@xenotronix.com
Xenotronix/TLI, Inc.
2541 Tracy Road
Toledo, Ohio 43619
Phone: 419-666-6982
Fax: 419-666-6534
Advertisement
Table of Contents
Related Manuals for Xenotronix HPX60 Series
Summary of Contents for Xenotronix HPX60 Series
- Page 1 B R A N D Model HPX60 Series Automatic Battery Charger User’s Manual Rev. 1.0 October 17, 2006 For Sales, Support and Service phone: 407-331-4793 fax: 407-331-4708 website: www.xenotronix.com email: information@xenotronix.com Xenotronix/TLI, Inc. 2541 Tracy Road Toledo, Ohio 43619 Phone: 419-666-6982...
- Page 2 Notice to the User The information contained in this manual is believed to be correct. However, Xenotronix/TLI, Inc. assumes no responsibility for any inaccuracies therein. Information in this manual is subject to change without notice. No part of this manual may be reproduced or transmitted in any form, electronic or mechanical, for any purpose, without the express written permission of Xenotronix/TLI, Inc.
-
Page 3: Table Of Contents
TABLE OF CONTENTS Model HPX60 Automatic Battery Charger – User’s Manual Important Safety Instructions ........1 Introduction . -
Page 4: Important Safety Instructions
Refer service to qualified service personnel. Recharge batteries in well ventilated areas to prevent build-up of explosive gases. Allow space around unit and adequate air circulation to reduce internal heat buildup. Do not operate in a small, enclosed space. Xenotronix/TLI... -
Page 5: Introduction
Connect the red insulated output clip to the positive battery terminal and connect the black insulated output clip to the negative battery terminal. If the charger is provided with a polarized connector, make sure your battery connector is wired to match the output connector. Xenotronix/TLI... -
Page 6: Charging Notes And Tips
When charging a smaller capacity battery, the battery may be undercharged because the charger switches into float charge mode too early (relative to Xenotronix/TLI... -
Page 7: Troubleshooting
Xenotronix/TLI can make custom units, or modify our existing units, to exactly match your charging needs. Call our sales department for technical information and pricing. -
Page 8: Maintenance Instructions
267 mA Float Voltage 13.60 VDC 27.20 VDC Other Models (standard calibration): Charge Amps see marking label Charge Voltage 2.40 V/Cell Switch Amps approx. Charge Amps/7.5 Float Voltage 2.267 V/Cell Safety Agency Approval: CSA (12 V models only) Xenotronix/TLI... -
Page 9: Battery Recommendations
HPX60 User’s Manual BATTERY RECOMMENDATIONS Lead-acid batteries charged @ C/10 rate. Smaller capacity batteries may require a smaller charge current to be safely charged. Consult the battery manufacturer or Xenotronix/TLI. Model Battery HPX60-12C400 12 V, 40 AH HPX60-24C200 24 V, 20 AH AH = Ampere-hours. -
Page 10: Important Precautions
HPX60 User’s Manual Model HPX60 Series Automatic Parallel Battery Charger Supplemental Instructions IMPORTANT PRECAUTIONS Follow the battery manufacturer’s recommendations when selecting a battery for use with this unit. The battery should be able to accept the full rated output current of this unit or the battery may be damaged if the load is disconnected with the battery in a discharged condition. -
Page 11: Battery Charger Specifications
BATTERY CHARGER SPECIFICATIONS Output Ratings (standard calibration): Model HPX60-012P400 HPX60-24P200 Charge Amps Maximum Continuous Load 2 A Voltage 13.60 VDC 27.20 VDC Other Models (standard calibration): Charge Amps see marking label Maximum Continuous Load ½ of Charge Amps Voltage 2.267 V/Cell Xenotronix/TLI...
Need help?
Do you have a question about the HPX60 Series and is the answer not in the manual?
Questions and answers