On Screen Display - Harman Kardon AVR80II Owner's Manual

On Screen Menus
In addition to the information shown on
the front panel display, it is also possible
to obtain the unit's current status
through the use of on screen video mes-
sages. The on screen menus may also be
used to control many aspects of the
receiver and to make adjustments and
selections.
To activate the On Screen display system,
press and hold the
SCREEN DISPLAY
button on the remote for three sec-
s
onds. This will cause a status summary
display to be shown on the screen for ten
seconds. (Figure #5). Once the video dis-
plays are enabled, this status screen will
also appear when the unit is turned on.
NOTE: In order to view the on screen
menu displays the receiver must be con-
nected to the standard, composite video
input of a TV monitor or projector. The
on screen displays are NOT visible via the
"S" video output.
The status screen displays the following
information:
: This is the input
AUDIO SOURCE
currently selected for audio.
: This is the input
VIDEO SOURCE
currently selected for video.
: This is the source cur-
TAPE1 OUT
rently routed to the Tape 1 audio out-
put for recording.
: This is the source cur-
VCR1 OUT
rently routed to the VCR 1 video out-
put for recording.

On Screen Display

27
: This is the currently selected
MODE
audio/surround mode.
: This is the source cur-
MULTIROOM
rently selected for listening in remote
room locations.
: This is the cur-
MASTER VOLUME
rent volume level. Note that volume
appears as a horizontal scale. The
"0dB" reference level is indicated by
a solid block Í , while volume levels
above or below the reference are indi-
cated by double vertical bars
Function Displays and Messages
Once the On Screen Displays have been
activated, they appear when certain func-
tions are performed from the front panel
buttons or the remote control. These
messages are three line displays with the
current function shown on the top line
and information about the selection or
choice on the bottom two lines.
The following function/operation display
screens are available:
Surround Mode and Delay
When the surround mode is changed or
the delay timing is adjusted, this message
will appear at the bottom of the video
screen. The top line is the surround
mode, the bottom line is the delay time
for that mode. (Figure #6) Note that
delay time will not be displayed in the
, or
MONAURAL STEREO DOLBY 3
modes, as these modes do not
STEREO
have rear channel information.
A U D I O
V I D E O
T A P E 1
V C R 1
M O D E
M U L T I
M A S T E R
Figure 5
±
.
M O D E
D E L A Y
Figure 6
< F U N C T I O N
A U D I O : T U N E R
V I D E O : V C R 1
Figure 7
< C O P Y
T A P E
V C R 1
Figure 8
F R O N T
F R O N T
C E N T E R
S U R R O U N D
S U R R O U N D
S U B W O O F E R
Figure 9
S O U R C E : T U N E R
S O U R C E : V C R 2
O U T : C D
O U T : A U X
: D O L B Y
P R O L O G I C
R O O M : T U N E R
V O L U M E
||
: T H X
C I N E M A
T I M E : 2 0 m s e c
S E L E C T >
F U N C T I O N >
O U T : T U N E R
O U T : V C R 2
L : + 1 d B
R : 2 d B
: + 5 d B
L : 1 0 d B
R : + 3 d B
: 0 d B