AVR 8000 Audio/Video Receiver Introduction Safety Information Unpacking Front Panel Controls Front Panel Information Display Rear Panel Connections Main Remote Control Functions Zone II Remote Control Functions Installation and Connections System Configuration Speaker Placement System Setup Input Setup Speaker Setup...
AVR 8000 is able to deliver. If you have any questions about this product, its installation or its operation, please contact your retailer or custom installer.
Safety Information Important Safety Information Verify Line Voltage Before Use Your AVR 8000 has been designed for use with 120-volt AC current. Connection to a line volt- age other than that for which it is intended can create a safety and fire hazard and may damage the unit.
System Power Control: When the Main Power Switch is “ON, ” press this button to turn on the AVR 8000; press it again to turn the unit off. Note that the Power Indicator 6Ch/8Ch Direct Button Preset Station Selector...
Page 6
6.1/7.1 channel operation. Volume Control: Turn this knob clockwise to increase the volume, counterclockwise to decrease the volume. If the AVR 8000 is muted, adjusting volume control will automatically release the unit from the silenced condition. Input Indicators: A green LED will light to the left of the input that is currently the input source for the AVR 8000.
Front Panel Information Display Upper Display Line Lower Display Line OSD Indicator Multiroom Indicator Upper Display Line: Depending on the unit’s status, a variety of messages will appear here. In normal operation, the current input source name will appear on this line. Lower Display Line: Depending on the unit’s status, a variety of messages will appear here.
When making speaker connections always make certain to maintain correct polarity by connecting the color-coded (white for front left and red for front right) (+) terminals on the AVR 8000 to 8 REAR PANEL CONNECTIONS ‚ ¶...
Page 9
AC device. The power will remain on at this outlet regard- less of whether the AVR 8000 is on or off. NOTE: The total power consumption of all devices connected to the accessory outlets should not exceed 100 watts.
EzSet Sensor Microphone NOTE: The function names shown here are each but- ton’s feature when used with the AVR 8000. Most but- tons have additional functions when used with other devices. See pages 44–45 for a list of these functions.
Page 11
Power Off Button: Press this button to place the AVR 8000 or a selected device in the Standby mode. Note that this will turn off the main room functions, but if the Multiroom sys- tem is activated, it will continue to function.
Page 12
Skip Up/Down Buttons: These buttons don’t have a direct function with the AVR 8000, but when used with a compatibly programmed 12 MAIN REMOTE CONTROL FUNCTIONS CD or DVD changer they will change the disc currently being played in the changer.
Page 13
8-Channel Direct Inputs ·. (See page 35 for more information.) Mute: Press this button to momentarily silence the AVR 8000 or TV set being con- trolled, depending on which device has been selected. When the AVR 8000 remote is being...
AVR 8000’s Multizone IR Input h jack. When it is used in the same room as the AVR 8000, it will control the functions of the AVR 8000 or any compatible Harman Kardon products in that room.
Digital Inputs be 4. Connect the coaxial or optical Digital Audio Outputs ad on the rear panel of the AVR 8000 to the matching digital input connec- tions on a CD-R or MiniDisc recorder. 5. Assemble the AM Loop Antenna supplied with the unit.
Page 16
IR sensor in the remote room to the AVR 8000 via an appropriate cable. Connect the sensor’s cable to the Multizone IR Input h on the AVR 8000 and use the Zone II remote to control the room volume. Alter- natively, you may install an optional volume control between the output of the amplifiers and the speakers.
Page 17
AC outlet. The AVR 8000 features a removable power cord that allows wires to be run to a complex instal- lation so that the unit, itself, need not be installed until it is ready for connection.
7.1 operation. At least 6 inches from ceiling At least 2 feet When the AVR 8000 is used in 5.1-channel operation, the preferred location for surround speakers is on the side walls of the room, at or slightly behind the listening position. In a 7.1- channel system, both side surround and back surround speakers are required.
You are now ready to power up the AVR 8000 to begin these final adjustments. 1. Make certain that the AC power cord is firmly inserted in to the AC Power Cord Receptacle fi...
Input Setup The first step in configuring the AVR 8000 is to configure each input. Note that the once an input is selected, all settings for the Digital Input, Speaker Configuration, Surround Mode and Delay Timing will “attach”...
There is no need to adjust these settings when configuring subsequent inputs. Speaker Setup This menu tells the AVR 8000 which type of speakers are in use. This is important as it adjusts the settings that decide whether your system should use the “5-channel” or “6-channel/7-channel”...
However, to make it easier to establish the initial parameters for the AVR 8000, it is best to select Dolby Pro Logic II or Logic 7 for most analog inputs and Dolby Digital for inputs connected to digital sources.
Page 23
, the appropriate modes will appear for that type of operation. In addition, some of the modes available in the AVR 8000 will not appear unless a digital source is selected and is playing the correct bitstream. To select the mode that will be used as the...
Output level adjustment is a key part of the configuration of any surround sound product. It is particularly important for a digital receiver such as the AVR 8000, as correct outputs ensure that you hear sound tracks with the proper directionality and intensity.
While the AVR 8000 allows you to set output levels man- ually, we recommend that EzSet system be used when the AVR is first installed to establish the initial level settings.
Bass Peak Limiter The AVR 8000 includes a bass peak level limiter as part of the THX Ultra program to protect your subwoofer from being damaged by exces- sive levels.
Page 27
AVR. Once the settings outlined on the previous pages have been made, the AVR 8000 is ready for operation. While there are some additional settings to be made, these are best done after...
Dolby Pro Logic mode for those who prefer that sonic presentation. Logic 7 Cinema Exclusive to Harman Kardon for A/V receivers, Logic 7 is an advanced mode that extracts the maximum surround information from Logic 7 Music either surround-encoded programs or conventional stereo material.
Page 29
Operation MODE FEATURES VMAx Near When only the two front channel loudspeakers are used, Harman’s patented VMAx mode delivers a three-dimensional sound space VMAx Far with the illusion of “phantom speakers” at the center and surround positions. The VMAx N, or “Near Field, ” mode should be selected when your listening position is less than five feet from the speakers.
Turning the AVR 8000 On or Off • When using the AVR 8000 for the first time, you must press the Main Power Switch on the front panel to turn the unit on. This places...
(HDTV) system. Note that an optional, external RF demodulator is required to use the AVR 8000 to listen to the Dolby Digital soundtracks available on laser discs. Connect the RF output of the LD player...
Page 32
AVR 8000 uses a variety of indicators to let you know what type of signal is present. This will help you to understand the choice of modes.
Indicators will light, and the audio will begin playing. NOTES: • The AVR 8000 is only capable of playing sig- nals in the MP3 (MPEG 1/Layer 3) format. It is not compatible with other computer audio codecs. • The digital audio input signal may be either optical or coaxial, but the signal must be in the PCM format.
Once changed to an output, the setting will remain as long as the AVR 8000 is turned on, unless the setting is changed in the OSD menu system, as described above. Note, howev- er, that once the AVR 8000 is turned off, the setting is cancelled.
6-Channel/8-Channel Direct Input The AVR 8000 is equipped for future expansion through the use of optional, external adapters for formats that the AVR 8000 may not be capable of processing or to allow connection to the output of high-resolution optical audio playback systems such as DVD-Audio or SACD.
Turn-On Volume Level As is the case with most audio/video receivers, when the AVR 8000 is turned on, it will always return to the volume setting in effect when the unit was turned off. However, you may prefer to...
Page 37
Note that this setting is temporary and will remain active only until it is changed or until the AVR 8000 is turned off. Once the unit is turned off, the semi-OSD displays will remain activated, even if they were switched off for the previous listening session.
Selector buttons to turn on to a specific source. As long as an IR feed to the AVR 8000 has been established from the remote room, using any of the buttons on either remote will control...
Auto Search Method. Auto Search Method If the unit you wish to include in the AVR 8000’s remote is not listed in the code tables in this manual or if the code does not seem to operate...
Program/SPL Indicator flashes amber and the light under the device selector but- ton turns red. Release the buttons. 4. Press the button on the AVR 8000 remote that you wish to program. Note that the Program/SPL Indicator will stop flashing.
Selectors will blink and then turn off. Example: To program the Macro 1 button so that it turns on the AVR 8000, TV and a Cable Box, follow these steps: • Press the Macro 1 Button Mute Button at the same time and then release them.
For example, if you have two VCRs but no satellite receiver, you may program the “SAT” button to operate a second VCR. Before following the normal programming steps for...
Function List No. Button Name AVR Function Power On Power On Power On Power Off Power Off Power Off Mute Mute Mute AVR Select DVD Input Select DVD Select CD Input Select Tape Tape Input Select VID 1 Video 1 Select VID 2 Video 2 Select 10 VID 3...
Page 45
Function List (continued) No. Button Name AVR Function 46 Direct Direct Tuner Entry Angle 47 Clear Clear Clear 48 Preset Up Preset Tune Up Slow Forward +10 49 Tune Down Tune Down Prev Chapter Track Increment 50 OSD 51 D. Skip Disc Skip 52 Preset Down Preset Tune Down...
After the pause, reconnect the AC power cord and check the unit’s operation. If the system still malfunctions, a system reset may clear the problem. To clear the AVR 8000’s entire system memory including tuner presets, output level settings, 56 TROUBLESHOOTING GUIDE SOLUTION •...
Height measurement includes feet and chassis. All features and specifications are subject to change without notice. Harman Kardon is a registered trademark, and Power for the Digital Revolution is a trademark, of Harman Kardon, Inc. THX and THX Ultra are manufactured under license from Lucasfilm Ltd.