Basic Operation - Harman Kardon AVR80II Owner's Manual

Station Name Preset
In addition to identifying stations by
their broadcast frequency, each preset
station may be assigned a name using
alphanumeric characters. This enables
you to identify a station by its call letters,
program format, or any other five char-
acter phrase.
To enter a station name, first preset all
stations you wish to program into the
tuner's memory. Then, follow these steps:
1. Tune to the desired preset station.
2. Press the button
MEMO
front panel for more than three seconds.
3. Note that a character on the left side of
the main information display will start to
blink.
4. Enter the first character of the name
using either the front panel
buttons or the alphanumeric but-
^
¤
tons on the remote.
m
A. To use the front panel buttons simply
press and hold ^
TUNE ⁄
until the desired letter or number
appears. Note that the upper case alpha-
bet will appear, followed by the numbers
through , and then a
1 0
blank space. Tapping the button will
advance the display one character at a
time; holding it down will move the dis-
play quickly. If you pass by the desired
character, use the
TUNE ¤
the display in reverse.
After entering the first character, press
to move to the next position
MEMO Ú
and note that the next digit will blink.
Use the same procedure outline above to
enter a character.
When you have entered a digit or
"blank" in all five spaces, press
to confirm the entry
Ú

Basic Operation

B. To use the remote for character entry,
press the button corresponding to the
desired letter or number. Press it once to
enter the first printed letter, twice for the
second, three times for the third and four
times for the number. Press the "
ton to enter a blank space. (For example,
press the "
" ", three times for a "
A
times to enter a "
Use the
MEMO
the next digit position. When all five
spaces have been filled, press
again to confirm the entry.
Ú on the
Once a station name has been attached to
a preset position, the station's frequency
will appear briefly when the unit is tuned
to that station. After a few seconds the
preset name will appear in the display.
Tuning Preset Stations
or
TUNE ⁄
Stations preset into the tuner's memory
may be recalled in a number of ways.
1. To recall a station directly enter a
number from 1 to 30 using the number
button
buttons on the remote s
a. To enter a single digit memory
location, press
indicating a
or enter the number and wait a few
seconds.
b. If an invalid number (other than
1–30) is entered in error, that number
to move will flash to alert you that the entry is
^
invalid and the display will return to
the previous frequency display.
2. To scan through the list of preset sta-
tions, press the
button on the front panel
to move up or down thorough the mem-
ory presets one by one, or press and hold
the button to quickly scan through the
MEMO
list of stations.
26
" but-
9
" button once to enter an
ABC
" and four
C
".)
1
button to move to
o
MEMO
m .
before the number,
0
or
P-SET ⁄ P-SET ¤
. Press once
$
3. To automatically review each station
in the memory, press the
P-SCAN
ton . Note that the
n %
P-SCAN
›
cator will blink.
4. The tuner will move up through the
list of stations, pausing to play each for
five seconds. Note that preset numbers
where no station has been programmed
will be skipped.
5. When the desired station is reached
press or
P-SCAN % CLEAR Û
Clearing Preset Stations
Once stations are programmed into the
preset memories, it is possible to remove
them individually or as a group.
To remove a single station from the
memory:
1. Recall the station by pressing the but-
tons on the remote corresponding to the
station's memory location.
2. Press the button
MEMO
and observe that the
MEMO
will blink.
3. While the indicator is blinking, press
the button within five sec-
Û
CLEAR
onds. The word will show briefly
CLEAR
to confirm that the memory position has
been cleared.
To clear all memory locations, the
volume level and surround mode
memories:
1. Press the button
MEMO
the button
Û m
CLEAR
time.
NOTE: When a complete memory clear is
performed the AVR80 will turn off as
II
part of the process. After clearing the
memory it is necessary to reset all sta-
tions and set up parameters.
but-
indi-
.
Ú or o
£
indicator
and
Ú o
at the same