1. Manuals
  2. Brands
  3. Security Camera King Manuals
  4. Security Camera
  5. CVIOD-EL2MPIR50
  6. User manual

Security Camera King CVIOD-EL2MPIR50 User Manual

2 megapixel hdcvi camera
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
CVIOD-EL2MPIR50 User's Manual
Version 1.1.0

Advertisement

Table of Contents
loading

Related Manuals for Security Camera King CVIOD-EL2MPIR50

Summary of Contents for Security Camera King CVIOD-EL2MPIR50

  • Page 1 CVIOD-EL2MPIR50 User’s Manual Version 1.1.0...

  • Page 2: Table Of Contents

    Overview ........................1 Features ........................1 Functions ........................1 Specifications ......................1 Framework ..........................4 Dimensions ....................... 4 2.1.1 CVIOD-EL2MPIR50..................4 Installation ..........................6 Dome Camera Installation Introduction..............6 Fixed Camera Installation..................6 Menu ............................8 Menu List ........................8 Note .........................
  • Page 3 Welcome Thank you for purchasing our HDCVI camera! This user’s manual is designed to be a reference tool for your system. Please read the following safeguard and warnings carefully before you use this series product! Please keep this user’s manual well for future reference!

  • Page 4: Important Safeguards And Warnings

    Important Safeguards and Warnings 1．Electrical safety All installation and operation here should conform to your local electrical safety codes. The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited power source is rated 12V DC in the IEC60950-1. We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation.
  • Page 5 Please shut down the device and then unplug the power cable before you begin daily maintenance work. Use the dry soft cloth to clean the device. If there is too much dust, please use the water to dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the device. Please put the dustproof cap to protect the CMOS component when you do not use the camera.

  • Page 6: General Introduction

    1 General Introduction 1.1 Overview This series megapixel HD camera conforms to the HDCVI standard. It supports video signal high-speed long distance transmission without any delay. It can be controlled by the DVR conforming to the HDCVI. 1.2 Features  High-performance CMOS image sensor, megapixel definition.
  • Page 7 Please refer to the following sheet for specification. Model 2 Megapixel HDCVI Camera Parameter CVIOD-EL2MPIR50 Video Processor 1/3" 2 Megapixel CMOS Video Format PAL/NTSC Effective Pixel 1920 (H) *1080 (V) Min Illumination 0.05Lux@（F1.2，AGC ON），0 Lux with IR Electronic Shutter Support slow shutter. 1/3s～1/100,000s...
  • Page 8 Weight 300g 450g 450g Installation Mode Wall mount Wall mount In-ceiling mount...

  • Page 9: Framework

    2 Framework 2.1 Dimensions CVIOD-EL2MPIR50 2.1.1 Please refer to the following figures for the dimension information. The unit is mm. See Figure 2-1. Figure 2-1 2.1.2 Please refer to the following figures for the dimension information. The unit is mm. See Figure 2-2.
  • Page 10 Figure 2-3 When the standard definition/high definition switch control cable is short circuit, system outputs standard definition video. Otherwise, when the circuit is open, system outputs the high definition video.

  • Page 11: Installation

    3 Installation Important  Before the installation, please make sure the installation surface can sustain at least 3X weight of the bracket and the camera. 3.1 Dome Camera Installation Introduction Please follow the steps listed below. See Figure 3-1. Step 1 Turn clockwise to remove the decoration ring from the snap joints.
  • Page 12 Step 1 Install the camera bracket. Please install the expansion bolt if you want to install in the cement wall (Please make sure the installation holes of the expansion bolts are the same with the bracket.) Then you can install the bracket. If you want to install in the wood surface, please skip the first step and then use the self-tapping screws to install the bracket directly.

  • Page 13: Menu

    4 Menu 4.1 Menu List The 1 The 2nd The 3 Exposure Exposure Auto Mode Gain Max 0～100 Noise Gain Min 0～100 Return&Exit For the 2 and the 3 menu, when you click Exit button to exit, system saves current setup by default.
  • Page 14 The 1 The 2nd The 3 Title Mirror/Flip Mirror OFF/ON Flip OFF/ON Return&Exit Motion Detect Area Sel 0～3 There are four motion detect zones ranging from 0 to 3. You need to set parameters for each zone. Area State OFF/ON Sensitivity 0～100 Threshold...

  • Page 15: Note

    4.2 Note Parameter Function Brightness It is to adjust monitor window bright. The value ranges from 0 to 100. The default value is 50. The larger the number is, the bright the video is. When you input the value here, the bright section and the dark section of the video will be adjusted accordingly.

  • Page 16: Appendix Toxic Or Hazardous Materials Or Elements

    Appendix Toxic or Hazardous Materials or Elements Toxic or Hazardous Materials or Elements Component Name Cr VI PBDE Circuit Board ○ ○ ○ ○ ○ ○ Component Device ○ ○ ○ ○ ○ ○ Construction Material ○ ○ ○ ○ ○...

Table of Contents