Related Manuals for Perlick SDBR48
Summary of Contents for Perlick SDBR48
-
Page 1: Operation Manual
Installation & Operation Manual Commercial Back Bar Sliding Door SDB & SDP Series Model SDBR48 Shown Form No. 2722013... -
Page 2: Table Of Contents
For your own protection, never return Serial Number: _________________________ merchandise for credit without our approval. Purchase Date: _______________________ We thank you for selecting a Perlick product Dealer Name & Address and assure you of our continuing interest in your ______________________________________ satisfaction. -
Page 3: Prior To Installation
“Condensate Evapaway’ pan and heater. cabinet for hidden damage. If damage is discovered, file your claim immediately with the Electrical transport company. Perlick is not responsible for The cabinet must be connected to a separately damage in transit. fused power source (see Electrical Specification... -
Page 4: Installation
Models SDB/SDP Installation & Operation Manual InsTallaTIon General Information Installing the Unit If unit has been laid on its • For units equipped with a power cord, the CAUTION cord and plug may be aligned with a recess in back or sides, place unit the back panel to allow the unit to be pushed upright and allow minimum of 24 hours before closer to the wall. -
Page 5: Operation
Models SDB/SDP Installation & Operation Manual Sealing Cabinet to Floor Cabinet For units without casters or legs, it may be necessary to seal the base of the cabinet to Bead Silicon the floor. This can be accomplished by laying a Sealer (RTV) bead of silicone sealant between the base of the cabinet and the floor (Figure 1). -
Page 6: Adjustments
Models SDB/SDP Installation & Operation Manual adjusTmenTs Never attempt to repair or 5. Plug new LED into harness and secure to DANGER perform maintenance on housing using screws removed in step 2. the unit until the main electrical power to the 6. Snap LED cover into place. unit has been disconnected! Sliding Doors Shelving Adjustment... -
Page 7: Maintenance
Models SDB/SDP Installation & Operation Manual maInTenanCe Stainless Steel Care & Cleaning parallel to the lines. When the grain cannot be seen, play it safe and do not use a circular motion. General Polish in a consistent straight pattern. Contrary to popular belief, stainless steel is Use alkaline, alkaline chlorinated or non-chloride susceptible to rusting. -
Page 8: Cleaning The Condenser
Models SDB/SDP Installation & Operation Manual Cleaning the Condenser A v o i d d a m a g i n g o r CAUTION crushing the condenser The condenser (located behind front grille cover) fins or tubing. Failure to follow this procedure should be cleaned every three (3) months. Use may damage the compressor and void the a soft bristle brush and vacuum to remove the warranty. -
Page 9: Troubleshooting
LED Controller display is flashing Controller has a data or memory failure. Reset both compartment presets. “EE”. If problem persists, contact your Perlick Service Department. Unit is not running. No power to the unit. Home circuit breaker tripped. Reset circuit breaker. - Page 10 Perlick products and offer superior • Write to Perlick Corporation, Customer service life. The use of non-Perlick parts can Service Department, 8300 West Good Hope damage the unit and may void the warranty. Road, Milwaukee, WI 53223.
-
Page 11: Dimensions
Models SDB/SDP Installation & Operation Manual dImensIons Printed in USA 0213... - Page 12 Models SDB/SDP Installation & Operation Manual Printed in USA 0213...
- Page 13 Models SDB/SDP Installation & Operation Manual Printed in USA 0213...
- Page 14 Models SDB/SDP Installation & Operation Manual Printed in USA 0213...
-
Page 15: Wiring Diagrams
Models SDB/SDP Installation & Operation Manual WIrInG dIaGrams Printed in USA 0213... - Page 16 Models SDB/SDP Installation & Operation Manual Printed in USA 0213...
- Page 17 Models SDB/SDP Installation & Operation Manual Printed in USA 0213...
- Page 18 Models SDB/SDP Installation & Operation Manual Printed in USA 0213...
-
Page 19: Warranty
Any changes to an carrier’s responsibility. Before giving the carrier Order must be in writing and signed by Perlick a clean receipt at time of delivery, make sure you and Buyer. - Page 20 Perlick’s one year labor warranty provides series back bars and accessory parts is 20%. that Perlick will pay for the cost of any labor to The minimum restocking charge for custom replace any defective part for up to one year series cabinets is 50%.
Need help?
Do you have a question about the SDBR48 and is the answer not in the manual?
Questions and answers