Harman Advance Pellet Stove Installation & Operating Manual

Harman Advance Pellet Stove Installation & Operating Manual

Advance pellet stove
Hide thumbs Also See for Advance Pellet Stove:

Advertisement

Installation & Operating manual
The harman Advance Pellet Stove
r19
"Ce manuel est disponible en Français sur demande"

SAFETY NOTICE

PlEASE rEAd ThIS ENTIrE mANuAl bEFOrE YOu INSTAll ANd uSE YOur NEw rOOm hEATEr. FAIlurE
TO FOllOw INSTruCTIONS mAY rESulT IN PrOPErTY dAmAgE, bOdIlY INjurY, Or EvEN dEATh.
FOr uSE IN ThE u.S. ANd CANAdA. SuITAblE FOr INSTAllATION IN mObIlE hOmES
IF ThIS hArmAN STOvE IS NOT PrOPErlY INSTAllEd, A hOuSE FIrE mAY rESulT. FOr YOur SAFETY, FOl-
lOw INSTAllATION dIrECTIONS.
CONTACT lOCAl buIldINg Or FIrE OFFICIAlS AbOuT rESTrICTIONS ANd INSTAllATION INSPECTION
rEQuIrEmENTS IN YOur ArEA.
CONTACT YOur lOCAl AuThOrITY (SuCh AS muNICIPAl buIldINg dEPArTmENT, FIrE dEPArTmENT, FIrE
PrEvENTION burEAu, ETC.) TO dETErmINE ThE NEEd FOr A PErmIT.
CETTE guIdE d'uTIlISATION EST dISPONIblE EN FrANCAIS. ChEz vOTrE CONCESSIONNAIrE dE hArmAN
hOmE hEATINg.
SAvE ThESE INSTruCTIONS.
#3-90-09730

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Advance Pellet Stove and is the answer not in the manual?

Questions and answers

Summary of Contents for Harman Advance Pellet Stove

  • Page 1: Safety Notice

    TO FOllOw INSTruCTIONS mAY rESulT IN PrOPErTY dAmAgE, bOdIlY INjurY, Or EvEN dEATh. FOr uSE IN ThE u.S. ANd CANAdA. SuITAblE FOr INSTAllATION IN mObIlE hOmES IF ThIS hArmAN STOvE IS NOT PrOPErlY INSTAllEd, A hOuSE FIrE mAY rESulT. FOr YOur SAFETY, FOl- lOw INSTAllATION dIrECTIONS.
  • Page 3: Table Of Contents

    Note: This appliance is also approved for installation into a shop. maintenance Trouble-Shooting SAFETY NOTICE: IF THIS HARMAN ADVANCE PEL- LET STOVE IS NOT PROPERLY INSTALLED. A HOUSE Specifications FIRE MAY RESULT. FOR YOUR SAFETY, FOLLOW THE INSTALLATION DIRECTIONS. CONTACT LOCAL BUILD-...
  • Page 4 Automatic Ignition/Operation The Advance pellet stove is more than just automatic ignition, it is also automatic temperature control. The automatic system will allow the fire size to be adjusted to match the heating needs and even put the fire out if necessary. If heat is needed after the fire is out, the Advance will automatically re-ignite and adjust the fire size to match the heating need.
  • Page 5 Automatic Start up Starting First Fire Igniter Switch to "AuTO" (up position) Make sure the unit is plugged into a 120 VAC, 60 HZ electrical source. The power light should be the only light lit. To avoid unwanted smoke, be sure there is no fuel or combustibles in the ash pan prior to lighting.
  • Page 6: Manual Operation

    Ignition/Operation The Advance Pellet Stove is capable of manual operation. This also allows the opera- tor to manually control operation during an emergency (i.e. igniter failure.) The unit can be switched between "AUTO" and "MANUAL" at any time during operation.
  • Page 7 manual Start up Starting First Fire Igniter Switch to "mANuAl" Fig. 4 (down position) Make sure the unit is plugged into a 120 VAC, 60 HZ electrical source. The power light should be the only light lit. Fig. 3 See Note 7. To avoid unwanted smoke, be sure there is no 1"...
  • Page 8: Esp Control

    Fahrenheit. It also allows you to adjust the only. Requires special DDM to vary the distribution blower stove temperature while in Stove Temp Mode using monitor supplied to Harman speed by turning the knob to the inner scale marked from 1 to 7. Dealers exclusively.
  • Page 9 7" Several issues must be addressed when selecting a suitable location for your Advance Pellet Stove. Observing required clearances to combustible materials, the proximity to a safe chimney or venting system, and the accessibility of electrical Fig.6 supply must all be considered.
  • Page 10 removing Side doors for Installation removing Side doors Figure 9 Use hand hole to swing open side doors to at least Figure 10 Side Remove side doors by lifting upward on the door until Door the bottom pin is out of its hole. Move the bottom of Fig.
  • Page 11 low draft voltage Adjustment Combustion Motor Speed Control Low draft only set point. The small straight screwdriver slot is plastic; therefore, the unit can be adjusted while in operation. Draft Meter bolt hole location Fig.15 Fig.14 A simple draft test should be performed after These units are pre-tested at the factory with exactly completing the flue pipe installation.
  • Page 12 room Sensor and Air grill Installation Air grill Installation room Sensor Installation Fig. 17 Fig. 16 The room sensor is a small temperature sensor Insert the two tail end hooks of the Air Grill Assembly on the end of a 60" gray or black wire. This sensor is up under the stove top edge.
  • Page 13: Venting

    • Vents should not be placed below ventilated Outside Air: soffits. Run the vent above the roof. harman home heating and hearth & home Technologies recommend attaching outside air • Avoid venting into alcove locations. in all installations, especially lower level and •...
  • Page 14 Or CEIlINg. direct vent wall Passthrough Outside Air The harman direct vent wall Passthrough (Part # 1- Outside air is necessary in mobile homes and 00-677077) makes installing your harman Pellet Stove where building codes require. The benefit of outside with outside air much easier.
  • Page 15 venting #1 Preferred method This method provides excellent venting for normal operation and allows the stove to be installed closest to the wall. One inch from the wall is safe; however, two or three inches allows better access to remove the rear panel.
  • Page 16 venting #3 Installing into an existing chimney This method can be used for normal opera- tion. This method also provides natural draft in the event of a power failure. If the chimney condition is questionable you may want to install a liner as in method #6.
  • Page 17 venting #5 Installing into an existing fireplace chimney This method provides excellent venting for nor- mal operation. This method also provides natural draft in the event of a power failure. In Canada and some places in the US it is required that the vent pipe extend all the way to the top of the chimney.
  • Page 18 venting #7 Installing through the ceiling vent minimum flue vent configuration Through the ceiling vent, follow PL vent It is recommended that outside air be installed with manufacturer's recommendations when using wall this venting configuration. and ceiling pass through. Storm collar 12"...
  • Page 19 venting H. A vent must not be installed within 3 feet (90 cm) requirements for Terminating the above a gas meter/regulator assembly when measured venting from the horizontal center-line of the regulator. I. The clearance to service regulator vent outlet must WARNING: Venting terminals must not be recessed be a minimum of 6 feet.
  • Page 20 venting dO NOT INSTAll A FluE dAmPEr IN ThE wArNINg EXhAuST vENTINg SYSTEm OF ThIS mObIlE hOmE rEgulATIONS dO uNIT. NOT AllOw INSTAllATION IN A rOOm dESIgNATEd FOr SlEEPINg. dO NOT CONNECT ThIS uNIT TO A ChImNEY FluE SErvINg ANOThEr APPlIANCE. CAuTION ThE STruCTurAl INTEgrITY OF ThE mObIlE hOmE FlOOr, wAll, ANd...
  • Page 21: Maintenance

    maintenance - Emptying Ashes Ash Pan removal and reattachment CAUTION: Surfaces are hot while in operation, Wear gloves to protect from burns. Figure 29 Open side doors. Figure 30 Release spring latches on the right and left side of the ash Fig.
  • Page 22 To remove the view door from the stove, hold the door by the bottom and lift upward, off of the hinge pins. See Fig. 36. The glass in your Harman stove is a special ceramic Fig. 36 glass. •...
  • Page 23 maintenance - burn Pot burn Pot Cleaning and maintenance 1. Scrape the top holed surface and sides of the burn pot. (Fig 38) It is not necessary to completely remove all material from the burn pot. The excess will be pushed out during the next use. 2.
  • Page 24 maintenance - Flame guide and brick Panel Flame guide and brick Panel Firebox Brick Panel Flame Guide/ Brick panel removal for Cleaning holder Burn pot Fig. 41 Figure 42 Slide brick panel straight upward with both hands. Fig. 42 Figure 43 While holding the brick panel up with one hand, remove the flame guide from the top of the burn pot.
  • Page 25 maintenance - Combustion Intake Cover Cover Retainer Handle Cleaning and maintenance for the Combustion Intake Cover You will need to remove the combustion intake cover, behind the ash pan, to clean the fan blades and rear flue tube. Figure 46 Rotate the retainer cover handle counter-clockwise upward as far as it will go (approximately 90 Figure 47...
  • Page 26 maintenance - heat Exchanger Cleaning the heat Exchanger System Slot 1. Remove brick panel and flame guide. (See Pg 24.) 2. Remove the ash pan. See Page 21. 3. Remove flue baffles located on each side of the burnpot, see Fig. 49 & 50. The baffle is held in place by inserting the tab into the slot (located toward the Hook Tab Fig.
  • Page 27 Igniter Wire - Feeder Entry Location Combustion Blower Advance Pellet Stove Safety devices The low draft Pressure Switch is a differential The Control board/ESP combination is respon- pressure switch that senses the negative pressure sible for all high limit safety control. There are 2 high (draft) in the firebox.
  • Page 28: Trouble-Shooting

    Trouble-Shooting STOvE dOES NOT FEEd SmOKE IS vISIblE COmINg OuT OF vENT 1. No fuel in hopper. 1. Air-fuel ratio is too rich. 2. Firebox draft may be too low for sensing switch in A. Feed rate too high. B. Draft too low caused by a gasket leak. feeder circuit to operate.
  • Page 29: Specifications

    Fuel Specifications Fuel and Fuel Storage Size Pellet fuel quality can fluctuate from manufacturer to • Pellets are either 1/4 inch or 5/16 inch (6-8mm) in manufacturer, and even from bag to bag. diameter Hearth & Home Technologies recommends using only •...
  • Page 30 Specifications 20.5" 7.750" 5.250" 26.625" weight 250 lbs. blower 135 cfm hopper Capacity 60 lbs. Fuel wood Pellets or Corn/Pellet mix Outside Air Size 2 3/8 inches Fuse rating 6 amp bTu range 0 to 48,000 Feed rate 1.0 lbs./hr. on minimum 6 lbs./ hr.
  • Page 31: Wiring Diagram

    Advance wiring diagram...
  • Page 32: Warranty

    Hearth & Home Technologies Inc. LIMITED LIFETIME WARRANTY Hearth & Home Technologies Inc., on behalf of its hearth brands (”HHT”), extends the following warranty for HHT gas, wood, pellet, coal and electric hearth appliances that are purchased from an HHT authorized dealer. WARRANTY COVERAGE: HHT warrants to the original owner of the HHT appliance at the site of installation, and to any transferee taking ownership of the appliance at the site of installation within two years following the date of original purchase, that the HHT appliance...
  • Page 33 WARRANTY CONDITIONS: • This warranty only covers HHT appliances that are purchased through an HHT authorized dealer or distributor. A list of HHT authorized dealers is available on the HHT branded websites. • This warranty is only valid while the HHT appliance remains at the site of original installation. •...
  • Page 34 Advance Service Parts beginning manufacturing date: N/A Pellet Stove Ending manufacturing date: Active 1-70-08730-1 (black), 1-70-08730-2 (Charcoal), 1-70-08730-3 (goldenfi re), 1-70-08730-4 (metallic blue), 1-70-08730-5 (honey glo), 1-70-08730-10 (mojave red), 1-70-08730-12 (Forest green) Part number list on following page. 01/11...
  • Page 35: Parts List

    Advance Service Parts beginning manufacturing date: N/A Ending manufacturing date: Active IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement Stocked parts for your appliance please provide model number and serial number. All parts listed in this manual may be ordered from an authorized dealer. at depot ITEm dESCrIPTION...
  • Page 36 2-00-06789B Pellet Tailpipe Gasket Pkg of 5 1-00-07381 Pellet Tailpipe Cast 3-00-247237 Door Hinge Weldment Qty. 2 Req. 1-10-08735W Harman Gold Label Pkg of 5 3-90-08540-5 Haman Silver Label Pkg of 5 3-90-04580-5 Spring Latch Qty. 2 Req. 3-31-00927 1-00-00744...
  • Page 37 Advance Service Parts beginning manufacturing date: N/A Ending manufacturing date: Active Pre Serial Number 008360001 Feeder Assembly 24.1 24.2 24.13 24.3 24.4 24.12 24.11 24.10 24.9 24.7 24.6 24.5 24.8 IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement Stocked parts for your appliance please provide model number and serial number.
  • Page 38 Advance Service Parts beginning manufacturing date: N/A Ending manufacturing date: Active Post Serial Number 008360001 Feeder Assembly 25.1 25.12 25.15 25.16 25.14 25.2 25.13 25.3 25.11 25.10 25.9 25.4 25.5 25.8 25.7 25.6 IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement Stocked parts for your appliance please provide model number and serial number.
  • Page 39 Advance Service Parts beginning manufacturing date: N/A Ending manufacturing date: Active IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement Stocked parts for your appliance please provide model number and serial number. All parts listed in this manual may be ordered from an authorized dealer. at depot ITEm description...
  • Page 40 Addendum for Burning Corn and Pellet Fuel Mixture Harman pellet burning, free-standing stoves and inserts have been tested to ASTM E1509 for burning shelled corn in a mixture with wood pellets. The listing approves up to a 50% corn and 50% pellet mixture. Different mixtures of corn will have distinctively different burn characteristics depending upon moisture content and variety.
  • Page 41: Power Failures

    Contact your dealer if you have questions about UPS compatibility with your appliance. harman Surefire 512h battery back-up The 512H connects to a 12 volt deep cycle battery that will run your appliance for up to eight (8) hours. It includes a trickle charge feature that keeps your battery charged when power is available.
  • Page 42 Service & maintenance log date Of Service Performed by description Of Service...
  • Page 44 Proudly Printed On 100% Recycled Paper...

This manual is also suitable for:

Advance

Table of Contents