Horizon Fitness Adventure 2 Plus Owner's Manual
Hide thumbs
Also See for Adventure 2 Plus:
- Owner's manual (13 pages) ,
- Service manual (13 pages) ,
- Assembly manual (6 pages)
Subscribe to Our Youtube Channel
Related Manuals for Horizon Fitness Adventure 2 Plus
Summary of Contents for Horizon Fitness Adventure 2 Plus
- Page 1 Adventure Plus Adventure Plus TREADMILL OWNER’S MANUAL Read the TREADMILL gUIDE before using this OWNER’S MANUAL.
- Page 2 ASSEMBLY WARNING There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the treadmill could have frame parts that are not tightened and will seem loose and may cause irritating noises.
-
Page 3: Tools Included
PRE ASSEMBLY TooLS INCLUDED: TOUCH PAD PANEL AND DISPLAY WINDOWS F 6 mm T-Wrench UNPACKING F 5 mm L-Wrench SPEAKERS F 4 mm T-Wrench (ADVENTURE 3 PLUS ONLY) Place the treadmill carton on a level flat surface. It is recommended that you place a F 4 mm L-Wrench protective covering on your floor. -
Page 4: Assembly Step
ASSEMBLY STEP 1 ASSEMBLY STEP 2 Open hardware bag 1. Lift the runnIng deCK upward until the HARDWARE BAG 1 CONTENTS : HARDWARE BAG 2 CONTENTS : FOOT LaTCh locks. Remove all contents from Cut the yellow banding and get console mast underneath the running deck. - Page 5 ASSEMBLY STEP 3 ASSEMBLY STEP 4 Open hardware bag 3. Disengage the deCK LOCK LaTCh with your HARDWARE BAG 3 CONTENTS : HARDWARE BAG 4 CONTENTS : foot to lower the runnIng deCK. Pull Lead wIre through rIghT COnSOLe BOLT (D) SPRING WASHER (B) FLAT WASHER (C) BOLT (A)
- Page 6 Tighten all console bolts (Step 4) and support bar bolts (Step C above) completely BOLTS (H) adventure 2 plus Max. User Weight: 125 kg / 275 lbs. Product Weight: 85 kg / 187 lbs SUPPORT BAR Overall Dimension: 181 x 86 x 137 cm / 71” x 34” x 54”...
-
Page 7: Treadmill Operation
TREADMILL OPERATION This section explains how to use your treadmill’s console and programming. The BASIC OPERATION section in the TREADMILL gUIDE has instructions for the following: • LoCATIoN oF THE TREADMILL • USING THE SAFETY KEY • FoLDING THE TREADMILL •... - Page 8 ADVENTURE 2 PLUS AND ADVENTURE 3 PLUS CoNSoLE oPERATIoN Note: There is a thin protective sheet of clear plastic on the overlay of the console that should be removed before use. A) * LED DISPLAY WINDoWS: time, distance, calories, heart rate, speed, incline and workout profiles.
-
Page 9: Display Windows
1) Check to make sure no objects are placed on the and incline will need to be from the user in this setting. Adventure 2 Plus and Adventure 3 Plus DISPLAYS belt that will hinder the movement of the treadmill. - Page 10 TARGET PRoFILES TARGET 1 – TIME: Allows user to set a target based on how long they would like to workout. Time targets can range 3) WEIGHT LoSS – ALL MoDELS: Promotes weight loss by increasing and decreasing the speed, while keeping you in your fat from 15:00 –...
-
Page 11: Finishing Your Workout
To RESET THE CoNSoLE Hold STOP key for 3 seconds. CooL DoWN Puts treadmill into cool down mode. Cool down lasts for four minutes and reduces speed and incline to allow your heart to readjust to decreased demand. FINISHING YoUR WoRKoUT When your workout is complete, the monitor display will flash “FINISHED”... - Page 13 TREADMILL OWNER’S MANUAL Adventure 2 Plus & Adventure 3 Plus Treadmill Owner’s Manual 111912’ Rev1.2 © 2012 Horizon Fitness...
Need help?
Do you have a question about the Adventure 2 Plus and is the answer not in the manual?
Questions and answers