Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Vivitek D-220MX
Summary of Contents for Vivitek D-220MX
-
Page 1: User Manual
Portable DLP projector D-220MX User Manual China Projectors Group Room 207, 2/F., Block B, Seaview Estate, Watson Road, North Point, Hong Kong. Telephone: (852) 28875151 Fax: (852) 25031144 E-mail: jng@chinaprojectors.com Website: http://www.chinaprojectors.com... - Page 2 Copyright This publication, including all photographs, illustrations and software, is protected under international copy- right laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. © Copyright June, 2006 Disclaimer The information in this document is subject to change without notice.
- Page 3 — ’ — ’ — ’ Important Safety Information Congratulations on purchasing the DLP projector! Important: It is strongly recommended that you read this section carefully before using the projector. These safety and usage instructions will ensure that you enjoy many years of safe use of the projector. Keep this manual for future reference.
- Page 4 Power Safety Only use the supplied power cord. Do not place anything on the power cord. Place the power cord where it will not be in the way of foot traffic. Remove the batteries from the remote control when storing or not in use for a prolonged period. Replacing the Lamp Replacing the lamp can be hazardous if done incorrectly.
- Page 5 — ’ — ’ — ’ Main Features • Lightweight unit, easy to pack away and transport • Compatible with all major video standards including NTSC, PAL, and SECAM • A high brightness rating allows for presentations in daylight or in lit rooms •...
-
Page 6: Table Of Contents
Table of contents GETTING STARTED ................................1 ................................1 ACKING HECKLIST ............................... 2 IEWS OF ROJECTOR ARTS Front-right View ................................2 Top view—On-screen Display (OSD) buttons and LEDs ....................3 Rear view ..................................4 Bottom view..................................5 (26- )......................... 6 EMOTE ONTROL ARTS... - Page 7 — ’ — ’ — ’ V.S. P ......................... 41 ROJECTION ISTANCE ROJECTION ................................ 42 IMING ABLE ..............................43 ROJECTOR IMENSIONS REGULATORY COMPLIANCE ............................. 44 FCC W .................................. 44 ARNING .................................... 44 ANADA ..............................44 AFETY ERTIFICATIONS EN 55022 W .................................
-
Page 8: Getting Started
ETTING TARTED Packing Checklist The remote control that ships with the projector depends on the model you purchased. Carefully unpack the projector and check that the following items are included: EMOTE CONTROL PROJECTOR WITH LENS CAP WITH TWO BATTERIES OWER CORD CABLE VIDEO CABLE UDIO CABLE... -
Page 9: Views Of Projector Parts
— ’ — ’ — ’ Views of Projector Parts Front-right View ABEL ESCRIPTION EE PAGE See “Top view—OSD buttons and LEDs” on next page Rear IR receiver Receiver for IR signal from remote control Lens zoom Enlarges the projected image Focus Focuses the projected image Height-adjuster button... -
Page 10: Top View-On-Screen Display (Osd) Buttons And Leds
– ’ – ’ – ’ Top view—On-screen Display (OSD) buttons and LEDs ABEL ESCRIPTION EE PAGE Ready LED Orange Lamp ready—you can safely turn on or off the projector Flashing Lamp not ready—do not press the power button Power LED Green Unit is powered on and working correctly Unit is powered off... -
Page 11: Rear View
— ’ — ’ — ’ Rear view ABEL ESCRIPTION EE PAGE Power Connect the supplied power cord Rear IR receiver Receiver for IR signal from remote control Connect the USB cable from a computer Audio-in Connect the audio cable from the input device Video/S-video Connect the composite or S-video cable from a video device... -
Page 12: Bottom View
– ’ – ’ – ’ Bottom view ABEL ESCRIPTION EE PAGE Height-adjuster button Push to release height adjuster Height adjuster Adjusts level of projector Projection lamp cover Remove when changing lamp – 5 –... -
Page 13: Remote Control Parts (26- Button Model )
— ’ — ’ — ’ Remote Control Parts Important: 1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency fluo- rescent lights can disrupt remote control operation. 2. Be sure nothing obstructs the path between the remote control and the projector. If the path be- tween the remote control and the projector is obstructed, you can bounce the signal off certain reflective surfaces such as projector screens. - Page 14 – ’ – ’ – ’ ABEL ESCRIPTION EE PAGE Laser Press to operate the on-screen pointer Up arrow when connected through USB to a PC Right Right arrow when connected through USB to a PC Down Down arrow when connected through USB to a PC Page Down Page down when connected through USB to a PC Up cursor...
-
Page 15: Remote Control Operating Range
— ’ — ’ — ’ ABEL ESCRIPTION EE PAGE Laser Use as on-screen pointer. DO NOT POINT IN EYES. Note: The remote control can only interface with a computer when connected to the computer through a USB cable connection. The computer cable connects a computer to the projector for display pur- poses only. - Page 16 – ’ – ’ – ’ – 9 –...
-
Page 17: Setup And Operation
ETUP AND PERATION Inserting the Remote Control Batteries (26-button Model) Remove the battery compartment cover by sliding the cover in the direction of the arrow. Insert the supplied batteries taking note of the polarity (+/-) as shown here. Replace the cover. Caution: 1. -
Page 18: Connecting Input Devices
– ’ – ’ – ’ Connecting Input Devices A PC or notebook computer as well as video devices can be connected to the projector at the same time. Video devices include DVD, VCD, and VHS players, as well as movie camcorders and digital still cameras. -
Page 19: Starting And Shutting Down The Projector
— ’ — ’ — ’ Starting and Shutting down the Projector Remove the lens cover. Connect the power cord to the projector. Connect the other end to a wall outlet. The POWER and READY LEDs on the pro- jector turn on. Turn on the connected devices. -
Page 20: Setting An Access Password (Security Lock)
– ’ – ’ – ’ Setting an Access Password (Security Lock) You can use the cursor (arrow) buttons to set a password and prevent unauthorized use of the pro- jector. When enabled, the password must be entered after you power on the projector. (See “Navigating the OSD”... -
Page 21: Adjusting The Projector Level
— ’ — ’ — ’ Adjusting the Projector Level Take note of the following when setting up the projector: • The projector table or stand should be level and sturdy. • Position the projector so that it is perpendicular to the screen. •... -
Page 22: Adjusting The Zoom, Focus And Keystone
– ’ – ’ – ’ Adjusting the Zoom, Focus and Keystone Use the Image-zoom con- trol (on the projector only) to resize the projected im- age and screen size Use the Image-focus con- trol (on the projector only) to sharpen the projected image Press the Keystone button on the remote control. -
Page 23: Adjusting The Volume
— ’ — ’ — ’ Adjusting the Volume Press the Volume +/- but- ton on the remote control. The volume control ap- pears on the display. (See page 17 to adjust volume with the Quick Menu but- ton on the projector.) (15-button Model) (26-button Model) Use the Volume +/- but-... -
Page 24: Adjusting With The Projector Quick Menu Button
– ’ – ’ – ’ Adjusting with the Projector Quick Menu Button Use the Quick Menu button on the projector to adjust brightness, contrast, volume, and keystone. Press the Quick Menu button. The brightness control appears on the display. Press the Quick Menu button repeatedly to scroll through the options con-... -
Page 25: On-Screen Display (Osd) Menu Settings
(OSD) M CREEN ISPLAY ETTINGS OSD Menu Controls The projector has an OSD that lets you make image adjustments and change various settings. Navigating the OSD You can use the remote control cursor buttons or the buttons on the top of the projector to navigate and make changes to the OSD. -
Page 26: Setting The Osd Language
– ’ – ’ – ’ Setting the OSD Language You may want to reference the OSD on your projector while reading this section. Set the OSD lan- guage to your preference before continuing. (The default language is English.) 1. Press the Menu button. The Main menu appears. 2. -
Page 27: Main Menu
— ’ — ’ — ’ Main Menu Press the Menu button to open the OSD menu. Press the cursor button to move to the Main button to move up and down in the Main menu. Press menu. Press the cursor to change values for settings, and then press Enter or to confirm the new setting. -
Page 28: Main Menu Functions Available For Connected Source
– ’ – ’ – ’ ESCRIPTION EFAULT Reset Resets all Main settings to default values — Main Menu Functions Available for Connected Source Function Component Video Composite Video S-video Brightness Contrast Sharpness Color Temp Color Saturation Color Tint Gamma Color Space Reset x = available to video source... -
Page 29: Setup Menu
— ’ — ’ — ’ Setup Menu Press the Menu button to open the OSD menu. Press the cursor button to move to the Setup button to move up and down in the Setup menu. Press menu. Press the cursor to change values for settings, and then press Enter or to confirm the new setting. -
Page 30: Advance Feature
– ’ – ’ – ’ Function Component Video Composite Video S-video Keystone correction Aspect Ratio Advance Feature Reset x = available to video source Advance Feature Press the Menu button to open the OSD menu. Press to move to the Setup menu. Press move to the Advance Feature menu and then press Enter or . - Page 31 — ’ — ’ — ’ ESCRIPTION EFAULT Auto When enabled, keystone correction is automatically calibrated when you Keystone press the Auto button on the remote control or the keypad. Press to enable or disable Auto Keystone. AutoKeystone Press Enter or to automatically calibrate keystone correction.
-
Page 32: User Color
– ’ – ’ – ’ User Color Press the Menu button to open the OSD menu. Press to move to the Setup menu. Press move to the Advance Feature menu and then press Enter or to move to the User . -
Page 33: Config Menu
— ’ — ’ — ’ Config Menu Press the Menu button to open the Main menu. Press the cursor button to move to the Config button to move up and down in the Config menu. Press menu. Press the cursor to change values for settings, and then press Enter or to confirm the new setting. -
Page 34: Utility Menu
– ’ – ’ – ’ Utility Menu Press the Menu button to open the Main menu. Press the cursor button to move to the Utility button to move up and down in the Utility menu. Press menu. Press the cursor to change values for settings, and then press Enter or to confirm the new setting. -
Page 35: Utility Menu Functions Available For Connected Source
— ’ — ’ — ’ ESCRIPTION EFAULT Digital Zoom Digital operation for zoom and pan adjustment. Press En- — ter or . The Zoom menu appears. Press to zoom in; press to zoom out. Press Enter or to open the Pan menu. (You must zoom in before you can open the Pan menu.) Use the cursor buttons to pan the zoomed image. -
Page 36: Language Menu
– ’ – ’ – ’ Language Menu Press the Menu button to open the Main menu. Press the cursor button to move to the Lan- guage menu. Press the cursor button to move up and down in the Language menu. Press Enter to confirm the new setting. -
Page 37: Status Menu
— ’ — ’ — ’ Status Menu Press the Menu button to open the Main menu. Press the cursor button to move to the Status button to move up and down in the Status menu. menu. Press the cursor ESCRIPTION EFAULT Video... -
Page 38: Maintenance And Security
AINTENANCE AND ECURITY Replacing the Projection Lamp The projection lamp should be replaced when it burns out. It should only be replaced with a certified replacement part, which you can order from your local dealer. Important: 1. The lamp contains a certain amount of mercury and should be disposed of according to local or- dinance regulations. - Page 39 — ’ — ’ — ’ Remove the two screws from the lamp module (A). Lift the module handle up (B). Pull firmly on the module han- dle to remove the lamp module. Reverse steps 1 to 5 to install the new lamp module.
-
Page 40: Resetting The Lamp
– ’ – ’ – ’ Resetting the Lamp After replacing the lamp, you should reset the lamp hour counter to zero. Refer to the following: Press the Menu button to open the Main menu. Press the cursor button to move to the Status menu. -
Page 41: Cleaning The Lens
— ’ — ’ — ’ Cleaning the Lens You can purchase optic lens cleaner from most camera stores. Refer to the following to clean the pro- jector lens. 1. Apply a little optic lens cleaner to a clean soft cloth. (Do not apply the cleaner directly to the lens.) 2. -
Page 42: Troubleshooting
ROUBLESHOOTING Common problems and solutions These guidelines provide tips to deal with problems you may encounter while using the projector. If the problem remains unsolved, contact your dealer for assistance. Often after time spent troubleshooting, the problem is traced to something as simple as a loose con- nection. -
Page 43: Led Error Messages
— ’ — ’ — ’ LED Error Messages TATUS ESCRIPTION NUMBER OF FLASHES Ready Flashing Lamp not ready—do not press the power button Fan1 error Fan2 error Power System task created error System overheating System interface error Lamp error Fan error (refer to Ready LED status to determine which fan) Lamp cover open DLP driver error... -
Page 44: Lamp Problems
– ’ – ’ – ’ Problem: The image is flat with no contrast Adjust the Contrast setting on the Main menu of the OSD. Problem: The color of the projected image does not match the source image. Adjust the Color Temperature and Gamma settings on the Main menu of the OSD. Lamp Problems Problem: There is no light from the projector 1. -
Page 45: Having The Projector Serviced
— ’ — ’ — ’ Having the Projector Serviced If you are unable to solve the problem, you should have the projector serviced. Pack the projector in the original carton. Include a description of the problem and a checklist of the steps you took when trying to fix the problem: The information may be useful to service personnel. -
Page 46: Specifications
PECIFICATIONS Specifications Display type TI DMD 0.7-inch x 1, 12 degrees, DDR DLP with DDP 2000 ASIC controller Resolution XGA 1024 x 768 native Color 16.7 Million (24-bits/pixel) Bandwidth Up to 140 MHz Weight <1.13 kg (<2.5 lbs.) Projection distance 1.5 to 7 meters (59 to 276 inches) Projection screen size 0.89 to 4.86 meters (35.15 to 191.38 inches) -
Page 47: Input/Output Connectors
— ’ — ’ — ’ Input/output connectors DVI-I Video Mini-jack to composite video (RCAx1) Mini-jack to S-video (Mini-DIN) Audio Mini-jack Security Kensington slot – 40 –... - Page 48 – ’ – ’ – ’ Projection Distance V.S. Projection Size L Projection Distance Max. Screen Size Max. Screen Size (Wide) (Tele) Projection Width Height Width Height Diagonal Diagonal Distance L 1.00 m 0.69 m 0.56 m 0.42 m 0.60 m 0.48 m 0.36 m 3.28 '...
-
Page 49: Timing Mode Table
— ’ — ’ — ’ Timing Mode Table The projector can display several resolutions. The following table outlines the resolutions that can be displayed by the projector. Frequency H. Frequency V. Signal Resolution Video Digital Analog (KHz) (Hz) NTSC 15.734 60.0 Ο... -
Page 50: Projector Dimensions
– ’ – ’ – ’ Projector Dimensions 19.5 cm (7.7 inches) – 43 –... -
Page 51: Fcc Warning
EGULATORY OMPLIANCE FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device pur- suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communica- tions.