Page 2
Important: It is strongly recommended that you read this section carefully before using the projector. These safety and usage instructions will ensure that you enjoy many years of safe use of the projector. Keep this manual for future reference. Symbols Used Warning symbols are used on the unit and in this manual to alert you of hazardous situations.
Page 3
Unplug the power cord before cleaning. See Cleaning the projector on page 77. Allow the lamp to cool for about one hour. Regulatory Warnings Before installing and using the projector, read the regulatory notices in the Regulatory Compliance section on page 104. Symbol Explanations DISPOSAL: Do not use household or municipal waste collection services for disposal of electrical and electronic equipment.
Page 4
Input source automatically detected. About this manual This manual is intended for end users and describes how to install and operate the DLP projector. Wher- ever possible, relevant information—such as an illustration and its description—has been kept on one page. This printer-friendly format is both for your convenience and to help save paper, thereby protecting the environment.
ICTURE DJUSTING THE OCUS ANUALLY Adjusting by Using the OSD Control Panel... 34 ... 35 HANGING Changing Lamp Mode by Using the Projector's OSD Control Panel... 35 ... 36 ETTING NFORMATION DJUSTING OSITION OTAL Adjusting Position/Total Dots/Fine Sync by using the OSD Control Panel... 37 Correcting Keystone by Using the Remote Control ...
Page 6
Network... 74 Version ... 75 ESET ESCRIPTIONS AND MAINTENANCE... 77 ... 77 LEANING THE PROJECTOR Cleaning the Cabinet ... 77 Cleaning the Lens ... 77 Cleaning the Filters ... 78 Replacing the Lamps... 80 Resetting the Lamp Time Counter... 83 APPENDIX...
Page 7
Remote Commands... 96 Set Value Command... 97 Data Range ... 97 Query Command ... 97 Response message... 97 ... 98 CREEN RIGGER HTTP B PERATION SING ROWSER Overview ... 99 Preparation Before Use ... 99 Handling of the Address for Operation by Using a Browser ... 99 Configuring Network Settings...
Packing Checklist Carefully unpack the projector and check that the following items are included: PROJECTOR OWER CORD OWER CORD MODEL HINA MODEL CD-ROM ’ S MANUAL Contact your dealer immediately if any items are missing, appear damaged, or if the unit does not work.
Kensington lock Security chain lock Carrying handle Important: Grill openings on the projector allow for good air circulation, which keeps the projector lamp cool. Do not obstruct any of the grill openings. 9 10 12 13 Remove cover to replace lamp or color wheel...
With ceiling installation, use approved mounting hardware & M4 screws; maximum depth of screw: 12 mm; distance from ceiling/ wall: 20 cm (0.7 feet) for proper ventilation; distance from fluorescent lamps: at least 1 m (3 feet) front and back of the projector. For permanent installations, follow local codes.
Optimize image size, position, and resolution Green / Flashing, See Indicator Messages Select or change settings in the OSD Turn the projector on or off (main power switch must be turned on first). Press to place the projector in standby mode. Detects the input device...
Connect an RCA audio cables (not supplied) from the input device right and left channels Installation control When connected to the screen through a commercially available ca- ble, the screen deploys automatically on start up of the projector. The screen retracts when...
Page 13
— ’ — ’ — ’ ABEL AC IN AUDIO IN [L (MONO)/R] (VIDEO) VIDEO IN COMPONENT IN (Y, Pb/Cb, Pr/Cr) COMPUTER 2 IN (R/Cr, G/Y, B/Cb, H, COMPUTER 1 IN AUDIO IN (COMPUTER 1) SERVICE Note: To use this feature, you must turn on the Screen Trigger function on the OSD. Screen controllers are supplied and supported by screen manufacturers.
2. Be sure nothing obstructs the path between the remote control and the projector. If the path be- tween the remote control and the projector is obstructed, you can bounce the signal off certain reflective surfaces such as projector screens.
Page 15
Note: The remote control can only interface with a computer when connected to the computer through a USB cable connection. The computer cable connects a computer to the projector for display pur- poses only. Navigates and changes settings in the OSD...
Provided you are not holding the remote perpendicular to the sides or the rear of the projector, the remote will function well within a radius of about 7 meters (23 feet) and 15 degrees above or below the projector level. If the projector does not respond to the remote control, move a little closer.
Replace the cover. Caution: 1. Only use AAA batteries. (Alkaline is better). 2. Dispose of used batteries according to local ordinance regulations. 3. Remove the battery when not using the projector for prolonged periods. ETUP AND – 10 – PERATION...
Work on a level surface with a soft cloth under it to avoid scratching. If you remove and store the lens, attach the lens cap to the projector to keep off dust and dirt. Removing the Existing Lens From the Projector Pull out the lens cap.
’ Caution: When installing the lens into the projector, be sure to remove the lens cap from the back of the op- tional lens before installing the optional lens into the projector. Failure to do so will cause damage to the projector.
Throw Distance and Screen Size Example of GB940G: The further your projector is from the screen or wall, the larger the image. The minimum size the im- age can be is approximately 40 inches (1 m) measured diagonally when the projector is roughly 65 inches (1.7 m) from the wall or screen.
Page 21
Ceiling installation must be done by a qualified professional. Contact your dealer for more informa- tion. It is not recommended you install the projector yourself. Only use the projector on a solid, level surface. Serious injury and damage can occur if the projec- tor is dropped.
Installing the Optional Color Wheel The projector comes with a four-segment color wheel installed. An additional six-segment color wheel is optional. To replace the color wheel (located under the lamp cover adjacent to lamp 1) refer to the following guide.
Page 23
— ’ — ’ — ’ Insert the six-segment color wheel Close the lamp cover and secure the retaining screws as shown. Align the lamp cover in the direction of the arrow (B) and slide it into place. Secure the captive screw (A). Storing Unused Color Wheel: Keep the unused color wheel in the zipper bag in which the 6-segment color wheel (not supplied) was packaged.
To connect a PC or Macintosh computer to the projector, refer to the following guide. 1. Connect a computer to the projector through one of the three available input data connections before turning on the PC or the projector. The best signal order (from best to least suitable) is as follows: Computer 3 in (see Terminal Panel Features on page 5) is a digital signal and offers the best connection to your computer.
Failure to follow the above steps may not activate the digital output of the graphics card resulting in no picture being displayed. Should this happen, restart your PC. Connecting an External Monitor Connect an external monitor to the projector through RGB out connections as shown below (see Terminal Panel Features on page 5). – 18 –...
Connecting Your DVD Player with Component Output To connect a DVD Player to the projector, refer to the following guide. 1. Connect the DVD Player to the projector as shown below before turning on the Player or the pro- jector.
— ’ — ’ — ’ Connecting Your VCR or Laser Disc Player To connect your VCR or Laser Disc Player, refer to the following diagram. Note: Refer to your VCR or laser disc player user’s manual for more information about your device’s re- quirements.
ROJECTING AN Turning on the Projector Once the projector is correctly located and the power cable and other connections are in place, it is important that the projector is powered on correctly in order to avoid damage to components and un- necessary wear and tear.
’ Note on Startup Screen (Menu Language Select screen) In the first instance of powering on the projector, the language menu is displayed to select the default language. Select the required default language using the ▲ or ▼ buttons on the OSD menu panel or the remote...
Selecting an Input Source The Input Source can be selected from the projector's control panel or from the remote control unit. Refer to the following guide to select the Input Source. Press Menu on the OSD control panel or on the remote control unit to display the Main Menu.
Refer to the following guides to adjust Picture Position manually. Adjusting Picture Position Manually Press the Lens Shift keypad on the projector in any direction to bring up the Lens Shift window. Press the directional key as re- quired to shift the image.
The Screen window is displayed. Select the desired picture size us- ing ▲or▼ and press When finished, press Cancel to return to the projected image. Lens Shift Adjustable Range The adjustable range for lens shift is tabulated below and subject to the conditions listed. Note: The drawings below apply to the standard lens (GB940G) only.
— ’ — ’ — ’ From the Remote Control Unit Press Menu and select the Set- ting menu using ▲or▼. Press to open the Setting menu. Press ◄or► to select Basic fol- lowed by ▲or▼ to select Lens Shift. Press The Lens Shift window displays.
Page 34
To alter the picture size, press Menu and select the Adjust menu using ▲or▼. Press open the Adjust menu. Press ◄or► to select Image Options followed by ▲or▼ to select Screen. Press Select the desired picture size using ▲or▼ and press When finished, press Menu to return to the projected image.
— ’ — ’ — ’ Adjusting the Projector Level To raise the level of the projector, twist the adjusters clockwise. To lower the level of the projector, lift the projector and twist the adjusters counter clockwise. – 28 –...
– ’ – ’ – ’ Optimizing an RGB Image Automatically Adjusting the Image Using AUTO To optimize an RGB image automatically refer to the following guide. Press the Auto button on the remote control (see Remote Control Parts on page 7) or the AUTO but- ton on the OSD control panel to optimize an RGB image automatically.
— ’ — ’ — ’ Adjusting Volume Up and Down The volume can be adjusted from the OSD Control Panel or with the Remote Control unit. Refer to the following as a guide. Press the Volume +/- buttons on the remote control or the ◄...
Do not unplug the power cable from the wall outlet or projector when the projector is powered on. Doing so can cause damage to the AC IN connector of the projector and (or) the prong plug of the power cable. To turn off the AC power supply when the projector is powered on, use a power strip equipped with a switch and a breaker.
’ About Direct Power Off The projector has a feature called "Direct Power Off". This feature allows the projector to be turned off (even when projecting an image) using a power strip equipped with a switch and a breaker. Note: Before using Direct Power Off, be sure to allow at least 20 minutes immediately after turning on the projector and starting to display an image.
3. To resume projection, press the Blank button once more. Note: For extended periods of time it is recommended that the projector be powered off. Freezing a Picture The projected image can be frozen for short periods of time by using the remote control. This feature is useful for capturing still images from movies or freezing an animation at a particular point.
— ’ Adjusting the Focus/Zoom Manually The focus and zoom can be adjusted manually from the projector focus/zoom panel. Refer to the fol- lowing guides to adjust the focus and zoom manually. Adjusting by Using the OSD Control Panel Press the Focus or Zoom...
Changing Lamp Mode The projector has two lamp modes available, Normal and Eco. The Normal mode is used for every- day standard projection, whereas the Eco mode is used for saving power and lamp life. To change the Lamp Mode, refer to the following guides.
— ’ Getting Information The Information screen provides details on the life of consumable items within the projector as well as other information such as software version. To access the Information screen, refer to the following guide. Press Menu on the projec-...
Adjusting Position/Total Dots/Fine Sync The Position/Total dots/Fine sync and Keystone Correction can be adjusted manually from the p jector's control panel or from the remote control unit. Refer to the following guides to adjust the Keystone Distortion manually. Adjusting Position/Total Dots/Fine Sync by using the OSD Control Panel Press the Menu button to display the Main menu.
— ’ Correcting Keystone by Using the Remote Control Important: When adjusting the keystone, place the projector in the following position. Horizontal: set to the lens center Vertical: set to the maximum top Press the Keystone button to display the Keystone window.
Page 46
DJUSTMENT Keystone The following are conditions under which the maximum angle is achieved: When the standard lens (GB940G) is used When the lens shift is set to H for center and V for 0.5 shift. When the lens shift is used and yet you do not get the above-mentioned condition (H for center and V for 0.5 shift), you cannot adjust the lens shift correctly.
Preventing the Unauthorized Use of the Projector The projector has a built-in security feature to lock the OSD control panels and deny remote control operation. The security feature has no default keyword; in the first instance of enabling the security feature, the user must define a keyword.
Caution: When you have set or changed the PIN code, take a memo and keep it securely. If you forget your PIN code, the projector can no longer be started. Contact your dealer or the service center. Unlocking the Projector To unlock the projector, refer to the following guide.
— ’ — ’ — ’ Using the Physical Lock Using the Kensington Lock If you are concerned about security, attach the projector to a permanent object with the Kensington slot and a security cable. – 42 –...
Navigating the OSD You can use the remote control or the buttons on the top of the projector to navigate and make changes to the OSD. The following illustration shows the corresponding buttons on the remote control and on the projector.
Page 51
— ’ — ’ — ’ Press the cursor ◄ or ► button to move through secondary menus. Press ▲or▼ to select menu items and ◄or► to change values for settings. Press to confirm the new setting. Press Cancel or Menu to close the OSD or leave a submenu.
Menu Elements Some menus and windows contain large amounts of information in a small area. Refer to the follow- ing guide to navigate through options more easily. Title Title Radio button Menu windows or dialog windows typically contain the following elements: ABEL Title Highlight...
— ’ — ’ — ’ Input Menu Descriptions and Functions The Input menu displays all supported image sources. Select the required source from the menu using ▲ or ▼ and press ABEL Select the source connected to the Computer 1 input Computer 1 (see Connecting Your PC or Macintosh Computer on page 17).
Adjust Menu Descriptions and Functions The Adjust menu contains overall projector settings for image output such as sharpness, overscan and color matrix. Three tabs are accessible through the Adjust menu, Image, Image Options and Video. Image menu The Image tab is used to alter picture settings and can be accessed from the Adjust menu.
— ’ — ’ — ’ Image options menu The Image Options tab is used to configure image options such as screen positioning and aspect ra- tio. Access the Image Options tab in the Adjust menu. The following table lists all functions with a description and the default setting. ABEL Screen Select Screen using ◄or►...
Page 58
– ’ – ’ – ’ Screen The Screen option allows for the adjustment of the aspect ratio to alter the appearance or ratio of the projected image. 4:3 – Standard TV screen (4:3), proportionally four units wide for every three units high, no matter the size of the screen.
— ’ — ’ — ’ Video menu The Video tab is used to configure image options such as film. Access the Video tab in the Adjust menu. The following table lists all functions with a description and the default setting. A detailed description follows the table.
Page 60
Noise reduction Select the level of noise reduction required. Range: Off, Low, Mid, High. 3D Y/C separation 3D Y/C Separation separates composite signal to Y (brightness) signal and C (color) signal, and can help to produce clearer and sharper images without overlapping colors (rainbow effect). Set 3D Y/C Separation On or Off.
Page 61
— ’ — ’ — ’ Color matrix Color Matrices define the amount of the three-color components R (red), G (green), and B (blue) in a single point in color space. Select from the following: Auto – Auto selects the color matrix. RGB –...
Detail Setting Menu Descriptions and Functions The Detail setting menu contains basic and advanced color adjustment options such as gamma cor- rection, color contrast and color correction. Basic The Basic tab contains general setting such as gamma correction and color temperature. Access to the Basic tab is through the Detail setting menu.
Page 63
Select from the following: Dynamic – Allows the projector to alter the gamma correction automatically. Natural – Attempts to emulate the original source as closely as possible. Black detail – Black detail highlights boundaries between light and dark areas of the image more clearly.
White balance White Balance allows the projector to compensate for different colors of light being emitted by differ- ent light sources. The following table lists all functions with a brief description. ABEL Set the value to compensate for red light sources.
— ’ — ’ — ’ Color correction The Color correction tab enables the adjustment of color values in an image to remove unwanted effects, improve color, characteristics or add more of a particular color. The following table lists all functions with a brief description. ABEL Increase or decrease the amount of red in the projected output using ◄...
Setting Menu Descriptions and Functions The Setting menu contains the most often used settings during installation and options to customize the general output of the projector. Three tabs are accessible through the Setting menu, Basic, In- stallation and Option. Basic The Basic tab contains general setup options such as lamp mode and OSD language settings and can be accessed with the projector control panel or with the remote control unit.
Page 67
Select Horizontal or Vertical using ▲or▼ then, use ◄or► to adjust the projected image appearance as required. Note: When adjusting the keystone, place the projector in the following position. Horizontal: set to the lens center Vertical: set to the maximum top Lamp control Select Normal or Eco from the lamp mode window.
Page 68
Lamp interval The period of time for regulating lamp usage when not in dual lamp mode. Select from the following: Off, 1 week, 4 weeks and 2000H Language Select the OSD language to be used. Select from the following: English German French Italian...
This Control Panel Lock does not affect the remote control functions. When the control panel is locked, pressing and holding the Cancel but- ton on the projector cabinet for about 10 seconds. The setting will change to Off. – 62 –...
Page 70
Select from the following: Desktop Front – Standard forward facing projection (Default setting). Desktop Rear – Standard rear projection. Enables the projector to produce the image from behind the screen by reversing the image. Ceiling Front – Forward facing ceiling mounted projection. Enables ceiling mounted projection by in- verting the image.
Page 71
Background enables you to display a blue/black screen when there is no signal. The default back- ground is blue. Select from the following: Blue Black Logo PIN Code Lock See Preventing the Unauthorized Use of the Projector on page 40. – 64 –...
Page 72
Turn On/Off the Key Lock function for cabinet buttons. Note: This Control Panel Lock does not affect the remote control functions. When the control panel is locked, press and holding the Cancel button on the projector cabinet for about 10 seconds. The setting will change to Off. DynamicBlack DynamicBlack enables you to improve the black level of the projector.
Page 73
The MONITOR OUT function is not available during Power-saving mode. Control through the PC Control connector and Network mode is not available during Power-saving mode. For PC control and Network mode of the projector it is recommended to leave the projector in the Normal mode.
Network setting The Network setting menu is accessed by using the Setup/Installation menu and contains the general LAN settings. The following table lists all functions with a description and the default setting. ABEL Select either a static IP (Disable) or DHCP IP (Enable) setting by selecting the DHCP appropriate radio button.
S-Video— select the S-Video Color System from Auto, NTSC, PAL, and SECAM. This option turns on or off messages. Message Range: Off or On Set this item to on to have the projector display a message when the air filter Filter warning needs servicing. Range: Off, 100[H], 200[H], 500[H], 1000[H] This feature sets the Auto Adjust mode.
Page 76
Power management Power management enables the projector to automatically turn off if there is no signal received by any input. Select from the following: 5 minutes 10 minutes 20 minutes 30 minutes Screen trigger Set Screen trigger to On to enable the projector to automatically lower the projection screen when powering on.
Page 77
— ’ Default input select The Default input is the image source that the projector will search for automatically on startup. Last – Uses the most recently used image source. Auto – Auto detects the default image source. Computer1/2/3 – Uses Computer1, 2 or 3 as the default image source.
Page 78
– ’ Filter warning Set Filter warning to have the projector display a message when the air filter needs servicing. The message below shows when this function is activated. Search mode This feature sets the Auto Adjust mode so that the RGB image can be automatically or manually ad- justed for noise and stability.
Displays the Lamp1 total usage in hours. Lamp2 time Displays the Lamp2 total usage in hours. PJ time Displays the projector total usage in hours. Filter time Displays how many hours the filter has been used. – 72 – ESCRIPTION...
Input The Input tab displays various source and frequency values at a glance. The following table lists all items with a description. ABEL Displays the Input Terminal that is presently being used Input name (see Signal Displays the Source name of the signal presently being used. H-sync.
Version The Version tab displays all the version and product details of the projector and associated software (for display only). The following table lists all items with a description. ABEL Model name Displays Product ID. Firmware Displays Firmware version and Color Wheel currently installed (4-seg or 6-seg).
— ’ — ’ — ’ Reset Menu Descriptions and Functions Occasionally, circumstances may require that factory defaults be reset, for demonstration purposes for example, or when components are replaced. The Reset menu contains options for returning settings to the factory default and is accessed by us- ing the Main menu.
1. Wipe off dust with a clean dampened cloth. 2. Moisten the cloth with warm water and mild detergent and wipe the cabinet. 3. Rinse all detergent from the cloth and wipe the projector again. Caution: To prevent discoloration or fading of the case, do not use abrasive alcohol-based cleaners.
’ Cleaning the Filters The projector uses three filters to keep the fans free of dust and other particles, and should be cleaned every 500 hours of operation. In dusty environments, it is recommended to clean the filters more frequently. If the filter is dirty or clogged, your projector may overheat. When the message be- low is displayed, the filters must be cleaned.
Page 86
Lift the filter foams from all three filteholders in the direction shown. Remove them completely from each filterholder and discard. Place a replacement foam and press down firmly Replace the filter holders by push- ing gentlyin the direction shown. Once the filters are cleaned, please reset the filter hours by using the Clear filter time option in the Reset Menu Descriptions and Functions on page 76.
1. Lamps are positioned differently. Take care not to force the lamps when replacing. 2. Installation of both lamp modules (Lamp 1 and Lamp 2) is required to operate the projector in dual or single lamp mode. If only a single lamp module is installed, the projector's lamp will not turn on and will appear as a lamp failure.
Page 88
Avoid touching the glass surface of the new lamp: Doing so may shorten its operation life. Warning: Be sure to turn off and unplug the projector at least 30 minutes before replacing the lamp. Failure to do so could result in a severe burn.
Page 89
— ’ — ’ — ’ Pull firmly on the module handle in the direction shown to remove the lamp. Reverse steps 1 to 3 to install the new lamp module(s) and re- place the lamp cover. – 82 –...
Resetting the Lamp Time Counter After replacing the lamp(s), the lamp hour counter(s) should be reset to zero. Refer to the following guide: Press the Menu button on the OSD control panel or Remote Control to open the Main menu. Press the ▲or▼...
Several indicator messages are used by the projector to alert users of problems with setup or internal parts. The LEDs on the top surface of the projector show the status of the WARNING and lamp 1/2 as well as the general working order of the projector through the WARNING LED (see OSD Controls and Status LEDs on page LEDs.
Green on Common Problems and Solutions These guidelines provide tips to deal with problems you may encounter while using the projector. If the problem remains unsolved, contact your dealer for assistance. Often the problem is something as simple as a loose connection. Check the following before proceed- ing to the problem-specific solutions.
2. Ensure the power source is good by testing with another electrical device. 3. Restart the projector in the correct order and check that the Power LED is green. 4. If you have replaced the lamp recently, try resetting the lamp connections.
Having the Projector Serviced If you are unable to solve the problem, you should have the projector serviced. Pack the projector in the original carton. Include a description of the problem and a checklist of the steps you took when trying to fix the problem.
Projector Specifications This section provides technical information about the projector's performance. Optical Specifications Projection system Single DLP Resolution 1024 x 768 pixels* (up to UXGA @ 60 Hz) Lamp 280 W AC (230 W in Eco mode), Dual lamp system 50"...
— ’ — ’ — ’ Mechanical Specifications 20" (W) x 7.7" (H) x 15.3" (D) Dimensions 508 mm (W) x 195 mm (H) x 389 mm (D) (not including protrusions) Weight 37.5 lb/17 kg Environmental Considerations Operational Temperatures 41° Storage Temperatures 14°...
— ’ — ’ — ’ Pin Assignments of Mini D-Sub 15 Pin Input Connector Signal Levels Video signal: 0.7Vp-p (Analog) Sync signal: TTL level UMBER Green or Sync on Green Blue Ground Ground Red Ground Green Ground Blue Ground No Connection Sync Signal Ground No Connection...
Compatible Input Signal List The following table shows compatible signal types, their resolution and frequency refresh rates. Horizontal: 15kHz, 31kHz to 90 kHz Vertical: 50 Hz to 85 Hz IGNAL ESOLUTION 640X350 VESA(DMT) 640X350 720X350 CGA84 640X400 VESA(DMT) 640X400 720X400 VESA(DMT) 720X400 720X400...
Page 101
1080p 1080p Note: An image with higher or lower resolution than the projector’s native resolution (1024 x 768) will be compressed. Some Composite and Sync on Green signals may not be displayed correctly. Signals other than those specified in the table above may not be displayed correctly. If this should happen, change the refresh rate or resolution on your PC.
2. Jumper “Request to Send” and “Clear to Send” together on both ends of the cable to simplify the cable connection. 3. For long cables, it is recommended to set communication speed within projector menus to 9600 bps. – 95 –...
ASCII ‘~’ Control Sequence The projector may send a return code after it received a command. If the command isn’t received correctly, the projec- tor will not send the return code Operation Commands The operation commands execute the basic operation setting of this projector.
Set Value Command ITEM ASCII ~ s B ? CR ※ Brightness Contrast ~ s C ? CR Color(Saturation) ~ s R ? CR Tint ~ s N ? CR Scaling ~ s A ? CR Color Temperature ~ s T ? CR Projection Mode ~ s J ? CR ※...
’ Screen Trigger When the projector is powered ON the screen trigger output sends a low voltage trigger to the screen controller and the screen will go down. When the projector is powered OFF the screen trigger stops sending a low voltage trigger to the screen controller and the screen will go up.
Regarding the actual address that is entered for the address or entered to the URL column when op- eration of the projector is via a browser, the host name can be used as it is when the host name corresponding to the IP address of the projector has been registered to the domain name server by a network administrator, or the host name corresponding to the IP address of the projector has been set in the “HOSTS”...
Sender's Address: Specify the sender’s address. Up to 60 alphanumeric and symbols, characters can be used. SMTP Server Name: Type in the SMTP server name to be connected to the projector. Up to 60 al- phanumeric characters can be used.
Page 108
PJLink is a standardization of protocol used for controlling projectors of different manufacturers. This standard protocol is established by Japan Business Machine and Information System Industries As- sociation (JBMIA) in 2005. The projector supports all the commands of PJLink Class 1. ROJECTOR NPUT...
— ’ — ’ Structure of the HTTP Server Once the projector is connected to a network and configured correctly, the following screen is dis- played through the web browser. http:// <the projector's IP address> /index.html UNCTION POWER Panel VOLUME Panel ▲...
Page 110
Error Status – Displays the status of errors occurring within the projector Note: The functions that can be controlled will vary depending on the signal being input to the projector (see Selecting an Input Source on page ETTING for more information).
FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device pur- suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communica- tions.