Related Manuals for Zephyr Milano Island ZML-M90AG
Summary of Contents for Zephyr Milano Island ZML-M90AG
- Page 1 Milano Island ZML-M90AG/AS ZML-E42AG/AS Model number: Serial Number: FEB09.0301 © Zephyr Corporation...
- Page 2 www.zephyronline.com...
- Page 3 SAFETY NOTICE ..............LIST OF MATERIALS ............INSTALLATION Ducting Calculation Sheet ........Mounting Height & Clearance ........ Ducting Options ............Hood Specifi cations ........... Mounting the Hood 9 - 10 ............. Ductless Recirculation ..........CONTROLS 12-14 ..................MAINTENANCE Hood and Filter Cleaning .........
- Page 4 www.zephyronline.com READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE. WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: a.
- Page 5 WARNING TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK. CAUTION To reduce risk of fi re and to properly exhaust air outside - Do not vent exhaust air into spaces within walls, ceilings, attics, crawl spaces or garages. OPERATION Always leave safety grilles and fi...
- Page 6 www.zephyronline.com MODELS: ZML-M90AS, ZML-M90AG, ZML-E42AS, ZML-E42AG PARTS SUPPLIED 1 - Top support frame 2 - Top duct covers 2 - Thick trim pieces 1 - Bottom support frame 2 - Bottom duct covers 2 - Thin trim pieces 1 - 6” round damper, pre-installed 1 - Hood body 1 - Hardware package 1 - Canopy, glass or stainless steel...
- Page 7 Equivalent number Equivalent number Duct pieces Duct pieces length x used T otal length x used T otal 3- 1/ 4” x 10” 1 Ft. 6”- 8” Round 30 Ft. Rect., wall cap straight with damper 7” Round, 1 Ft. 6”- 8”...
- Page 8 www.zephyronline.com Minimum mount height between range top to hood bottom should be no less than 28”. Maximum mount height should be no higher than 36”. Min. ducted 28” Min. recirc. 28” Max. 38” It is important to install the hood at the proper mounting height.
- Page 9 WARNING FIRE HAZARD NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside, unless using the recirculating option. Use single wall rigid Metal ductwork only. Fasten all connections with sheet metal screws and tape all joints w/ certifi...
- Page 10 www.zephyronline.com front of hood side of hood 10 13/16” 10 3/8” min. ducted - 28” min. recirc. - 28” max. - 38” (blower housing) 26” 23 15/16” 35 7/16” or 41 15/16” top of hood (blower housing & ceiling bracket) 8 1/4”...
- Page 11 Top Support Frame Ceiling Joists FIG. B Wood Blocking Top Support Frame Bottom Support Frame Bottom Support Frame back 2. Key hole FIG. C 1. Wider cut out Hood/Canopy front FIG. A CAUTION: At least two installers are required due to the weight and size of the hood.
- Page 12 www.zephyronline.com cut-down canopy Top support frame Thick trim piece Top duct covers (Bottom of the hood) Thin trim piece Bottom duct covers Bottom support frame screw holes (4) for the canopy FIG. E FIG. D 7. Install electrical and duct work. Seal duct work with aluminum duct tape. 8.
- Page 13 Ductless recirculation is intended for applications where an exhaust duct work is not possible to be installed. When converted, the hood functions as a recirculating hood rather than an exhaust hood. Fumes and exhaust from cooking are drawn and fi ltered by a set of optional charcoal fi lters. The air is then purifi ed and re- circulated back within the home.
- Page 14 www.zephyronline.com Blower On/Off Display (speed level, delay off, filter clean/change) Lights On/Dim/Off Adjust 6 Speed Levels 15 Min Delay Off 1. Blower On/Off By pressing the blower is switched on and off. When switched on, the blower starts up on speed level 3. 2.
- Page 15 Charcoal Filter Change Reminder (charcoal filter, if installed) When your hood is installed as a recirculating unit, it is fitted with a set of charcoal filters to purify exhaust and fumes from cooking, then re-circulates the air within the home. These charcoal filters are required to be replaced after every 120 hours of use.
- Page 16 www.zephyronline.com Metal Filter Clean Reminder (metal mesh filter) Whether your hood is installed as an exhaust or purifying unit, a set if metal mesh filters are fitted by the factory, These metal mesh filters are intended to filter out residue from cooking. They need not be replaced on a regular basis but are required to be kept clean.
- Page 17 SURFACE MAINTENANCE: Clean periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent , or steel wool/scouring pads which will scratch and damage surface. For heavier soil use liquid degreaser. After cleaning it is recommended that you use non-abrasive stainless steel polish/cleaners, to polish and buff out the stainless luster and grain.
- Page 18 If bulbs are diffi cult to turn due to prolonged use, fi rmly attach a glass suction cup approximately the diameter of the bulb or use a rubber/latex glove and turn counter clockwise. Replacement bulbs are available at specialty lighting stores. Purchase type GU-10 50W halogen. For Zephyr part numbers please turn to page 18 of the manual. of the...
- Page 19 TROUBLESHOOTING PROCEDURES FOR MILANO ISLAND Issue Cause What to do After installation, 1. The power source is not turned ON. 1. Make sure the circuit breaker and the unit’s the unit doesn’t power is ON. work. 2. The power line and the cable locking connector 2.
- Page 20 www.zephyronline.com DESCRIPTION PART# Replacement Parts Light Bulb GU10 50W (each) Z0B-0020 Metal Filter (each) 50200011 Optional Accessories Recirculating Kit ZRC-0190 Replacement Charcoal Filter (each) Z0F-C002 Duct Cover Extension Z1C-02ML To order parts, visit us online at http://store.zephyronline.com or call us at 1.888.880.8368...
- Page 21 Zephyr Corporation (referred to herein as “we” or “us”) warrants to the original consumer purchaser (referred to herein as “you” or “your”) of Zephyr products (the “Products”) that such Products will be free from defects in materials or work- manship as follows: Two Year Limited Warranty for Parts: For two years from the date of your original purchase of the Products, we will provide, free of charge, Products or parts to replace those that failed due to manufacturing defects.