Toshiba PSL3 User Manual
  1. Manuals
  2. Brands
  3. Toshiba Manuals
  4. Laptop
  5. PSL3
  6. User manual

Toshiba PSL3 User Manual

Satellite l30 / satellite pro l30 series
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
TOSHIBA Satellite L30 /
Satellite Pro L30 Series
User's Manual

Advertisement

Table of Contents
loading

Related Manuals for Toshiba PSL3

Summary of Contents for Toshiba PSL3

  • Page 1 TOSHIBA Satellite L30 / Satellite Pro L30 Series User's Manual...
  • Page 2 TOSHIBA Satellite L30 / Satellite Pro L30 Series Copyright © 2006 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.

  • Page 3: Fcc Information

    Other trademarks and registered trademarks not listed above may be used in this manual. FCC information Product Name: TOSHIBA Satellite L30 / Satellite Pro L30 Series Model number: PSL3 FCC notice “Declaration of Conformity Information” This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.

  • Page 4: Fcc Conditions

    Only peripherals complying with the FCC class B limits may be attached to this equipment. Operation with non-compliant peripherals or peripherals not recommended by TOSHIBA is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer’s external monitor port, USB port, serial port,...
  • Page 5 Note that Canadian Department of Communications (DOC) regulations provide, that changes or modifications not expressly approved by TOSHIBA Corporation could void your authority to operate this equipment. This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

  • Page 6: Type Of Service

    TOSHIBA Satellite L30 / Satellite Pro L30 Series Spain ATAAB AN005, 007, 012, and ES01 Switzerland ATAAB AN002 All other countries/ ATAAB AN003, 004 regions Specific switch settings or software setup are required for each network, please refer to the relevant sections of the user guide for more details.

  • Page 7: If Problems Arise

    FCC. In the event repairs are ever needed on your modem, they should be performed by TOSHIBA Corporation or an authorized representative of TOSHIBA Corporation.
  • Page 8 TOSHIBA Satellite L30 / Satellite Pro L30 Series Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.
  • Page 9 TOSHIBA Satellite L30 / Satellite Pro L30 Series Notes for use of this device in New Zealand ■ The grant of a Telepermit for a device in no way indicates Telecom acceptance of responsibility for the correct operation of that device under all operating conditions.

  • Page 10: General Conditions

    TOSHIBA Satellite L30 / Satellite Pro L30 Series ■ When used in the Auto Answer mode, the S0 register must be set with a value of 3 or 4. This ensures: ■ a person calling your modem will hear a short burst of ringing before the modem answers.

  • Page 11: Optical Disc Drive Safety Instructions

    TOSHIBA Satellite L30 / Satellite Pro L30 Series The charge for a Telepermit assessment is $337.50. An additional charge of $337.50 is payable where an assessment is based on reports against non-Telecom New Zealand Specifications. $112.50 is charged for each variation when submitted at the same time as the original.
  • Page 12 TOSHIBA Satellite L30 / Satellite Pro L30 Series TEAC CD-ROM Drive CD-224E ■ The CD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location.
  • Page 13 TOSHIBA Satellite L30 / Satellite Pro L30 Series TEAC CD-RW/DVD-ROM Drive DW-224E ■ The CD-RW & DVD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location.
  • Page 14 TOSHIBA Satellite L30 / Satellite Pro L30 Series Hitachi-LG Data Storage, Inc. CD-RW/DVD-ROM Drive GCC-4244 ■ The CD-RW & DVD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location.
  • Page 15 TOSHIBA Satellite L30 / Satellite Pro L30 Series TOSHIBA SAMSUNG STORAGE TECHNOLOGY CD-RW/DVD-ROM Drive TS-L462C ■ The CD-RW & DVD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location.
  • Page 16 TOSHIBA Satellite L30 / Satellite Pro L30 Series Panasonic DVD-ROM & CD-R/RW Drive UJDA770T ■ The DVD-ROM & CD-R/RW drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location.
  • Page 17 TOSHIBA Satellite L30 / Satellite Pro L30 Series International precautions CAUTION: This appliance contains a laser system and is classified as a "CLASS 1 LASER PRODUCT." To use this model properly, read the instruction manual carefully and keep this manual for your future reference.
  • Page 18 TOSHIBA Satellite L30 / Satellite Pro L30 Series OBS! Apparaten innehåller laserkomponent som avger laserstråining överstigande gränsen för laserklass 1. VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S...

  • Page 19: General Precautions

    TOSHIBA Satellite L30/ Satellite Pro L30 Series General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigours of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer.
  • Page 20 For optimum performance, use your computer product only under recommended conditions Read additional restrictions under "Environmental Requirements" in appendix A, Specifications. Contact TOSHIBA Technical Service and Support for more information. User’s Manual...

  • Page 21: Working Environment

    EMC (Electromagnetic Compatibility) and safety standards. However, TOSHIBA cannot guarantee that this product still observes these EMC standards if options or cables not produced by TOSHIBA are connected or implemented. In this case the persons who have connected / implemented those options / cables have to provide assurance that the system (PC plus options / cables) still fulfils the required standards.

  • Page 22: Wireless Lan And Your Health

    Because Wireless LAN products operate within the guidelines found in radio frequency safety standards and recommendations, TOSHIBA believes Wireless LAN is safe for use by consumers. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature.

  • Page 23: Limitation Of Liability

    General Precautions Limitation of Liability For damage occurring due to an earthquake or thunder, fire beyond our responsibility, action by third party, other accident, intentional or accidental mistakes by a user, misuse, use under abnormal conditions, we do not take any responsibility.
  • Page 24 General Precautions WARNING Turn OFF the Wireless Communication switch of Wireless Products in a congested place, such as a crowded commuter train. Keep this product away from a cardiac pacemaker at least 22cm. Radio waves can potentially affect cardiac pacemaker operation, thereby causing respiratory troubles.

  • Page 25: Table Of Contents

    TOSHIBA Satellite L30/ Satellite Pro L30 Series Table of Contents Preface Manual contents ......... xxxi Conventions .
  • Page 26 Disclaimer (DVD-ROM & CD-R/RW drive) .....4-8 TOSHIBA Direct Disc Writer ....... . .4-9 Media care.
  • Page 27 Table of Contents Modem ..........4-11 Region selection .
  • Page 28 Table of Contents Maximizing battery operating time ......6-9 Retaining data with power off ......6-10 Extending battery life .
  • Page 29 TOSHIBA support ........
  • Page 30 Table of Contents User’s Manual...

  • Page 31: Preface

    This manual tells how to set up and begin using your TOSHIBA Satellite L30 / Satellite Pro L30 Series computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.

  • Page 32: Conventions

    Preface Chapter 4, Operating Basics, includes instructions on using the following devices: TouchPad, Sound System, optical media drives, modem, wireless communication and LAN. It also provides tips on care of the computer, and CD/DVDs. Chapter 5, Keyboard, describes special keyboard functions including the keypad overlay and hot keys.

  • Page 33: Key Operation

    Preface Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C.
  • Page 34 Preface xxxiv User’s Manual...

  • Page 35: Introduction

    Some of the features described in this manual may not function properly if you use an operating system that was not pre-installed by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use.

  • Page 36: Software

    ■ TOSHIBA Hotkey Utility ■ TOSHIBA User's Manual ■ TOSHIBA Assist* ■ TOSHIBA ConfigFree* ■ TOSHIBA Touch and Launch* ■ TOSHIBA Power Saver Utility* ■ TOSHIBA TouchPad On/Off Utility ■ TOSHIBA PC Diagnostic Tool* ■ TOSHIBA Zooming Utility* Other software may preinstalled dependant on the model purchased.

  • Page 37: Features

    Introduction Features Processor Built-in ® ® Intel Celeron M processor 360J or higher Chipset ® ® Radeon Xpress 200M Memory Main Memory Part of the main system memory may be used by Disclaimer the graphics system for graphics performance and therefore reduce the amount of main system memory available for other computing activities.
  • Page 38 Introduction Disks Hard disk Disclaimer 1 Gigabyte (GB) means 10 = 1,000,000,000 bytes using powers of 10. The computer operating system, however, reports storage capacity using powers of 2 for the definition of 1 GB = 2 = 1,073,741,824 bytes, and therefore shows less storage capacity.

  • Page 39: Pointing Device

    Introduction CD-ROM Drive Some models are supplied with a full size CD- ROM drive, that lets you play CD-ROMs without using an adaptor. CD-ROMs are read at a maximum speed of 24x. The drive supports the following formats: ■ CD-Text ■...
  • Page 40 Introduction Ports External Monitor Depending on the model you purchased: 15-pin, analog VGA port supports VESA DDC2B compatible functions. Universal Serial Bus The computer has Universal Serial Bus ports that (USB 2.0) comply with the USB 2.0 standard, which enables data transfer speeds 40 times faster than the USB 1.1 standard.
  • Page 41 Windows XP Home Edition, Windows ® Professional, or Windows XP Starter Edition operating system and TOSHIBA Utilities and drivers pre-installed on the hard disk. Refer to the Software section at the front of this chapter. TOSHIBA Utilities A number of utilities and drivers are pre-installed to make your computer more convenient to use.

  • Page 42: Special Features

    Introduction Special features The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use. Please note that the descriptions for starting some special features are based on setting the Control Panel to Category View. On Classic view the description is different.
  • Page 43 To specify the time, On Windows XP Home Edition/Professional model: Click Start, Control Panel, Performance and Maintenance. TOSHIBA Power Saver. On the Basic Setup tab, you can specify the time for HDD Power OFF. On Windows XP Starter Edition model: Click Start, Control Panel, Performance and Maintenance, Power Options.
  • Page 44 To specify the setting, On Windows XP Home Edition/Professional model: Click Start, Control Panel, Performance and Maintenance. TOSHIBA Power Saver. On the Setup Action tab, you can specify the setting for When I close the lid. On Windows XP Starter Edition model: Click Start, Control Panel, Performance and Maintenance, Power Options.
  • Page 45 Use the Fan item of the Basic Setup tab in TOSHIBA Power Saver. ■ Maximum Turns on fan first, then if...

  • Page 46: Utilities

    Please note that the descriptions for starting some Utilities are based on setting the Control Panel to Category View. On Classic view the description is different. TOSHIBA Assist TOSHIBA Assist is a graphical user interface that (Depends on the provides easy access to help and services. model you purchased.)
  • Page 47 TouchPad function. When you press these hot keys, the current setting will change and be displayed as an icon. TOSHIBA Touch and TOSHIBA Touch and Launch is a tool that allows Launch (Depends on you to perform various tasks easily using the the model you TouchPad.

  • Page 48: Options

    Use only DDRII-533MHz compatible memory modules. See your TOSHIBA dealer for details. Battery pack An additional battery pack can be purchased from your TOSHIBA dealer. Use it as a spare or replacement. AC Adaptor If you use your computer at more than one site...

  • Page 49: Chapter 2 The Grand Tour

    TOSHIBA Satellite L30/ Satellite Pro L30 Series Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Front with the display closed The following figure shows the computer's front with its display panel in the closed position.

  • Page 50: Left Side

    The Grand Tour Built-in HDD/ODD The Built-in HDD/ODD indicator glows green when the computer accesses the hard disk drive or and optical disc drive. Wireless The Wireless Communication Switch turns on the Communication wireless LAN. (Depends on the model you Switch purchased.) Set the switch to off in airplanes and hospitals.
  • Page 51 The Grand Tour External Monitor This 15-pin port lets you connect an external Port video display. The Analog VGA port supports VESA DDC2B compatible functions. (Depends on the model you purchased.) Cooling Vents Cooling vents help prevent the CPU from overheating.

  • Page 52: Right Side

    The Grand Tour Right side The following figure shows the computer's right side. Eject Button Emergency Indicator Eject Hole The right side of the computer ODD Indicator The ODD indicator glows amber when the computer accesses the optical disc drive. Eject Button Press this button to open the ODD tray.

  • Page 53: Underside

    The Grand Tour Universal Serial Bus A single of Universal Serial Bus port is on the (USB 2.0) ports back side. The port complies with the USB 2.0 standard, which enables data transfer speeds 40 times faster than the USB 1.1 standard (The ports also support USB 1.1).

  • Page 54: Front With The Display Open

    The Grand Tour Hard Disk Cover This cover protects the hard disk. Battery Release Slide this lock to prepare the battery pack for Lock (1) removal. Battery Pack The battery pack powers the computer when the AC adaptor is not connected. For detailed information on the battery pack, refer to Chapter 6, Power and Power-Up...

  • Page 55: Fixed Optical Media Drives

    The Grand Tour Power Button Turns the computer on and off as well as putting it into Hibernation mode and waking it up from Stand by mode. Display Screen The LCD displays high-contrast text and graphics. Refer to Appendix B, Display Controller Modes.

  • Page 56: Writable Discs

    The Grand Tour Writable discs This section describes the types of writable CD discs. Check the specifications of your drive for the type of discs it can write. Use TOSHIBA Disc Creator to write compact discs. Refer to Chapter 4, Operating Basics.

  • Page 57: Dvd-Rom & Cd-R/Rw Drive

    The Grand Tour DVD-ROM & CD-R/RW drive The full-size DVD-ROM & CD-R/RW drive module lets you record data to writable CDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor. The read speed is slower at the centre of a disc and faster at the outer edge.
  • Page 58 Use only the AC adaptor that came with the computer or an equivalent optional adaptor. Use of the wrong adaptor could damage your computer. TOSHIBA assumes no liability for any damage in such case. ■ Use only the AC Adaptor supplied with your computer or an equivalent adapter that is compatible.

  • Page 59: Getting Started

    TOSHIBA Satellite L30 / Satellite Pro L30 Series Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: ■ Setting up your work space - for your health and safety Be sure also to read the Safety Instruction Manual.

  • Page 60: Setting Up Your Work Space

    Getting Started Setting up your work space Establishing a comfortable work site is important for you and your computer. A poor work environment or stressful work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints.

  • Page 61: Placement Of The Computer

    Getting Started Placement of the computer Position the computer and peripheral devices to provide comfort and safety. ■ Set the computer on a flat surface at a comfortable height and distance. ■ The display should be no higher than eye level to avoid eyestrain. ■...

  • Page 62: Lighting

    Getting Started Lighting Proper lighting can improve legibility of the display and reduce eyestrain. ■ Position the computer so that sunlight or bright indoor lighting does not reflect off the screen. Use tinted Windows, shades or other screen to eliminate sun glare. ■...

  • Page 63: Installing The Battery Pack

    Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. ■ Do not touch the latch while holding the computer. Or you may get injured by the dropped battery by unintentional release of the latch.

  • Page 64: Connecting The Ac Adaptor

    Use only the AC adaptor supplied with your computer or an equivalent adaptor that is compatible. Use of any incompatible adaptor could damage your computer. TOSHIBA assumes no liability for any damage caused by use of an incompatible adaptor. ■...

  • Page 65: Opening The Display

    Getting Started 2. Connect the AC adaptor's DC output plug to the DC IN 19V jack on the back of the computer. Connecting the adaptor to the computer 3. Plug the power cord into a live wall outlet. Opening the display The display panel can be rotated in a wide range of angles for optimal viewing.

  • Page 66: Turning On The Power

    Getting Started Turning on the power This section describes how to turn on the power. After you turn on the power for the first time, do not turn it off until you have set up the operating system. Refer to the section Windows®...

  • Page 67: Turning Off The Power

    Getting Started Turning off the power The power can be turned off in one of the following modes: Shut down (Boot), Hibernation or Standby Mode. Shut Down mode (Boot mode) When you turn off the power in Shut Down mode no data is saved and the computer will boot to the operating system’s main screen.

  • Page 68: Starting Hibernation Mode

    For the computer to shut down in Hibernation Mode, the hibernation feature must be enabled in two places in Power Options: Hibernate tab and TOSHIBA Power Saver: Basic Setup tab. Otherwise, the computer will shut down in Standby Mode. If battery power becomes depleted, data saved in Standby Mode will be lost.

  • Page 69: Standby Mode

    ■ When the AC adaptor is connected, the computer will go into Standby Mode according to the settings in the TOSHIBA Power Saver. ■ To restore operation from Standby Mode, press the power button or press any key. The latter action works only if Wake-up on Keyboard is enabled in HW Setup.

  • Page 70: Restarting The Computer

    1. Click Start, click Turn Off Computer and click Stand by. 2. Close the display panel. This feature must be enabled. Refer to the Setup Action tab in TOSHIBA Power Saver Utility. 3. Press the power button. This feature must be enabled. Refer to the Setup Action tab in TOSHIBA Power Saver Utility.

  • Page 71: Create Optical Recovery Discs

    4. Insert the (first) blank media into the tray of the Optical Drive. 5. Click Start, All Programs, and Recovery Disc Creator. 6. After TOSHIBA Recovery Disc Creator starts, select the type of media and the title you wish to copy to the media then click the Create button.

  • Page 72: Restoring The Preinstalled Software From Recovery Media

    2. Hold down the F12 key and turn on the power. When In Touch with Tomorrow TOSHIBA appears, release the F12 key. 3. Use the upper or lower cursor key to select the CD/DVD in the display menu.

  • Page 73: Operating Basics

    TOSHIBA Satellite L30 / Satellite Pro L30 Series Chapter 4 Operating Basics This chapter gives information on basic operations including using the TouchPad, optical media drives, sound system, modem, the wireless LAN and LAN. It also provides tips on caring for your computer.

  • Page 74: Using The Optical Media Drive

    Operating Basics Do not press on the TouchPad too hard or press a sharp object such as a ball point pen against the TouchPad. The TouchPad could be damaged. For some functions, you can tap the TouchPad instead of pressing a control button.

  • Page 75: Loading Discs

    Operating Basics Loading discs To load a disc, follow the steps below and refer to the figures. 1. a. When the power is on, press the eject button to open the drawer slightly. Eject Button Pressing the eject button b. Pressing the eject button will not open the drawer when the disc drive's power is off.
  • Page 76 Operating Basics 2. Grasp the drawer gently and pull until it is fully opened. Pulling the drawer open 3. Place the disc, label side up, in the drawer. Inserting a disc User’s Manual...
  • Page 77 Operating Basics When the drawer is fully opened, the edge of the computer will extend slightly over the disc tray. Therefore, you will need to turn the disc at an angle when you place it in the tray. After seating the disc, however, make sure it lies flat, as shown in the figure above.

  • Page 78: Removing Discs

    Operating Basics Removing discs To remove the disc, follow the steps below and refer to the figure. Do not press the eject button while the computer is accessing the disc drive. Wait for the optical media drive indicator to go out before you open the drawer.

  • Page 79: Writing Cds With The Dvd-Rom & Cd-R/Rw Drive

    MITSUBISHI Chemical Corporation, Ricoh Co., Ltd. ■ Ultra-Speed CD-RW: MITSUBISHI Chemical Corporation TOSHIBA has confirmed the operation of CD-R and CD-RW media of the manufacturers above. Operation of other media cannot be guaranteed. ■ CD-RWs can generally be rewritten about 1,000 times. However, the actual number of rewrites is affected by the quality of the media and the way it is used.

  • Page 80: When Writing Or Rewriting

    Write from the computer's HDD to the CD. Do not try to write from shared devices such as a LAN server or any other network device. ■ Writing with software other than TOSHIBA Disc Creator has not been confirmed. Therefore, operation with other software cannot be guaranteed.

  • Page 81: Toshiba Direct Disc Writer

    ■ When writing the Setup files for the program into a disc formatted by TOSHIBA Direct Disc Writer and starting Setup from this disc, an error may occur. In this case, please copy them to your hard disk and then run Setup.

  • Page 82: Sound System

    Operating Basics 4. Hold the CD/DVD by its outside edge or the edge on the centre hole. Fingerprints on the surface can prevent the drive from properly reading data. 5. Do not expose to direct sunlight, extreme heat or cold. Do not place heavy objects on your CD/DVDs.

  • Page 83: Modem

    To select a region, follow the steps below. 1. Click start, point to All Programs, TOSHIBA, Networking, and click Modem Region Select. Do not use the Country/Region Select function in the Modem setup utility in the Control Panel if the function is available.

  • Page 84: Properties Menu

    Operating Basics Properties menu Click the icon with the secondary mouse button to display properties menu on the screen. Settings You can enable or disable the following settings: AutoRun Mode The Region Select utility starts automatically when you start up the operating system.

  • Page 85: Connecting

    Operating Basics Connecting To connect the modem cable, follow the steps below. ■ The modular cable that comes with the computer must be used to connect a modem. Connect the end of the modular cable with the core to the computer. ■...

  • Page 86: Disconnecting

    TOSHIBA strongly recommend the customer to enable the encryption function. ■ TOSHIBA is not liable for the eavesdropping of data due to the use of Wireless LAN and the damage thereof. Wireless communication switch You can enable or disable the Wireless LAN function, with the on/off switch.

  • Page 87: Wireless Communication Indicator

    Operating Basics Wireless communication indicator The wireless communication indicator indicates the status of the wireless communication functions. Indicator status Indication Indicator off Wireless communication switch is set to off. Automatic power down because of overheating. Power malfunction Indicator glows Wireless communication switch is on. Wireless LAN is turned on by an application.

  • Page 88: Connecting Lan Cable

    Operating Basics Connecting LAN cable To connect the LAN cable, follow the steps below. 1. Turn off the power to the computer and to all external devices connected to the computer. 2. Plug one end of the cable into the LAN jack. Press gently until you hear the latch click into place.

  • Page 89: Moving The Computer

    Operating Basics Moving the computer The computer is designed for rugged durability. However, a few simple precautions taken when moving the computer will help ensure trouble-free operation. ■ Make sure all disc activity has ended before moving the computer. Check the disc indicator on the computer. ■...
  • Page 90 Operating Basics 4-18 User’s Manual...

  • Page 91: Chapter 5 The Keyboard

    TOSHIBA Satellite L30 / Satellite Pro L30 Series Chapter 5 The Keyboard The computer's keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/ 102-key keyboard functions can be executed on the computer.

  • Page 92: F1 ... F12 Function Keys

    The Keyboard F1 ... F12 function keys The function keys (not to be confused with Fn) are the 12 keys at the top of your keyboard. These keys function differently from other keys. F1 through F12 are called function keys because they execute programmed functions when pressed.

  • Page 93: Hot Keys

    Power Save Mode is displayed in a dialog box. Continue holding down Fn and press F2 again to change the setting. You can also change this setting through the Profile item in TOSHIBA Power Saver. ® On Windows XP Starter Edition, pressing Fn +F2 opens Power Option Properties.
  • Page 94 The Keyboard Hibernation: When you press Fn + F4, the computer enters Hibernation Mode. To avoid entering Hibernation Mode unexpectedly, a dialog box appears for verification. However, if you select the check box, it will not appear in the future. Display selection: Press Fn + F5 to change the active display device.

  • Page 95: Fn Sticky Key (Depends On The Model You Purchased)

    Fn Sticky key (Depends on the model you purchased) You can use the TOSHIBA Accessibility Utility to make the Fn key sticky, that is, you can press it once, release it, and then press an " F number"...

  • Page 96: Windows ® Special Keys

    The Keyboard ® Windows special keys ® The keyboard provides two keys that have special functions in Windows ® Windows logo key activates the start menu and the other, the application key, has the same function as the secondary mouse button. ®...

  • Page 97: Temporarily Using Normal Keyboard (Overlay On)

    The Keyboard Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard without turning off the overlay: 1. Hold Fn and press any other key. All keys will operate as if the overlay were off.
  • Page 98 The Keyboard User’s Manual...

  • Page 99: Chapter 6 Power And Power-Up Modes

    TOSHIBA Satellite L30 / Satellite Pro L30 Series Chapter 6 Power and Power-Up Modes The computer's power resources include the AC adaptor and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes.

  • Page 100: Power Indicators

    Power and Power-Up Modes Power indicators As shown in the above table, the Battery. Power indicators on the system indicator alert you to the computer’s operating capability and battery charge status. Battery indicator Check the Battery indicator to determine the status of the battery pack. The following indicator lights indicate the battery status: Flashing orange The battery charge is low.

  • Page 101: Battery Types

    Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. ■ Do not remove the battery pack while the computer is in Standby Mode.

  • Page 102: Real Time Clock Battery

    The computer's RTC battery is a lithium ion battery and should be replaced only by your dealer or by a TOSHIBA service representative. The battery can explode if not properly replaced, used, handled or disposed of.

  • Page 103: Care And Use Of The Battery Pack

    Power and Power-Up Modes Care and use of the battery pack The battery pack is a vital component of portable computing. Taking proper care of it will help ensure longer operating time on battery power as well as a longer life for your battery pack. Follow the instructions in this section carefully to ensure safe operation and maximum performance.
  • Page 104 Never use the computer again until it has been checked by a TOSHIBA service provider. It might generate smoke or fire, or the battery pack might rupture. 3. Make sure the battery is securely installed in the computer before attempting to charge the battery pack.

  • Page 105: Charging The Batteries

    The computer enters Hibernate Mode only if Hibernation is enabled in two places: the Hibernate tab in Power Options and Setup Action tab in TOSHIBA Power Saver. You must recharge a battery pack when it becomes discharged. Procedures...

  • Page 106: Battery Charging Notice

    Power and Power-Up Modes Time The following table shows the approximate time required to fully charge a discharged battery. Charging time (hours) Battery type Power on Power off Battery pack (4000 mAh) About 12 or About 4 longer Battery pack (2000 mAh) About 12 or About 4 longer...

  • Page 107: Monitoring Battery Capacity

    Therefore, an often used, older battery will not operate for as long as a new battery even when both are fully charged. In this case, TOSHIBA Power Saver will indicate a 100% charge for both the old and new battery, but the displayed estimated time remaining will be shorter for the older battery.

  • Page 108: Retaining Data With Power Off

    Power and Power-Up Modes Retaining data with power off When you turn off your computer with fully charged batteries, the batteries retain data for the following approximate time periods. Battery pack (4000 mAh) About 3 days (Standby mode) About 30 days (Boot mode) Battery pack (2000 mAh) About 1 days (Standby mode) About 30 days (Boot mode)

  • Page 109: Replacing The Battery Pack

    Power and Power-Up Modes Replacing the battery pack When the battery pack reaches the end of its operating life you will need to install a new one. The life of the battery pack is generally about 500 recharges. If the Battery indicator flashes orange shortly after fully recharging the battery, the battery pack needs to be replaced.

  • Page 110: Installing The Battery Pack

    Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. ■ Do not touch the latch while holding the computer. Or you may get injured by the dropped battery by unintentional release of the latch.

  • Page 111: Power-Up Modes

    Power and Power-Up Modes Power-up modes The computer has the following power-up modes: ■ Boot Mode: Computer shuts down without saving data. Always save your work before you turn the computer off in boot mode. ■ Hibernation Mode: Data in memory is saved to the hard disk. ■...
  • Page 112 Power and Power-Up Modes 6-14 User’s Manual...

  • Page 113: Hw Setup (Depends On The Model You Purchased)

    Chapter 7 HW Setup (Depends on the model you purchased) This chapter explains how to use TOSHIBA HW Setup program to configure your computer. TOSHIBA HW Setup lets you configure settings for General, Password, Display, Boot Priority, Keyboard, LAN, and USB.

  • Page 114: User Password

    HW Setup (Depends on the model you purchased) Password This tab allows you to set or reset the user password for power on. User Password Lets you register a new password or un-register an existing password. Not Registered Un-registers an existing password Registered Register a new password by following the on screen instructions...
  • Page 115 HW Setup (Depends on the model you purchased) Keyboard Wake-up on Keyboard When this feature is enabled and the computer is in Standby mode, you can turn on the computer by pressing any key. It is effective only for the internal keyboard and only when the computer is in standby mode.
  • Page 116 HW Setup (Depends on the model you purchased) User’s Manual...

  • Page 117: Optional Devices

    TOSHIBA Satellite L30 / Satellite Pro L30 Series Chapter 8 Optional Devices Optional devices can expand the computer's capabilities and its versatility. This chapter describes connection or installation of the following devices, which are available from your TOSHIBA dealer: Cards/memory ■...

  • Page 118: Pc Card

    The computer is equipped with a PC Card expansion slot that can accommodate one Type II card. Any PC Card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slot supports 16-bit PC Cards, including PC Card 16’s multifunction card and CardBus PC Cards.

  • Page 119: Removing A Pc Card

    Optional Devices Removing a PC Card ■ Before removing a PC Card, make sure that any applications or system services do not use the card. ■ Be sure to disable the PC Card prior to removing it. Otherwise, the system may be fatally damaged. To remove the PC Card, follow the steps below.

  • Page 120: Memory Expansion

    RAM. This section describes how to install and remove a memory module. ■ Use only memory modules approved by TOSHIBA. ■ Do not try to install or remove a memory module under the following conditions. You can damage the computer and the module. Also, data will be lost.

  • Page 121: Installing A Memory Module

    Optional Devices Installing a memory module Follow the steps below to install a memory module. 1. Set the computer to boot mode and turn off the power. 2. Remove all cables connected to the computer. 3. Turn the computer upside down and remove the battery pack (refer to Chapter 6, Power and Power-Up Modes).

  • Page 122: Removing A Memory Module

    Optional Devices 7. Push the module down so it lies flat. Latches on either side will click into place to secure the module. Slot A Slot B Installing the memory module 8. Seat the cover and secure it with the screws. 9.

  • Page 123: Additional Battery Pack

    Optional Devices 5. Grasp the module by the sides and pull it out. ■ If you use the computer for a long time, the memory modules will become hot. In this case, let the memory modules cool to room temperature before you replace them. Or you will get burnt if you touch any of them.

  • Page 124: Additional Ac Adaptor

    Optional Devices Additional AC adaptor If you frequently transport the computer between different sites such as your home and office, purchasing an AC adaptor for each location will reduce the weight and bulk of your carrying load. External monitor An external analog monitor can be connected to the external monitor port on the computer.

  • Page 125: Security Lock

    Optional Devices Security lock Security locks enable you to anchor your computer to a desk or other heavy object to help prevent unauthorized removal of the computer. The computer has a security lock slot on the left side. Attach one end of the cable to a desk and the other end to the security lock slot.
  • Page 126 Optional Devices 8-10 User’s Manual...

  • Page 127: Troubleshooting

    TOSHIBA Satellite L30 / Satellite Pro L30 Series Chapter 9 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring.

  • Page 128: Preliminary Checklist

    Troubleshooting Preliminary checklist Consider the simplest solution first. The items in this checklist are easy to fix and yet can cause what appears to be a serious problem. ■ Make sure you turn on all peripheral devices before you turn on the computer.

  • Page 129: Hardware And System Checklist

    Troubleshooting Software The problems may be caused by your software or disc. If you cannot load a software package, the media may be damaged or the program might be corrupted. Try loading another copy of the software. If an error message appears while you are using a software package, check the software documentation.

  • Page 130: Self Test

    This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system, depending on how the Boot Priority is set in the TOSHIBA HW Setup program. If any of the following conditions are present, the self test failed: ■...

  • Page 131: Ac Power

    Troubleshooting AC power If you have trouble turning on the computer with the AC adaptor connected, check the Battery indicator. Refer to Chapter 6, Power and Power-Up Modes for more information. Problem Procedure AC adaptor doesn’t Check the connections. Make sure the cord is power the computer firmly connected to the computer and a power outlet.

  • Page 132: Real Time Clock

    Fully discharge the battery, then try to charge it again. Check the power consumption settings in the TOSHIBA Power Saver. Consider using a power saving feature. Real Time Clock Problem Procedure...

  • Page 133: Keyboard

    Troubleshooting Keyboard Keyboard problems can be caused by your setup configuration. For more information refer to Chapter 5, Keyboard. Problem Procedure Some letter keys Check that the numeric keypad overlay is not produce numbers selected. Press Fn + F11 and try typing again. Output to screen is Make sure the software you are using is not garbled...

  • Page 134: Cd-Rw & Dvd-Rom Drive

    Troubleshooting CD-RW & DVD-ROM drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access a Make sure the drive’s drawer is securely closed. CD/DVD in the drive Press gently until it clicks into place. Open the drawer and make sure the CD/DVD is properly seated.

  • Page 135: Pc Card

    Procedure Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: ■ Use only media recommended by TOSHIBA. ■ Do not use the mouse or keyboard during writing. ■ Use only the software supplied with the computer for recording.

  • Page 136: Pointing Device

    Troubleshooting Pointing device If you are using a USB mouse, also refer to the USB section in this chapter and to your mouse documentation. TouchPad Problem Procedure On-screen pointer does The system might be busy. If the pointer is not respond to Pad shaped as an hourglass, wait for it to return to its operation normal shape and try again to move it.

  • Page 137: Usb Mouse

    Troubleshooting Problem Procedure The response of the Adjust the touch sensitivity. TouchPad is too 1. Open the Control Panel. sensitive 2. Click the Printers and Other Hardware icon. 3. Click the Mouse icon. 4. Click the Device Setting tab. 5. Click the Setting button. 6.

  • Page 138: Usb

    Troubleshooting Problem Procedure The mouse pointer Try changing the speed setting in the mouse moves too fast or too control utility. slow 1. Open the Control Panel, select the Printers and Other Hardware icon, and press Enter. 2. Select the Mouse icon and press Enter. 3.

  • Page 139: Sound System

    Troubleshooting Sound system Refer also to documentation for your audio devices. Problem Procedure No sound is heard Check the software volume settings. Make sure the headphone connection is secure. If problems persist, contact your dealer. Monitor Refer also to Chapter 8, Optional Devices, and to your monitor’s documentation.

  • Page 140: Lan

    Troubleshooting Problem Procedure After making a call you Make sure the tone or pulse selection in your can’t hear a ring communications application is set correctly. You can also use the ATD command. Communication is cut The computer will automatically cut off off unexpectedly communication when connection with the carrier is not successful for a set time interval.

  • Page 141: Toshiba Support

    They are your best sources for current information and support. Where to write If you are still unable to solve the problem and suspect that it is hardware related, write to TOSHIBA at the nearest location listed on the below. Outside of Europe In Europe Australia Germany &...
  • Page 142 Troubleshooting Outside of Europe In Europe Singapore Spain TOSHIBA Singapore Pte. Ltd. TOSHIBA Information Systems, 438B Alexandra Road #06-01 ESPAÑA Alexandra Technopark Parque Empresarial San Fernando Singapore 119968 Edificio Europa, la Planta, Escalera A 28830 Madrid United States of America...

  • Page 143: Specifications

    TOSHIBA Satellite L30 / Satellite Pro L30 Series Appendix A Specifications This appendix summarizes the computer's technical specifications. Physical Dimensions Weight 2.3kg-2.7kg * Weight may vary depending on product configuration, vendor components, manufacturing variability and options selected. Size 358 (w) x 262 (d) x 37.0 (h) millimetres (not...
  • Page 144 Specifications Built-in Modem Network control unit (NCU) Type of NCU Type of line Telephone line (analog only) Type of dialling Pulse Tone Control command AT commands EIA-578 commands Monitor function Computer's speaker Communication specifications Communication Data: Full duplex System Fax: Half duplex Communication Data...
  • Page 145 Specifications Transmitting level -10 dBm Receiving level -10 to -40 dBm Input/output 600 ohms ±30% impedance Error correcting MNP class 4 and ITU-T V.42 Data compression MNP class 5 and ITU-T V.42bis Power supply +3.3V (supplied by computer) User’s Manual...
  • Page 146 Specifications User’s Manual...

  • Page 147: Display Controller And Modes

    TOSHIBA Satellite L30 / Satellite Pro L30 Series Appendix B Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular picture elements (pels) on or off. The controller is an advanced Video Graphics Array (VGA) that provides Graphics Array (XGA) support for the internal LCD and external monitors.

  • Page 148: Video Modes

    Display Controller and Modes Video modes The computer supports video modes defined in the tables below. If your application offers a selection of mode numbers that do not match the numbers on the table, select a mode based on mode type, resolution, character matrix, number of colors and refresh rates.
  • Page 149 Display Controller and Modes Table 1: Video modes (VGA) (continued) Video Type Resolution Character Scanning mode matrix colors colors frequency (pels) Vertical (Hz) 320 x 200 8 x 8 16 of 256K 16 of 256K Grph Pels 640 x 200 8 x 8 16 of 256K 16 of 256K...
  • Page 150 Display Controller and Modes Table 2: Video modes Resolution LCD colors CRT colors Vertical frequency (Hz) 800 x 600 256K/256K 256K/256K 1024 x 768 256K/256K 256K/256K 1280 x 800 256K/256K 256K/256K 1280 x 1024 256K/256K 256K/256K (Virtual) 1600 x 1200 256K/256K 256K/256K (Virtual)
  • Page 151 Display Controller and Modes Table 2: Video modes (continued) Resolution LCD colors CRT colors Vertical frequency (Hz) 800 x 600 64K/64K 64K/64K 1024 x 768 64K/64K 64K/64K 1280 x 800 64K/64K 64K/64K 1280 x 1024 64K/64K 64K/64K (Virtual) 1600 x 1200 64K/64K 64K/64K (Virtual)
  • Page 152 Display Controller and Modes Table 2: Video modes (continued) Resolution LCD colors CRT colors Vertical frequency (Hz) 800 x 600 16M/16M 16M/16M 1024 x 768 16M/16M 16M/16M 1280 x 800 16M/16M 16M/16M 1280 x 1024 16M/16M 16M/16M (Virtual) 1600 x 1200 16M/16M 16M/16M (Virtual)

  • Page 153: Display Settings

    Display Controller and Modes Display Settings 1. You cannot move from the Settings tab of Display Properties to the multi-monitor when you are using the display of the computer and an external CRT display at the same time. ■ The Settings tab is displayed in the following steps; ■...
  • Page 154 Display Controller and Modes ■ The way to move to multi-monitor (ATI RADEON XPRESS 200M) ■ Switch to Display Properties, like shown in previous page. ■ Click Advanced in Display Properties. ■ Select Displays tab in (Multiple Monitors) and ATI RADEON XPRESS 200M Series Properties.
  • Page 155 Display Controller and Modes 5. When the LCD (internal liquid crystal display) display mode is selected, the Virtual (Virtual Screen) display mode can be set. However, afterwards, it may not possible to change the screen resolution to more than 1280 x 1024 pixels in Highest (32bit) mode (for example, when you attempt to set the resolution to 1600 x 1200 using the Screen resolution slide bar and then select Highest (32bit) mode from the Color quality drop-down menu).
  • Page 156 Display Controller and Modes B-10 User’s Manual...

  • Page 157: Card Specifications

    TOSHIBA Satellite L30 / Satellite Pro L30 Series Appendix C Wireless LAN Card Specifications Form Factor Mini PCI TypeIII ■ IEEE 802.11 Standard for Wireless LANs Compatibility ■ Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. The "Wi-Fi CERTIFIED" logo is a certification mark of the Wi-Fi Alliance.

  • Page 158: Radio Characteristics

    Wireless LAN Radio Characteristics Radio Characteristics of Wireless LAN Cards may vary according to: ■ Country/region where the product was purchased ■ Type of product Wireless communication is often subject to local radio regulations. Although Wireless LAN wireless networking products have been designed for operation in the license-free 2.4GHz band, local radio regulations may impose a number of limitations to the use of wireless communication equipment.
  • Page 159 Subject to the radio regulations that apply in the countries/regions, your Wireless LAN card may support a different set of 2.4 GHz channels. Consult your Authorized Wireless LAN or TOSHIBA Sales office for information about the radio regulations that apply in the countries/regions.
  • Page 160 Wireless LAN When installing Wireless LAN cards, the channel configuration is managed as follows: ■ For wireless clients that operate in a Wireless LAN Infrastructure, the Wireless LAN card will automatically start operation at the channel identified by the Wireless LAN Access Point. When roaming between different access points the station can dynamically switch to another channel if required.

  • Page 161: Ac Power Cord And Connectors

    TOSHIBA Satellite L30 / Satellite Pro L30 Series Appendix D AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following...
  • Page 162 AC Power Cord and Connectors In Europe, power cords must be VDE type, H05VVH2-F and two conductor. For the United States and Canada, plug configuration must be a 2-15P (250 V) or 1-15P (125 V) as designated in the U.S. National Electrical code handbook and the Canadian Electrical Code Part II.
  • Page 163 TOSHIBA Satellite L30 / Satellite Pro L30 Series Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference. Abbreviations AC: alternating current AGP: accelerated graphics port ANSI: American National Standards Institute APM: advanced power manager...
  • Page 164 Glossary LED: light emitting diode LSI: large scale integration ® MS-DOS: Microsoft disk Operating System OCR: optical character recognition (reader) PCB: printed circuit board PCI: peripheral component interconnect RAM: random access memory RGB: red, green, and blue ROM: read only memory RTC: real time clock SCSI: small computer system interface SIO: serial input/output...
  • Page 165 Glossary application: A group of programs that together are used for a specific task such as accounting, financial planning, spread sheets, word processing and games. ASCII: American Standard Code for Information Interchange. ASCII code is a set of 256 binary codes that represent the most commonly used letters, numbers, and symbols.
  • Page 166 Glossary cache memory: High speed memory which stores data that increases processor speed and data transfer rate. When the CPU reads data from main memory, it stores a copy of this data in cache memory. The next time the CPU needs that same data, it looks for it in the cache memory rather than the main memory, which saves time.
  • Page 167 Glossary computer program: A set of instructions written for a computer that enable it to achieve a desired result. computer system: A combination of hardware, software, firmware, and peripheral components assembled to process data into useful information. configuration: The specific components in your system (such as the terminal, printer, and disk drives) and the settings that define how your system works.
  • Page 168 A collection of related information; a file can contain data, programs, or both. firmware: A set of instructions built into the hardware which controls and directs a microprocessor’s activities. Fn-esse: A TOSHIBA utility that lets you assign functions to hot keys. Glossary-6 User’s Manual...
  • Page 169 Fn, can be used to set system parameters, such as speaker volume. HW Setup: A TOSHIBA utility that lets you set the parameters for various hardware components. icon: A small graphic image displayed on the screen or in the indicator ®...
  • Page 170 Glossary interface: 1) Hardware and/or software components of a system used specifically to connect one system or device to another. 2) To physically connect one system or device to another to exchange information. 3) The point of contact between user, the computer, and the program, for example, the keyboard or a menu.
  • Page 171 Glossary main board: See motherboard. megabyte (MB): A unit of data storage equal to 1024 kilobytes. See also kilobyte. megahertz: A unit of wave frequency that equals 1 million cycles per second. See also hertz. menu: A software interface that displays a list of options on the screen. Also called a screen.
  • Page 172 A Class A device is sufficient for office use. Class B provides a more stringent classification for home equipment use. TOSHIBA portable computers comply with Class B computing device regulations. Random Access Memory (RAM): High speed memory within the computer circuitry that can be read or written to.
  • Page 173 TFT display: A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology with thin film transistor (TFT) to drive each cell. TouchPad: A pointing device integrated into the TOSHIBA computer palm rest. User’s Manual...
  • Page 174 Glossary TTL: Transistor-transistor logic. A logic circuit design that uses switching transistors for gates and storage. Universal Serial Bus: This serial interface lets you communicate with several devices connected in a chain to a single port on the computer. VGA: Video Graphics Array is an industry standard video adaptor that lets you run any popular software.
  • Page 175 TOSHIBA Satellite L30 / Satellite Pro L30 Series Index AC adaptor, 1-3 Display, 1-5 additional, 1-14 automatic power off, 1-8 connecting, 3-6 brightness decreases, 5-4 ASCII characters, 5-7 brightness increases, 5-4 controller, 1-5 opening, 3-7 Battery Display controller, B-1 charging, 6-7...
  • Page 176 Index creases), 5-4 Memory, 1-3 Fn + F7 (Display Brightness in- expansion, 1-14, 8-4 creases), 5-4 installing, 8-5 Fn + F8 (Wireless setting), 5-4 removing, 8-6 Fn + F9 (Touch Pad), 5-4 Modem, 1-6, 4-11 Fn Sticky key, 5-5 connecting, 4-13 Function keys, 5-2 disconnecting, 4-14 properties menu, 4-12...
  • Page 177 Index Hardware and system checklist, 9-3 TOSHIBA ConfigFree, 1-13 Keyboard, 9-7 TOSHIBA Direct Disc Writer, LAN, 9-14 1-13 LCD panel, 9-7 TOSHIBA Disc Creator, 1-12 Memory expansion, 9-12 TOSHIBA PC DiagnosticTool, Modem, 9-13 1-13 Monitor, 9-13 TOSHIBA Utilities, 1-7 overheating power down,...
  • Page 178 Index Index-4 User’s Manual...

This manual is also suitable for:

Satellite l30 seriesSatellite pro l30 series

Table of Contents