Programming The Quantity Of Coffee And Milk In The Cup For Cappuccino Or Milk; Hot Water; Changing The Quantity Of Water Delivered Automatically; Cleaning - DeLonghi ECAM22.36X Instructions For Use Manual

Programming the quantity of coffee and milk in
the cup for cappuccino or milk
The appliance is set by default to automatically deliver standard
quantities. To change these quantities, proceed as follows:
1. Place a cup under the coffee spouts and milk spout.
2. Press and hold the CAPPUCCINO button until the message
"PROGRAM MILK Program quantity" is displayed.
3. Release the button. The appliance starts delivering milk.
4. Once the required quantity of milk has been delivered into
the cup, press the CAPPUCCINO button again.
5. The appliance stops delivering milk and after a few secon-
ds the coffee is delivered into the cup. "PROGRAM COFFEE
Program quantity" is displayed.
6. Once the required quantity of coffee has been delivered
into the cup, press the CAPPUCCINO button. Coffee delivery
stops.
The machine is now reprogrammed with the new milk and cof-
fee quantities.

HOT WATER

Important! Danger of burns.
Never leave the machine unsupervised while hot water is being
delivered. The spout becomes hot during delivery. Hold by the
handle only.
1. Make sure the hot water spout is attached correctly (fig. 4).
2. Place a container under the spout (as close as possible to
avoid splashes).
3. Press the button (fig. 21). "HOT WATER" is displayed,
together with a progress bar which fills gradually as prepa-
ration proceeds.
4. The machine delivers 250 ml of hot water, then delivery
stops automatically. To interrupt delivery of hot water ma-
nually, press the
Please note!
If "Energy saving" mode is active, you may have to wait a few
seconds before the hot water is delivered.
Changing the quantity of water delivered
automatically
The machine is set by default to automatically deliver 250 ml of
hot water. To modify these quantities, proceed as follows:
1. Position a container under the spouts.
2. Press and hold the
quantity" is displayed, then release.
3. When the hot water in the cup reaches the required level,
press the button again.
The machine is now reprogrammed with the new quantity.
button again.
button until "HOT WATER Program

CLEANING

Important!
• Do not use solvents, abrasive detergents or alcohol to clean
the appliance. With De'Longhi superautomatic coffee ma-
chines, you need not use chemical products to clean the
machine.
• Do not use metal objects to remove encrustations or coffee
deposits as they could scratch metal or plastic surfaces.
Cleaning the coffee grounds container
When "EMPTY GROUNDS CONTAINER" is displayed, the grounds
container must be emptied and cleaned.
Until the grounds container has been cleaned, the appliance
continues to display the message and coffee cannot be made.
To clean (with the machine on):
• Remove the drip tray (fig. 22), empty and clean.
• Empty the grounds container and clean thoroughly to re-
move all residues left on the bottom.
• Check the red condensate tray and empty if necessary.
Important!
When removing the drip tray, the grounds container must be
emptied, even if it contains few grounds.
If this is not done, when you make the next coffees, the grounds
container may fill up more than expected and clog the machine.

Cleaning the drip tray and condensate tray

Important!
If the drip tray is not emptied regularly, the water could over-
flow from the edge and seep inside or around the coffee maker.
This could damage the machine, the surface it rests on or the
surrounding area.
The drip tray is fitted with a level indicator (red) showing the
level of water it contains (fig. 23).
Before the indicator protrudes from the cup tray, the drip tray
must be emptied and cleaned.
To remove the drip tray:
1. Remove the drip tray and the grounds container (fig. 24);
2. Empty the drip tray and grounds container and wash them;
3. Check the condensate tray and empty if necessary.
4. Replace the drip tray and grounds container.
14