1. Manuals
  2. Brands
  3. Vega Manuals
  4. Transmitter
  5. RMT-10
  6. Instruction manual

Vega RMT-10 Instruction Manual

Vhf rack-mount transmitter
Hide thumbs
Table of Contents

Advertisement

Quick Links

RMT-10 VHF
Rack-Mount Transmitter
Instruction Manual
099-0068D

Advertisement

Table of Contents
loading

Related Manuals for Vega RMT-10

Summary of Contents for Vega RMT-10

  • Page 1 RMT-10 VHF Rack-Mount Transmitter Instruction Manual 099-0068D...

  • Page 2: Table Of Contents

    Quick Start ......2 A Word to Vega Users ....2 Unpacking .
  • Page 3 9. Set the rear-panel INPUT LEVEL (MIC/LINE switch) to the LINE position. 10. Set the rear-panel AUDIO COMPRESSION switch to LINEAR. 11. Turn on the RMT-10 with the front-panel POWER switch. 12. With an audio input applied to the unit, adjust the front-panel INPUT LEVEL ADJUST control until the AUDIO LEVEL bargraph meter indicates peaks in the 0 to +2 VU range.

  • Page 4: Introduction

    216 MHz. Consult your dealer or the Vega factory for details. The RMT-10 accepts either line or mic audio via a standard XLR connector. The “input level” switch allows selection between mic (–40 to –10 dBu) or line (–10 and +20 dBu) audio input.

  • Page 5: Installation

    For stand-alone operation: Peel off the four rubber feet's protective paper (provided with the RMT-10) and attach to the bottom of the chassis at each corner. For rack-mount use, the detachable rack-mount “ears” must first be installed on the RMT-10 as follows: 1.

  • Page 6: Whip Antenna Length

    Power Supply WARNING: If providing dc power from another source, external fusing is strongly advised. No internal circuit fuse is provided with the RMT-10. The provided power supply is internally impedance- and thermal-limited and therefore does not require additional circuit protection. Consult the Vega factory for more information.

  • Page 7: Adjustments

    Audio Level Setting The RMT-10 accommodates audio levels between –40 dB to +20 dB, a 60 dB range. If you know the approximate level of the input audio, set the mic/line as follows:...

  • Page 8: Frequency-Compensation Adjustments

    For successful operation, it is necessary to choose a transmit frequency for the RMT- 10 that can coexist with other RF systems in the coverage area. The frequency of the RMT-10 must be specified at the time of purchase. The Vega factory provides a frequency-coordination service free of charge for this purpose.

  • Page 9: Antennas

    Transmitter Antennas Proper mounting and placement of antenna(s) is vitally important in wireless systems. If overlooked, antennas might cause unnecessary problems. In all cases, a clear and unobstructed line-of-sight path between the transmitting antenna and the receiver(s) is required. The antenna might be concealed behind fabric, thin plastic, acoustic tile, and thin plywood without significantly affecting performance.

  • Page 10: Vega Rmt-

    (at our option) without charge during the one-year period, if delivered to the Vega factory. Warranty does not extend to damage due to improper repairs, finish or appearance items, malfunction due to abuse or operation under other than the specified conditions, nor to incidental or consequential damages.

  • Page 11: Specifications

    H × 5.1 in (13 cm) D, excluding detachable rack- mount ears Weight: 3.2 lb (1.5 kg), without power supply www.vega wireless ..c om 9900 East Baldwin Place • El Monte, California 91731-2294 Telephone: (626) 442-0782 • Toll-Free: 800-877-1771 Fax: (626) 444-1342 •...

Table of Contents