Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Paslode Paslode 403606-10
Summary of Contents for Paslode Paslode 403606-10
- Page 1 PNEUMATIC TOOLS Operating and Maintenance Manual 403606-10 08/02...
- Page 2 PASLODE MODEL NUMBER DESIGNATION The model number of each Paslode tool contains information about the tool and the fasteners that are used with it. The following example illustrates the information contained in this tool model number. NAILER Tool application letter Maximum fastener length, in inches that can be used with the...
-
Page 3: Table Of Contents
INTRODUCTION Congratulations on purchasing a Paslode pnuematic tool. You have made a wise choice. A Paslode tool is a professional quality tool that combines power and speed in a light weight design for versatile operation in a variety of industial and construction applications. Please take the time to review this entire manual and all other documentation that came with the tool. -
Page 4: Safety Instructions
SAFETY INSTRUCTIONS SAFETY FIRST These safety instructions provide information necessary for safe operation of Paslode ® tools. DO NOT ATTEMPT TO OPERATE THE TOOL UNTIL YOU READ AND UNDERSTAND ALL SAFETY PRECAUTIONS AND MANUAL INSTRUCTIONS. WEAR EYE AND HEARING PROTECTION Always wear hearing and eye protection devices, in- cluding side shields, when operating or working in the vicinity of a tool. -
Page 5: Air Systems
AIR SYSTEMS For air-powered tools to work their best, the air supply system must be properly installed and maintained regularly. A drawing in this section shows a properly installed air supply system. Handy checklists for installing and maintaining air supply systems follow. Indoor Air System Installation -Be certain that: •... - Page 6 19 scfm of air is required. Because in compressors approximately 1 hp is required to produce 4 scfm, a compressor of at least 5 hp is required. Calculated Required Piping For example, given a 20 hp electric compressor...
-
Page 7: Tool Installation
TOOL INSTALLATION Your Paslode tool comes ready for immediate use and can be installed by following these steps: 1. SAFETY - All tool operators and their immediate supervisors must become familiar with the operator safety instructions before operating the tool. The instructions are on page 2 of this manual. -
Page 8: Tool Loading
TOOL OPERATION - continued MOVE UP TO INCREASE DRIVE DEPTH MOVE DOWN TO DECREASE DRIVE DEPTH SOCKET HEAD CAPSCREW Precision Placement Driving Grasp the tool handle firmly and hold the bottom of the work contacting element firmly against the workpiece until it is com- pletely depressed. - Page 9 Coil Nailers Step No. 1 – Grasp the nailer handle firmly with one hand and with the other hand unlatch the magazine cover clip. Swing the magazine door open. Step No. 2 – Adjust the loading tray for nail length (if required) by depressing the button on the post and raising or lowering the tray to the desired position.
- Page 10 PowerMaster Plus Series Strip Nailer Step No. 1 – Grasp the nailer handle firmly. Pull the magazine follower all the way to the rear of the magazine until it is latched into its loading position by the magazine latch. Step No. 2 – Insert the a strip of fasteners into the top of the magazine with the point of the nails facing the nose area.
- Page 11 2000 Series Stapler Step No. 1 – Grasp the stapler firmly with one hand. Depending on the model,either squeeze the latch with your small finger or press it with your thumb With your other hand, pull the magazine back towards you. Step No.
-
Page 12: Maintenance
MAINTENANCE ® Paslode tools are built for ease of maintenance. A few simple details will assure trouble-free operation and long tool life. Anyone who uses or maintains the tool must read the safety and maintenance instructions. Study the sche- matic drawing before starting any repairs on the tool. Air-operated tools must be inspected periodically, and worn or broken parts must be replaced to keep the tool operating safely and efficiently. - Page 13 MAINTENANCE - Continued ACTION Drain air line filter(daily). Keep lubricator filled. Clean filter element-then blow air through filter in direction opposite to normal flow. Check that all screws on tool are tight. Keep work contacting elelment working properly. Keep magazine and feeder mechanism clean.
-
Page 14: Operator Troubleshooting
OPERATOR TROUBLESHOOTING PROBLEM Fasteners will not drive completely into wood. Fasteners penetrate properly during normal operation, but won't drive fully at faster speeds. Fasteners drive too deeply into wood. Fastener jams in nose of tool. Tools skips during operation - no fasteners are driven from time to time. -
Page 15: Tool Warranty
TOOL WARRANTY An Illinois Tool Works Company 888 Forest Edge Drive Vernon Hills, Illinois 60061 TOOL WARRANTY AND LIMITATIONS...