Paslode 900420 Operating Manual
  1. Manuals
  2. Brands
  3. Paslode Manuals
  4. Nail Gun
  5. 900420
  6. Operating manual

Paslode 900420 Operating Manual

Cordless framing nailer
Hide thumbs

Advertisement

Table of Contents

Printed in U.S.A.
© 2010 Illinois Tool Works, Inc.
405658-5
03/10
Part No. 900420
CORDLESS
FRAMING NAILER
IMPORTANT
DO NOT DESTROY
It is the customer's responsibility to
have all operators and service personnel
read and understand this manual.
OPERATING MANUAL
21

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 900420 and is the answer not in the manual?

Questions and answers

Related Manuals for Paslode 900420

Summary of Contents for Paslode 900420

  • Page 1 Part No. 900420 CORDLESS FRAMING NAILER IMPORTANT DO NOT DESTROY It is the customer's responsibility to have all operators and service personnel read and understand this manual. Printed in U.S.A. OPERATING MANUAL © 2010 Illinois Tool Works, Inc. 405658-5 03/10...

  • Page 2: Introduction And Warranty

    Service Center listing that was provided with your tool. ONE-YEAR LIMITED WARRANTY Paslode's sole liability hereunder will be to replace any part or accessory which proves to be defective within the specific time period. Any replacement A one-year warranty will apply to all parts, except those listed...

  • Page 3: Table Of Contents

    Contents Introduction and Warranty ............2 An Overview of the Paslode Cordless Framing Nailer ....4 Safety Instructions..............5 Battery and Charging System ........... 8 Fuel Cell and Metering Valve ..........10 Preparing the Paslode Cordless Framing Nailer for Use ..13 Paslode Cordless Framing Nailer Operation ......14 Fasteners and Applications .............

  • Page 4: An Overview Of The Paslode Cordless Framing Nailer

    As you examine the Cordless Framing Nailer, become By using the Paslode Cordless Framing Nailer at its familiar with the two major assemblies and the various recommended cycle rate, you will be able to drive several components located in each of them.

  • Page 5: Safety Instructions

    The following safety instructions have been included in this WARNING booklet to provide you with basic information necessary for safe operation of the Paslode Cordless Framing Nailer. DO NOT ATTEMPT TO OPERATE THIS TOOL UNTIL YOU HAVE READ AND UNDERSTAND ALL SAFETY Never expose or store the PRECAUTIONS AND MANUAL INSTRUCTIONS.
  • Page 6 NEVER operate the tool if the work contacting element vicinity of the Paslode is not working properly. Cordless Framing Nailer. 8. ALWAYS POINT THE TOOL AWAY FROM YOURSELF AND OTHERS WHEN CLEARING JAMS OR REMOVING FASTENERS.
  • Page 7 Battery Disposal: The Paslode Cordless batteries contain cadium and must be recycled or disposed of properly. It is illegal in some areas to place a nickel-cadium battery into the trash or solid waste stream. You may contact your local recycling center for information on where to return the spent battery or call 1-800-822-8837 for information on Ni-Cd battery recycling in your area.

  • Page 8: Battery And Charging System

    This charging system 1. Remove wall mount unit with the orange label from is the only one that will work with all Paslode batteries the tool case and plug into a 120V AC outlet. Set (round or oval).
  • Page 9 Battery and Charging System Battery Indicator Light The illustration is a close-up of the side of the Paslode Cordless framer handle. On the side of the handle is a small plastic lens. This is the battery indicator light. When you insert a fully-charged battery into the tool, you will see a blinking green light.

  • Page 10: Fuel Cell And Metering Valve

    NOTE: Altitude Restriction Never inhale the spray. Paslode Cordless tools are powered by an internal combustion engine and are effected by altitude. The Keep out of the reach of children. tool may lose power or not cycle consistantly at elevations of 4000 feet or greater.
  • Page 11 Paslode Cordless Fuel Cell Disposal Guidelines Paslode the industry leader in cordless technology provides this information to assist users with the proper disposal of discarded fuel cells. Acceptable disposal options vary depending on the type of fuel cell users. All users must consider federal, state and local solid waste regulations to ensure that discarded fuel cells are disposed of properly.
  • Page 12 Fuel Cell and Metering Valve Inserting Fuel Cell As you slide the metering valve/fuel cell assembly into the Cordless Framing Nailer, you will notice a red adapter at the Inserting the metering valve/fuel cell assembly into the top of the cylinder pocket. As shown in the illustration, this Cordless Framing Nailer is very simple.

  • Page 13: Preparing The Paslode Cordless Framing Nailer For Use

    The use of nails that do not meet Paslode tool components. Five (5) nails will be left in the standards could cause tool damage and void your warranty.

  • Page 14: Paslode Cordless Framing Nailer Operation

    Paslode Cordless Framing Nailer Operation PRESS WORK – CONTACTING ELEMENT AGAINST THE WORK SURFACE. Move up to Increase Drive Depth Fan motor starts, Move Down to Reduce fuel is injected into Drive Depth combustion chamber and mixed with air by the fan.

  • Page 15: Fasteners And Applications

    Hardened Steel - For attaching wooden plates to green corosion resistance of any galvanized nail. concrete foundations; 2X furring strips to cinder block. The Paslode Cordless Framing Nailer is not recommended for use with 3" Ring Shank nails in pressure treated lumber...

  • Page 16: Servicing

    Framing Nailer, clearing a jammed fastener is easy: 1. Remove the fuel cell and battery. Never attempt any maintenance of the Paslode Cordless 2. Lock follower back in magazine and remove fasteners. Framing Nailer without first removing the fuel cell and 3.
  • Page 17 Soap and water restores the Paslode Cordless Faming Nailer filter to a "like new" condition. Tool Accessories A variety of accessories are available for the Paslode Grille Cordless Framing Nailer: No-Mar Work Contacting Element - Part No. 901252 Battery - Part No.

  • Page 18: Troubleshooting

    Check lockout. If unable to free return tool to Lockout bracket is stuck in lockout position. fully - tool does not operate. authorized Paslode dealer for service. Remove and inspect lower probe. Clean and Work-contacting element is bent, or build-up of lubricate track with Cordless Lubricating oil.
  • Page 19 If tool will not operate after following the above service directions, return the tool to an authorized Paslode.® representative for service. For the nearest Paslode® representative call 1-800-682-3428. For factory direct service call 1-800-447-3830. For Tec hnical support call 1-800-222-6990 or visit our web site at www.paslode.com. To purchase parts, visit our website at www.itwconstructionparts.com...

  • Page 20: Forest Edge Drive Vernon Hills, Illinois

    An Illinois Tool Works Company 888 Forest Edge Drive Vernon Hills, Illinois 60061 www.paslode.com...

This manual is also suitable for:

Cordless framing nailer

Table of Contents

Save PDF