Table of Contents
Advertisement
OWNER'S
MANUAL
Part Number P474-2300RF
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
Transmitter Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Transmitter Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Transmitter Front Panel Buttons . . . . . . . . . . . . . . . . . . . . . . . 4
Set Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Programming Thermostat Schedules . . . . . . . . . . . . . . . . . . . . 7
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Auto-Changeover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Electric Heat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Dry Contact Switch/External Device . . . . . . . . . . . . . . . . . . . . . 13
Two-Stage Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Fan Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
IMPORTANT: Read entire instructions before programming the
thermostat.
Manufacturer reserves the right to
discontinue, or change at any time,
specifications or designs without notice
and without incurring obligations.
CPE230RF
Programmable Thermostat
CONTENTS
REPLACEMENT COMPONENTS DIVISION
CARRIER CORPORATION 10/98
LITERATURE NUMBER P474-6SO
PRINTED IN CHINA
Commercial
Wireless Transmitter
Page
Advertisement
Table of Contents
Related Manuals for TOTALINE CPE230RF
Summary of Contents for TOTALINE CPE230RF
-
Page 1: Table Of Contents
OWNER’S CPE230RF Commercial MANUAL Programmable Thermostat Wireless Transmitter Part Number P474-2300RF CONTENTS Page GENERAL ......... . 2 CONFIGURATION . -
Page 2: General
GENERAL The 7-day, commercial, programmable thermostats maintain room tem- perature by controlling the operation of your heating, cooling, and ventilation system. Separate heating and cooling set points and auto-changeover capa- bility allow you to program schedules for energy savings. All thermostats allow up to 4 time/temperature settings to be programmed per 24-hr period. -
Page 3: Configuration
CONFIGURATION Transmitter Display — The transmitter display is located in the center of the transmitter. See Fig. 1. The following information can be displayed on the screen: • mode (OFF, HEAT, COOL, AUTO, or PROGRAM ON) • fan setting (FAN ON or blank) •... -
Page 4: Transmitter Display
Fig. 1 — Transmitter Display Transmitter Front Panel Buttons — The transmitter has buttons which are used to raise or lower the desired set point and change the mode. See Fig. 2. SET POINT BUTTONS — The UP ARROW and DOWN ARROW buttons will raise or lower the current desired temperature set point. -
Page 5: Transmitter Indicator
MODE BUTTON — The Mode button selects the operating mode of the thermostat. • If OFF is selected, the thermostat will not enter Heating or Cooling mode. • If HEAT is selected, the thermostat will only enter Heating mode (if the room temperature is below the heating set point). - Page 6 KEYPAD LOCK — The thermostat has a keypad lockout feature which will not allow anyone to change the settings of your thermostat unless the correct button sequence is pressed. To disable or lock the keypad, press and hold the Mode button. While holding down the Mode button, press the UP and DOWN ARROW buttons simultaneously.
-
Page 7: Set Clock
Set Clock — The Mode and Override buttons allow you to change the time and day displayed on the thermostat. To set the clock, press and hold the Mode and Override buttons for 2 sec- onds. See Fig. 3. The display will show the Setup annunciator. The current time will blink on and off. - Page 8 Occupied 2, Occupied 3, Unoccupied) time periods. Each occupied time pe- riod has a start time, stop time, heating set point, and cooling set point. The unoccupied time period has a heating set point and a cooling set point. The unoccupied time period is active whenever an occupied time period is not active.
- Page 9 3. The heating set point for Occupied 1 will be displayed. Use the UP AR- ROW and DOWN ARROW buttons to raise or lower the heating set point until the desired temperature is shown. The range of acceptable values is 35 to 99 F (1 to 37 C). Press the Mode button to continue. See Fig. 4. 4.
- Page 10 11. The Copy command can be used to copy the previous day’s schedule if the schedules are the same. The copy command becomes available after all the occupied periods are programmed in a day. Use the UP ARROW to change the copy command to YES. Use the DOWN ARROW to change the copy command to NO.
- Page 11 Fig. 5 — Start Time Display Fig. 6 — Copy Command Display...
- Page 12 Table 1 — Daily Schedule Planner SCHEDULE OF THE Occupied 1 Occupied 2 Occupied 3 Unoccupied WEEK Start / Stop / Heat / Cool Start / Stop / Heat / Cool Start / Stop / Heat / Cool Heat / Cool Monday Tuesday Wednesday...
-
Page 13: Operation
OPERATION The Mode button selects the operating mode of the thermostat. If OFF is selected, the thermostat will not enter Heating or Cooling mode. If HEAT is selected, the thermostat will only enter Heating mode (if the room tempera- ture is below the heating set point). If COOL is selected, the thermostat will only enter Cooling mode (if the room temperature is above the cooling set point). - Page 16 Your Assurance of Quality ALL Totaline products are backed with a one-year warranty by Carrier Corporation, the world’s largest manufacturer of air conditioning, heating, and refrigeration products. Manufacturer reserves the right to REPLACEMENT COMPONENTS DIVISION discontinue, or change at any time, CARRIER CORPORATION 10/98 specifications or designs without notice LITERATURE NUMBER P474-6SO...
Need help?
Do you have a question about the CPE230RF and is the answer not in the manual?
Questions and answers