HP Compaq Mini 700 Maintenance And Service Manual
  1. Manuals
  2. Brands
  3. HP Manuals
  4. Laptop
  5. Compaq Mini 700
  6. Maintenance and service manual

HP Compaq Mini 700 Maintenance And Service Manual

Hewlett-packard netbook maintenance and service guide
Hide thumbs
Table of Contents

Advertisement

Quick Links

HP Mini 1000 Netbook
Compaq Mini 700 Netbook
Maintenance and Service Guide

Advertisement

Table of Contents
loading

Related Manuals for HP Compaq Mini 700

Summary of Contents for HP Compaq Mini 700

  • Page 1 HP Mini 1000 Netbook Compaq Mini 700 Netbook Maintenance and Service Guide...
  • Page 2 Corporation. SD Logo is a trademark of its proprietor. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.
  • Page 3 Safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the device, do not place the device directly on your lap or obstruct the device air vents. Use the device only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow.
  • Page 4 Safety warning notice...

  • Page 5: Table Of Contents

    Table of contents 1 Product description 2 External component identification Top components ... 4 Display ... 4 Wireless antennae ... 5 Keys ... 6 TouchPad ... 7 Front components ... 8 Right-side components ... 9 Left-side components ... 10 Bottom components ... 11 3 Illustrated parts catalog Serial number location ...
  • Page 6 Unknown user password ... 34 Component replacement procedures ... 35 Service tag ... 35 Device feet ... 36 Battery ... 37 Memory module ... 38 Keyboard ... 40 Mass storage devices ... 42 Top cover ... 45 WLAN module ... 48 WWAN module ...
  • Page 7 System interrupt specifications ... 80 System I/O address specifications ... 81 System memory map specifications ... 83 7 Screw listing Phillips PM1.6×2.5 screw ... 84 Phillips PM1.6×4.0 screw ... 85 Phillips PM1.6×6.0 screw ... 86 Phillips PM2.0×3.0 screw ... 87 Phillips PM2.0×4.5 screw ...
  • Page 8 viii...

  • Page 9: Product Description

    Chipset Graphics Panels Memory Description HP Mini 1000 Netbook Compaq Mini 700 Netbook Intel® Atom™ N270 1.6-GHz processor, 512-KB Level 2 cache, 533-MHz front-side bus (FSB) Northbridge: 945GSE; 533-MHz bus speed Southbridge: ICH7M Intel® Graphics Media Accelerator 950 Universal Memory Architecture (UMA) graphics...
  • Page 10 Integrated 10/100 network interface card (NIC) 2 WLAN antennae built into display assembly Integrated WLAN by way of Broadcom BCM4312 802.11b/g WLAN module Integrated WWAN by way of HP un2400 Mobile Broadband Module (optional) Integrated personal area network (PAN) by way of Bluetooth® module (optional)
  • Page 11 30-W UMA AC adapter (non-smart) with localized cable plug support AC adapter connector on cable 3-cell lithium-polymer (Li-Pol) battery (2.4-Ah, 26-Wh), 3-hour target life Security Supports HP Kensington Security Lock Operating system Preinstalled: Windows® XP Home SP3, ultra low-cost personal computer (ULCPC) edition Restore media:...

  • Page 12: External Component Identification

    External component identification Top components Display Item Component Internal display switch Speakers (2) Internal microphone Webcam Chapter 2 External component identification Function Turns off the display if the display is closed while the power is on. Produce sound. Records and captures sound. Captures still photographs and videos.

  • Page 13: Wireless Antennae

    Wireless antennae Item Component WLAN antennae (2) * WWAN antennae (2) (select models only) * * The antennae are not visible from the outside of the device. For optimal transmission, keep the areas immediately around the antennae free from obstructions. To see wireless regulatory notices, refer to the section of the Regulatory, Safety and Environmental Notices that applies to your country or region.

  • Page 14: Keys

    Keys Item Component Function keys Windows logo key Windows applications key Chapter 2 External component identification Function Displays system information when pressed in combination with the key. Execute frequently used system functions when pressed in combination with the key. Executes frequently used system functions when pressed in combination with a function key.

  • Page 15: Touchpad

    TouchPad Item Component TouchPad on/off button TouchPad on/off light Left TouchPad button * TouchPad * TouchPad scroll zone Right TouchPad button * * This table describes factory settings. To view or change pointing device preferences, select Start > Control Panel > Printers and Other Hardware >...

  • Page 16: Front Components

    Front components Item Component Power light Power switch Drive light Battery light Wireless light Wireless switch Chapter 2 External component identification Function ● On: The device is on. ● Blinking: The device is in Standby. ● Off: The device is off. ●...

  • Page 17: Right-Side Components

    Right-side components Item Component Vent SD Card Reader USB port HP Mini Mobile Drive Bay (on models equipped with a solid-state drive) Security cable connector Function Enables airflow to cool internal components NOTE: The device fan starts up automatically to cool internal components and prevent overheating.

  • Page 18: Left-Side Components

    Left-side components Item Component Power connector Power connector light USB port Vent Expansion port Audio-out (headphone) jack/Audio-in (microphone) jack RJ-45 (network) jack Chapter 2 External component identification Function Connects an AC adapter. ● On: The device is running on AC power. ●...

  • Page 19: Bottom Components

    Bottom components Item Component Battery bay Battery release latches (2) Memory module compartment Vent Function Holds the battery. Release the battery from the battery bay. Contains the memory module slot. NOTE: The release latch for the memory module compartment cover (not illustrated) is located underneath the right battery release latch (see Memory module on page...

  • Page 20: Illustrated Parts Catalog

    Illustrated parts catalog Serial number location The service tag, affixed to the bottom of the device, provides information that may be needed when troubleshooting system problems. The service tag provides the following information: (1) Product name: This is the product name affixed to the front of the device. (2) Serial number (s/n): This is an alphanumeric identifier that is unique to each product.

  • Page 21: Device Major Components

    Display assembly (includes 1 webcam, 1 microphone, 1 speaker box, and 2 WLAN antenna transceivers/cables; WWAN is optional) 8.9-inch WSVGA BrightView (HP Mini 1000) 8.9-inch WSVGA BrightView (Compaq Mini 700) 10.1-inch standard-definition AntiGlare (HP Mini 1000) 10.1-inch standard-definition AntiGlare (red-colored HP Mini 1000) 10.1-inch standard-definition AntiGlare (Compaq Mini 700)
  • Page 22 NOTE: For a comprehensive list of keyboard spare part numbers, see the on page For use with standard device models For use with red-colored HP Mini 1000 models only Top cover (includes TouchPad) Mass storage devices NOTE: Each hard drive spare part kit and solid-state drive spare part kit includes a cable and bracket.
  • Page 23 Memory module compartment cover (9c) SD Card Reader slot bezel (9d) Security cable connector For the HP Mini 1000 and Compaq Mini 700 For the red-colored HP Mini 1000 (10) RTC battery (11) System board (includes processor and replacement thermal material)
  • Page 24 Battery (3-cell, 26-Wh Li-Pol) For the HP Mini 1000 and Compaq Mini 700 For the red-colored HP Mini 1000 (for use in all countries and regions except Germany) For the red-colored HP Mini 1000 (for use in Germany only) Chapter 3 Illustrated parts catalog...

  • Page 25: Display Assembly Components

    10.2-inch display assembly components are not sold separately. The complete display assembly is available as spare part number 512140-001 for the red-colored HP Mini 1000, 507310-001 for all other models of the HP Mini 1000, or 512143-001 for the Compaq Mini 700. Item...
  • Page 26 For use with 10.1-inch panels on the Compaq Mini 700 Display panel 8.9-inch WSVGA BrightView for the HP Mini 1000 and the Compaq Mini 700 10.1-inch standard-definition AntiGlare for the Compaq Mini 700 Display Cable Kit (includes microphone assembly and display/webcam cable) For use with all 8.9-inch panels;...

  • Page 27: Cable Kit

    Cable Kit Item Description Cable Kit: SIM card cable Power cable Internal display switch module Bluetooth cable USB cable Spare part number 507708-001 Cable Kit...

  • Page 28: Mass Storage Devices

    Mass storage devices NOTE: Each hard drive spare part kit and solid-state drive spare part kit includes a cable and bracket. Item Description Mass storage devices: Hard drive (select models only): 60-GB, 4200-rpm Hard Drive Hardware Kit (not illustrated) Solid-state drive 16-GB 8-GB Chapter 3 Illustrated parts catalog...

  • Page 29: Plastics Kit

    Plastics Kit Item Description Plastics Kit: For the HP Mini 1000 and Compaq Mini 700 For the red-colored HP Mini 1000 Memory module compartment cover HP Mini Mobile Drive Bay cover Security cable connector SD Card Reader slot bezel Spare part number...

  • Page 30: Miscellaneous Parts

    ● RJ-45 connector bracket ● USB connector bracket ● WWAN connector bracket HP Mini Mobile Drive (supported on models equipped with a solid-state drive and HP Mini Mobile Drive Bay) 2-GB 4-GB 8-GB HP Mini Sleeve For the HP Mini 1000...
  • Page 31 Description Screw Kit ● Phillips PM1.6×2.5 screw ● Phillips PM1.6×4.0 screw ● Phillips PM1.6×6.0 screw ● Phillips PM2.0×3.0 screw ● Phillips PM2.0×4.5 screw ● Phillips PM2.5×5.0 screw ● Phillips PM2.5×7.0 screw 30-W UMA AC adapter For use in all countries and regions except Germany For use in Germany only Spare part number 504614-001...

  • Page 32: Sequential Part Number Listing

    Spare part Description number 483377-002 HP un2400 Mobile Broadband Module 490371-001 Power cord for use in North America (HP Mini 1000 only) 490371-011 Power cord for use in Australia (HP Mini 1000 only) 490371-021 Power cord for use in Europe 490371-031...
  • Page 33 Display Cable Kit, spare part number 504597-001 (with WLAN) or 504598-001 (with WWAN). 504595-001 Display enclosure (includes logo) for use with 8.9-inch panels on the HP Mini 1000 504596-001 Display Hinge Kit for use with all 8.9-inch panels (includes left/right display hinges and display panel...
  • Page 34 Speaker assembly (includes left and right cables) 506336-001 USB board 506337-001 Base enclosure (includes 4 rubber feet) for the HP Mini 1000 and Compaq Mini 700 506338-001 Speaker grill for the HP Mini 1000 and Compaq Mini 700 507309-001 8.9-inch WSVGA BrightView display assembly for the HP Mini 1000 (includes 1 webcam, 1 microphone, 1 speaker box, and 2 WLAN antenna transceivers/cables;...
  • Page 35 512331-001 HP Mini Mobile Drive, 8-GB 512851-001 3-cell, 26-Wh Li-Pol battery for the red-colored HP Mini 1000 (for use in all countries and regions except Germany) 512851-002 3-cell, 26-Wh Li-Pol battery for the red-colored HP Mini 1000 (for use in Germany only)
  • Page 36 Description number 515208-001 Display Cable Kit with WLAN for use with 10.1-inch panels on the Compaq Mini 700 (includes microphone assembly and display/webcam cable) 515209-001 Display Cable Kit with WWAN for use with 10.1-inch panels on the Compaq Mini 700 (includes microphone...

  • Page 37: Removal And Replacement Procedures

    Removal and replacement procedures Preliminary replacement requirements Tools required You will need the following tools to complete the removal and replacement procedures: ● Flat-bladed screwdriver ● Magnetic screwdriver ● Phillips P0 and P1 screwdrivers Service considerations The following sections include some of the considerations that you must keep in mind during disassembly and assembly procedures.

  • Page 38: Drive Handling

    Drive handling CAUTION: Drives are fragile components that must be handled with care. To prevent damage to the device, damage to a drive, or loss of information, observe these precautions: Before removing or inserting a hard drive, shut down the device. If you are unsure whether the device is off or in Hibernation, turn the device on, and then shut it down through the operating system.

  • Page 39: Grounding Guidelines

    Grounding guidelines Electrostatic discharge damage Electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure determine the degree of sensitivity. Networks built into many integrated circuits provide some protection, but in many cases, ESD contains enough power to alter device parameters or melt silicon junctions. A discharge of static electricity from a finger or other conductor can destroy static-sensitive devices or microcircuitry.

  • Page 40: Packaging And Transporting Guidelines

    Packaging and transporting guidelines Follow these grounding guidelines when packaging and transporting equipment: ● To avoid hand contact, transport products in static-safe tubes, bags, or boxes. ● Protect ESD-sensitive parts and assemblies with conductive or approved containers or packaging. ● Keep ESD-sensitive parts in their containers until the parts arrive at static-free workstations.

  • Page 41: Equipment Guidelines

    Equipment guidelines Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation. ● When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps with a minimum of one megohm ±10% resistance in the ground cords. To provide proper ground, wear a strap snugly against the skin at all times.

  • Page 42: Unknown User Password

    Unknown user password If the device you are servicing has an unknown user password, follow these steps to clear the password: NOTE: These steps also clear CMOS. Shut down the device. If you are unsure whether the device is off or in Hibernation, turn the device on, and then shut it down through the operating system.

  • Page 43: Component Replacement Procedures

    Component replacement procedures This chapter provides removal and replacement procedures. There are as many as 49 screws, in 7 different sizes, that must be removed, replaced, or loosened when servicing the device. Make special note of each screw size and location during removal and replacement. Service tag The service tag, affixed to the bottom of the device, provides information that may be needed when troubleshooting system problems.

  • Page 44: Device Feet

    Device feet The device feet are adhesive-backed rubber pads. The feet are included in the Rubber Kit, spare part number 504613-001. There are 4 rubber feet that are installed on the base enclosure in the locations illustrated below. Chapter 4 Removal and replacement procedures...

  • Page 45: Battery

    3-cell, 26-Wh Li-Pol battery for the red-colored HP Mini 1000 (for use in all countries and regions except Germany) 3-cell, 26-Wh Li-Pol battery for the red-colored HP Mini 1000 (for use in Germany only) Before disassembling the device, follow these steps: Shut down the device.

  • Page 46: Memory Module

    Remove the cover (2). The memory module compartment cover is included in the Plastics Kit, spare part number 512192-001 for the red-colored HP Mini 1000 or 507317-001 for all other models of the HP Mini 1000 and the Compaq Mini 700.
  • Page 47 Remove the memory module (2) by pulling the module away from the slot at an angle. NOTE: Memory modules are designed with a notch (3) to prevent incorrect insertion into the memory module slot. Reverse this procedure to install a memory module. Component replacement procedures...

  • Page 48: Keyboard

    Turn the device display-side up, with the front toward you. Open the device as far as possible. Chapter 4 Removal and replacement procedures Spare part number Description 504611-xx1 For use with red-colored HP Mini 1000 models only Battery on page 37). Sequential part number listing Spare part number 509650-xx1...
  • Page 49 Grasp the tabs (1) on the outer edges of the keyboard and lift the rear edge (2) until the keyboard rests at an angle. Then slide the keyboard back until it rests on the display assembly (3). Release the zero insertion force (ZIF) connector (1) to which the keyboard cable is attached. Disconnect the cable (2), and then remove the keyboard.

  • Page 50: Mass Storage Devices

    Mass storage devices NOTE: Each hard drive spare part kit and solid-state drive spare part kit includes a cable and bracket. Description 8-GB solid-state drive 16-GB solid-state drive 60-GB, 4200-rpm hard drive Before removing the hard drive or solid-state drive, follow these steps: Shut down the device.
  • Page 51 Lift the hard drive (4) up and slide it out of the drive bay. Reverse this procedure to install the hard drive. To remove the solid-state drive: Release the ZIF connector (1) to which the SIM card cable is attached. The end of the cable lies across the top of the solid-state drive.
  • Page 52 Remove the drive bracket (4) from the drive bay. Remove the three Phillips PM2.0×3.0 screws (1) that secure the solid-state drive to the bracket. Remove the solid-state drive (2) from the bracket. Reverse this procedure to install the solid-state drive. Chapter 4 Removal and replacement procedures...

  • Page 53: Top Cover

    Top cover Description Top cover (includes TouchPad) Before removing the top cover, follow these steps: Shut down the device. If you are unsure whether the device is off or in Hibernation, turn the device on, and then shut it down through the operating system. Disconnect all external devices connected to the device.
  • Page 54 Open the device as far as possible. Remove the Phillips PM2.0×4.5 screw (1) and the Phillips PM2.5×5.0 screw (2) that secure the top cover to the base enclosure. Lift the rear edge of the top cover (1) and swing it up. Then slide the top cover back slightly to rest against the display assembly (2) at an angle.
  • Page 55 Disconnect the TouchPad button board cable (2) from the system board, and then remove the top cover. Reverse this procedure to install the top cover. Component replacement procedures...

  • Page 56: Wlan Module

    WLAN module Description Broadcom 4312 802.11/b/g WLAN module for use in Canada, the Cayman Islands, Guam, Puerto Rico, the U.S. Virgin Islands, and the United States Broadcom 4312 802.11/b/g WLAN module for use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cameroon, Cape Verde, the Central African Republic, Chad, Chile,...
  • Page 57 Remove the WLAN module: Detach the black Mylar covering (not illustrated) that surrounds the fan. Several system cables are routed through a channel between the fan and the battery bay. Detach the black tape from the cables. Disconnect the wireless antenna cables (1) from the terminals on the WLAN module. Remove the Phillips PM2.0×3.0 screw (2) that secures the WLAN module to the system board.

  • Page 58: Wwan Module

    WWAN module Description HP un2400 Mobile Broadband Module CAUTION: The WWAN module and the WLAN module are not interchangeable. To prevent an unresponsive system, replace the wireless module only with a wireless module authorized for use in the device by the governmental agency that regulates wireless devices in your country or region.
  • Page 59 Remove the WWAN module: Detach the black Mylar covering from the WWAN module. The covering is secured by adhesive. Detach the aluminum foil and tape (not illustrated) from the wireless antenna cables, and then disconnect the wireless antenna cables (1) from the terminals on the WWAN module. NOTE: The red WWAN antenna cable is connected to the WWAN module “Main”...

  • Page 60: Rtc Battery

    RTC battery Description RTC battery NOTE: Removing the RTC battery and leaving it uninstalled for 5 or more minutes causes all passwords and CMOS settings to be cleared. Before removing the real-time clock (RTC) battery, follow these steps: Shut down the device. If you are unsure whether the device is off or in Hibernation, turn the device on, and then shut it down through the operating system.

  • Page 61: Bluetooth Module

    Bluetooth module NOTE: The Bluetooth module spare part kit does not include a Bluetooth module cable. The Bluetooth module cable is included in the Cable Kit, spare part number 507708-001. Description Bluetooth module Before removing the Bluetooth module, follow these steps: Shut down the device.

  • Page 62: System Board

    System board NOTE: The system board spare part kit includes a processor and replacement thermal material. Description System board equipped with 1.6-GHz processor Before removing the system board, follow these steps: Shut down the device. If you are unsure whether the device is off or in Hibernation, turn the device on, and then shut it down through the operating system.
  • Page 63 Disconnect the following cables from the system board: (1) Speaker cables (2) Microphone cable (3) Fan cable (4) Power cable (5) Display panel cable Remove the two Phillips PM1.6×2.5 screws (1) that secure the actuators for the power switch and wireless on/off switch to the system board.
  • Page 64 Remove the USB connector bracket (2). NOTE: The USB connector bracket is included in the Bracket Kit, spare part number 507318-001. Remove the Phillips PM2.0×4.5 screw that secures the system board to the base enclosure. Chapter 4 Removal and replacement procedures...

  • Page 65: Heat Sink Assembly

    Grasp the system board at its midpoint (1) and lift the right side (2) up. Then remove the system board (3) from the base enclosure. Reverse the procedure to install the system board. Heat sink assembly NOTE: The heat sink assembly spare part kit includes replacement thermal material. Description Heat sink assembly Before removing the heat sink assembly, follow these steps:...
  • Page 66 Remove the heat sink assembly (2). NOTE: Due to the adhesive quality of the thermal material located between the heat sink assembly and system board components, it may be necessary to move the heat sink assembly from side to side to detach the assembly. NOTE: The thermal material must be thoroughly cleaned from the surfaces of the heat sink assembly and the system board each time the heat sink assembly is removed.

  • Page 67: Fan

    Description NOTE: To properly ventilate the device, allow at least a 7.6-cm (3-inch) clearance on the left side of the device. The device uses an electric fan for ventilation. The fan is controlled by a temperature sensor and is designed to turn on automatically when high temperature conditions exist. These conditions are affected by high external temperatures, system power consumption, power management/battery conservation configurations, battery fast charging, and software requirements.
  • Page 68 Remove the fan (3). Reverse this procedure to install the fan. Chapter 4 Removal and replacement procedures...

  • Page 69: Usb Board And Internal Display Switch

    USB board and internal display switch NOTE: The internal display switch module is included in the Cable Kit, spare part number 507708-001. Description USB board Before removing the USB board, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
  • Page 70 Detach the SIM card cable (3). The SIM card cable is attached to the battery bay with tape. Reverse this procedure to install the USB board. If it is necessary to replace the internal display switch module, perform the following steps: Remove the Phillips PM2.0×3.0 screw (1) that secures the internal display switch bracket to the base enclosure.

  • Page 71: Display Assembly

    10.2-inch display assembly components are not sold separately. The complete display assembly is available as spare part number 512140-001 for the red-colored HP Mini 1000, 507310-001 for all other models of the HP Mini 1000, or 512143-001 for the Compaq Mini 700. Description 8.9-inch, WSVGA, BrightView (HP Mini 1000)
  • Page 72 Remove the two Phillips PM2.0×4.5 screws (1) that secure the speaker assembly to the display enclosure. All display assembly subcomponent screws are available in the Display Screw Kit, spare part number 509700-001 for all 8.9-inch panels or 515211-001 for 10.1-inch panels (Compaq Mini 700 only). Chapter 4 Removal and replacement procedures...
  • Page 73 Remove the hinges (2). The hinges are available in the Display Hinge Kit, spare part number 504596-001 for all 8.9-inch panels or 515207-001 for 10.1-inch panels (Compaq Mini 700 only). If it is necessary to replace the display bezel, perform the following steps: Flex the inside edges of the bottom (1), left and right sides (2), and the top (3) of the display bezel until the bezel disengages from the display enclosure.
  • Page 74 Remove the display bezel (4). The spare part numbers for the 8.9-inch display bezels are 506333-001 (HP Mini 1000) and 509701-001 (Compaq Mini 700). The spare part number for the 10.1-inch display bezel is 509704-001 (Compaq Mini 700 only). If it is necessary to replace the webcam module, perform the following steps: Open the tab built into the display enclosure shielding that secures the microphone cable, and then release the microphone (1) from its clip.
  • Page 75 Remove the webcam module (2). The webcam module is available as spare part number 504594-001 for all 8.9-inch panels or 515213-001 for 10.1-inch panels (Compaq Mini 700 only). If it is necessary to replace the display panel, perform the following steps: Remove the nine Phillips PM2.0×3.0 screws that secure the display panel to the display...
  • Page 76 Remove the display panel (3) from the display enclosure. An 8.9-inch display panel for the HP Mini 1000 and the Compaq Mini 700 is available as spare part number 509698-001. A 10.1-inch display panel for the Compaq Mini 700 only is available as spare part number 509703-001.
  • Page 77 Cable Kit, spare part number 504597-001 (with WLAN) or 504598-001 (with WWAN). The wireless antenna transceivers and cables for 10.1-inch panels (Compaq Mini 700 only) are available in the Display Cable Kit, spare part number 515208-001 (with WLAN) or 515209-001 (with WWAN).

  • Page 78: Setup Utility

    Setup Utility Starting the Setup Utility The Setup Utility is a ROM-based information and customization utility that can be used even when your Windows operating system is not working. The utility reports information about the device and provides settings for startup, security, and other preferences.

  • Page 79: Navigating And Selecting In The Setup Utility

    Navigating and selecting in the Setup Utility Because the Setup Utility is not Windows based, it does not support the TouchPad. Navigation and selection are by keystroke. ● To choose a menu or a menu item, use the arrow keys. ●...

  • Page 80: Exiting The Setup Utility

    Exiting the Setup Utility You can exit the Setup Utility with or without saving changes. ● To exit the Setup Utility and save your changes from the current session: If the Setup Utility menus are not visible, press keys to select Exit > Exit Saving Changes, and then press enter. ●...

  • Page 81: System Configuration Menu

    System Configuration menu Select Language Support Processor C4 State Boot Options Diagnostics menu Select Hard Disk Self Test (select models only) Memory Test To do this Change the Setup Utility language. Enable/disable the processor C4 sleep state. Set the following boot options: ●...

  • Page 82: Specifications

    Specifications Device specifications Dimensions Depth Width Height Weight 10.2-in. LCD, equipped with a 3-cell battery, 60-GB hard drive, 1-GB memory, WLAN module, and 2 wireless antennae 10.2-in. LCD, equipped with a 3-cell battery, 8-GB solid-state drive, 1-GB memory, WLAN module, and 2 wireless antennae 8.9-in.

  • Page 83: 8.9-Inch, Wsvga, Brightview Display Specifications

    8.9-inch, WSVGA, BrightView display specifications Dimensions Height Width Diagonal Number of colors Contrast ratio Brightness Pixel resolution Pitch Format Configuration Backlight Character display Total power consumption Viewing angle Metric 11.34 cm 19.51 cm 22.61 cm 262,144 300:1 (typical) 200 nits (typical) 0.1905 ×...

  • Page 84: Inch, Standard-Definition, Antiglare Display Specifications

    10.1-inch, standard-definition, AntiGlare display specifications Dimensions Height Width Diagonal Number of colors Contrast ratio Brightness Pixel resolution Pitch Format Configuration Backlight Character display Total power consumption Viewing angle Chapter 6 Specifications Metric U.S. 23.45 cm 9.23 in 14.30 cm 5.62 in 25.55 cm 10.05 in 262,144...

  • Page 85: 10.2-Inch, Wsvga, Antiglare Display Specifications

    10.2-inch, WSVGA, AntiGlare display specifications Dimensions Height Width Diagonal Number of colors Contrast ratio Brightness Pixel resolution Pitch Format Configuration Backlight Character display Total power consumption Viewing angle Metric 12.53 cm 22.27 cm 25.55 cm 262,144 400:1 (typical) 200 nits (typical) 0.2175 ×...

  • Page 86: Hard Drive Specifications

    Hard drive specifications Dimensions Height Width Weight Interface type Transfer rate Security Seek times (typical read, including setting) Single track Average Maximum Logical blocks Disc rotational speed Operating temperature * 1 GB = 1 billion bytes when referring to hard drive storage capacity. Actual accessible capacity is less. Actual drive specifications may differ slightly.

  • Page 87: Solid-State Drive Specifications

    Solid-state drive specifications Performance Transfer modes supported Sustained read Sustained write Characteristics Interface MLC NAND flash capacity Electrical specifications DC supply voltage Standby current Active current Environmental specifications Operating temperature Storage temperature Operating altitude Humidity Shock Acoustic noise Vibration Physical specifications Connector Weight (8-GB model) Weight (16-GB model)

  • Page 88: System Dma Specifications

    System DMA specifications Hardware DMA DMA0 DMA1 * DMA2 * DMA3 DMA4 System interrupt specifications Hardware IRQ IRQ0 IRQ1 IRQ8 IRQ9 * IRQ12 IRQ13 IRQ14 IRQ15 IRQ16 IRQ17 IRQ18 IRQ19 IRQ23 * Default configuration Chapter 6 Specifications System function Not applicable Not applicable Not applicable Not applicable...

  • Page 89: System I/O Address Specifications

    System I/O address specifications I/O address (hex) 000 - 00F 000 - CF7 010 - 01F 020 - 021 022 - 03F 040 - 043 044 - 05F 060 - 060 061 - 061 062 - 062 063- 063 064 - 064 065 - 065 066 - 066 067 - 06F...
  • Page 90 I/O address (hex) 279 - 279 3B0 - 3BB 3C0 - 3DF 3F6 - 3F6 400 - 41F 480 - 4BF 4D0 - 4D1 500 - 501 800 - 87F A79 - A79 0D00 - FFFF D480 - D49F D800 - D81F D880 - D89F DC00 - DC1F DC80 - DC87...

  • Page 91: System Memory Map Specifications

    System memory map specifications Memory address 00000000 - 0009FFFF 000A0000 - 000BFFFF 000A0000 - 000BFFFF 000C0000 - 000CFFFF 000D0000 - 000DFFFF 000E0000 - 000FFFFF 00100000 - 3F7FFFFF 3F800000 - DFFFFFFF D0000000 - DFFFFFFF E0000000 - E3FFFFFF E4000000 - FED8FFFF FE880000 - FE8FFFFF FE937C00 - FE937FFF FE938000 - FE93BFFF FE940000 - FE97FFFF...

  • Page 92: Screw Listing

    All screws listed in this section are available in the Screw Kit, spare part number 504614-001; or in the Display Screw Kit, spare part number 509700-001 for all 8.9-inch panels or 515211-001 for 10.1-inch panels (Compaq Mini 700 only). Phillips PM1.6×2.5 screw...

  • Page 93: Phillips Pm1.6×4.0 Screw

    Where used: Two screws that secure the heat sink to the system board Phillips PM1.6×4.0 screw Color Silver Where used: One screw that secures the keyboard to the device Quantity Length 4.0 mm Thread Head diameter 1.60 mm 3.5 mm Phillips PM1.6×4.0 screw...

  • Page 94: Phillips Pm1.6×6.0 Screw

    Phillips PM1.6×6.0 screw Color Black Where used: One screw that secures the keyboard to the device Chapter 7 Screw listing Quantity Length 6.0 mm Thread Head diameter 1.60 mm 3.5 mm...

  • Page 95: Phillips Pm2.0×3.0 Screw

    Phillips PM2.0×3.0 screw Color Black Where used: Three screws that secure the solid-state drive to its bracket Where used: One screw that secures the WLAN module to the system board Quantity Length 24 (WLAN only) 3.0 mm 25 (with WWAN) Thread Head diameter 2.0 mm...
  • Page 96 Where used: One screw that secures the WWAN connector bracket to the system board Where used: Two screws that secure the USB connector bracket to the system board Where used: One screw that secures the fan to the base enclosure Chapter 7 Screw listing...
  • Page 97 Where used: One screw that secures the DC jack bracket to the base enclosure Where used: One screw that secures the internal display switch bracket to the base enclosure Where used: Two screws that secure the webcam module to the display enclosure Phillips PM2.0×3.0 screw...
  • Page 98 Where used: Nine screws that secure the display panel to the display enclosure Where used: Four screws that secure the left and right display panel brackets to the display panel Chapter 7 Screw listing...

  • Page 99: Phillips Pm2.0×4.5 Screw

    Phillips PM2.0×4.5 screw Color Silver Where used: Two screws that secure the hard drive to the device Where used: Two screws that secure the solid-state drive bracket to the device Quantity Length 4.5 mm Thread Head diameter 2.0 mm 4.0 mm Phillips PM2.0×4.5 screw...
  • Page 100 Where used: One screw that secures the top cover to the device Where used: One screw that secures the fan and DC jack bracket to the base enclosure Where used: Two screws that secure the speaker assembly to the display enclosure Chapter 7 Screw listing...

  • Page 101: Phillips Pm2.5×5.0 Screw

    Where used: Four screws that secure the display hinges to the display assembly Phillips PM2.5×5.0 screw Color Silver Where used: Four screws that secure the display assembly and top cover to the device Quantity Length 5.0 mm Thread Head diameter 2.5 mm 4.5 mm Phillips PM2.5×5.0 screw...

  • Page 102: Phillips Pm2.5×7.0 Screw

    Phillips PM2.5×7.0 screw Color Black Where used: Four screws that secure the top cover to the base enclosure Chapter 7 Screw listing Quantity Length 7.0 mm Thread Head diameter 2.5 mm 4.0 mm...

  • Page 103: Backup And Recovery

    Backing up your information NOTE: You can recover only the files that you have previously backed up. HP recommends that you use the Windows backup utility to create a hard drive backup as soon as you set up your device.

  • Page 104: Backup Suggestions

    Backup suggestions ● Connect the device to external power before performing backup and recovery procedures. ● Create system recovery points. ● Store personal files in the My Documents folder and back up these folders periodically. ● Back up templates stored in their associated programs. ●...

  • Page 105: Backing Up All Files And Folders

    The first system recovery point, a snapshot of the entire image, is automatically created the first time you perform a backup. Subsequent recovery points make copies of changes made after that time. HP recommends that you create recovery points at the following times: ● Before you add or extensively modify software or hardware ●...

  • Page 106: Scheduling Backups

    Scheduling backups You can schedule backups for the entire system, for recovery points, or for specific files and folders. Backups can be scheduled at specific intervals (daily, weekly, or monthly) or at specific events, such as at system restart or when you log on. To schedule backups: Select Start >...

  • Page 107: Connector Pin Assignments

    Connector pin assignments Audio-in (microphone) Audio-out (headphone) Signal Audio signal in Audio signal in Ground Signal Audio out, left channel Audio out, right channel Ground Audio-in (microphone)

  • Page 108: Network)

    RJ-45 (network) Universal Serial Bus 100 Chapter 9 Connector pin assignments Signal Transmit + Transmit - Receive + Unused Unused Receive - Unused Unused Signal +5 VDC Data - Data + Ground...

  • Page 109: 10 Power Cord Set Requirements

    10 Power cord set requirements The wide range input feature of the device permits it to operate from any line voltage from 100 to 120 volts AC or from 220 to 240 volts AC. The 3-conductor power cord set included with the device meets the requirements for use in the country or region where the equipment is purchased.

  • Page 110: Requirements For Specific Countries And Regions

    Requirements for specific countries and regions Country/region Australia Austria Belgium Canada Denmark Finland France Germany Italy Japan The Netherlands Norway The People's Republic of China South Korea Sweden Switzerland Taiwan The United Kingdom The United States The flexible cord must be Type HO5VV-F, 3-conductor, 1.0-mm² conductor size. Power cord set fittings (appliance coupler and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used.

  • Page 111: 11 Recycling

    When you remove these components, handle them carefully. NOTE: Materials Disposal. This HP product contains mercury in the backlight in the display assembly that might require special handling at end-of-life. Disposal of mercury may be regulated because of environmental considerations. For disposal or recycling information, contact your local authorities, or see the Electronic Industries Alliance (EIA) Web site at http://www.eiae.org.
  • Page 112 Perform the following steps to disassemble the display assembly: Remove all screw covers (1) and screws (2) that secure the display bezel to the display assembly. Lift up and out on the left and right inside edges (1) and the top and bottom inside edges (2) of the display bezel until the bezel disengages from the display assembly.
  • Page 113 Disconnect all display panel cables (1) from the display inverter and remove the inverter (2). Remove all screws (1) that secure the display panel assembly to the display enclosure. Remove the display panel assembly (2) from the display enclosure. Turn the display panel assembly upside down. Remove all screws that secure the display panel frame to the display panel.
  • Page 114 Remove the display panel frame (2) from the display panel. Remove the screws (1) that secure the backlight cover to the display panel. Lift the top edge of the backlight cover (2) and swing it outward. Remove the backlight cover. Turn the display panel right-side up.
  • Page 115 Remove the backlight cables (1) from the clip (2) in the display panel. Turn the display panel upside down. WARNING! The backlight contains mercury. Exercise caution when removing and handling the backlight to avoid damaging this component and causing exposure to the mercury. Remove the backlight frame from the display panel.
  • Page 116 Remove the backlight from the backlight frame. Disconnect the display panel cable (1) from the LCD panel. Remove the screws (2) that secure the LCD panel to the display rear panel. Release the LCD panel (3) from the display rear panel. Release the tape (4) that secures the LCD panel to the display rear panel.

  • Page 117: Index

    Index AC adapter, spare part number 23, 24 antenna locations 5 removal 69 spare part number 18, 69 audio, product description 2 audio-in jack location 10 pin assignments 99 audio-out jack location 10 pin assignments 99 base enclosure, spare part number 15, 26, 27 battery location 11...
  • Page 118 57 spare part number 57 HP Mini Mobile Drive Bay, location 9 HP Mini Mobile Drive, spare part number 22 I/O address specifications 81 in Setup Utility 70 internal display switch 4 internal media cards, product...
  • Page 119 product description audio 2 chipset 1 diskette drive 2 Ethernet 2 expansion port 3 external media cards 2 flash storage drive 2 graphics 1 hard drive 2 internal media cards 2 keyboard 3 mass storage device 2 memory module 1 modem 2 operating system 3 optical drive 2...
  • Page 120 Windows applications key 6 Windows logo key 6 wireless antenna locations 5 removal 69 spare part number 18, 69 wireless antenna components 5 wireless light 8 wireless module, product description 2 wireless switch 8 WLAN module removal 48 spare part number 14, 24, workstation guidelines 32 WWAN module removal 50...

This manual is also suitable for:

Compaq mini 701Compaq mini 702Compaq mini 703Mini 11401035nr - mini - atom 1.6 ghz700ed - hqrp heavy-duty ac adapter ... Show all

Table of Contents