HP Mini 1000 Maintenance And Service Manual

Hp mini 1000: supplementary guide.
Hide thumbs
HP Mini 1000 Netbook
Maintenance and Service Guide

Advertising

   Related Manuals for HP Mini 1000

   Summary of Contents for HP Mini 1000

  • Page 1

    HP Mini 1000 Netbook Maintenance and Service Guide...

  • Page 2

    Corporation. SD Logo is a trademark of its proprietor. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.

  • Page 3

    Safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the device, do not place the device directly on your lap or obstruct the device air vents. Use the device only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow.

  • Page 4

    Safety warning notice...

  • Page 5: Table Of Contents

    Table of contents 1 Product description 2 External component identification Top components ... 4 Display ... 4 Wireless antennae ... 5 Keys ... 6 TouchPad ... 7 Front components ... 8 Right-side components ... 9 Left-side components ... 10 Bottom components ... 11 3 Illustrated parts catalog Serial number location ...

  • Page 6: Table Of Contents

    Component replacement procedures ... 30 Service tag ... 30 Device feet ... 31 Battery ... 32 Memory module ... 33 Keyboard ... 35 Mass storage devices ... 37 Top cover ... 40 WLAN module ... 43 RTC battery ... 45 Bluetooth module ...

  • Page 7: Table Of Contents

    Backing up your information ... 93 When to back up ... 93 Restoring your information ... 94 Using System Restore ... 94 Using HP MIE Restore Image Creator ... 95 9 Connector pin assignments Audio-in (microphone) ... 100 Audio-out (headphone) ... 100 RJ-45 (network) ...

  • Page 8

    viii...

  • Page 9: Product Description

    2048-MB total system memory (2048 × 1) Solid-state drive (SSD) based on multi-level cell (MLC) technology Configurations: 8-GB, 16-GB Models equipped with a solid-state drive also support the HP Mini Mobile Drive Supports all 4.57-cm (1.8-inch) parallel ATA (PATA) hard drives (optional) Configuration: 60-GB, 4200-rpm...

  • Page 10

    Integrated personal area network (PAN) by way of Bluetooth® module (optional) SD Card Reader supporting MultiMediaCard (MMC) and Secure Digital (SD) Memory Card HP Mini Mobile Drive (on models equipped with a solid-state drive) Two Mini Card slots: ● Full-size Mini Card slot ●...

  • Page 11

    Category Security Operating system Serviceability Description Supports security lanyard Preinstalled: HP Mobile Internet Experience (MIE) Restore media: Backup software provided by operating system CD and recovery DVD End-user replaceable parts: AC adapter Battery (system) Memory module HP Mini Mobile Drive...

  • Page 12: Top Components, Display

    External component identification Top components Display Item Component Internal display switch Speakers (2) Internal microphone Webcam Chapter 2 External component identification Function Turns off the display if the display is closed while the power is on. Produce sound. Records and captures sound. Captures still photographs and videos.

  • Page 13: Wireless Antennae

    Wireless antennae Component WLAN antennae (2) * * The antennae are not visible from the outside of the device. For optimal transmission, keep the areas immediately around the antennae free from obstructions. To see wireless regulatory notices, refer to the section of the Regulatory, Safety and Environmental Notices that applies to your country or region.

  • Page 14: Keys

    Keys Item Component Function keys Home key Program Switcher key Chapter 2 External component identification Function Displays system information when pressed in combination with the key. Execute frequently used system functions when pressed in combination with the key. Executes frequently used system functions when pressed in combination with a function key.

  • Page 15: Touchpad

    TouchPad Item Component TouchPad on/off button TouchPad on/off light Left TouchPad button * TouchPad * TouchPad scroll zone Right TouchPad button * * This table describes factory settings. To view or change pointing device preferences, select Settings > System tab > Mouse.

  • Page 16: Front Components

    Front components Item Component Power light Power switch Drive light Battery light Wireless light Wireless switch Chapter 2 External component identification Function ● On: The device is on. ● Blinking: The device is in Standby. ● Off: The device is off. ●...

  • Page 17: Right-side Components

    Right-side components Item Component Vent SD Card Reader USB port HP Mini Mobile Drive Bay (on models equipped with a solid-state drive) Security lanyard connector Function Enables airflow to cool internal components NOTE: The device fan starts up automatically to cool internal components and prevent overheating.

  • Page 18: Left-side Components

    Left-side components Item Component Power connector Power connector light USB port Vent Expansion port Audio-out (headphone) jack/Audio-in (microphone) jack RJ-45 (network) jack Chapter 2 External component identification Function Connects an AC adapter. ● On: The device is running on AC power. ●...

  • Page 19: Bottom Components

    Bottom components Item Component Battery bay Battery release latches (2) Memory module compartment Vent Function Holds the battery. Release the battery from the battery bay. Contains the memory module slot. NOTE: The release latch for the memory module compartment cover (not illustrated) is located underneath the right battery release latch (see Memory module on page...

  • Page 20: Illustrated Parts Catalog Serial Number Location

    Illustrated parts catalog Serial number location The service tag, affixed to the bottom of the device, provides information that may be needed when troubleshooting system problems. The service tag provides the following information: (1) Product name: This is the product name affixed to the front of the device. (2) Serial number (s/n): This is an alphanumeric identifier that is unique to each product.

  • Page 21: Device Major Components

    Device major components Item Description Display assembly (includes 1 webcam, 1 microphone, 1 speaker box, and 2 WLAN antenna transceivers/cables) 8.9-inch WSVGA BrightView 10.1-inch standard-definition AntiGlare 10.1-inch standard-definition AntiGlare (red-colored models) 10.2-inch WSVGA AntiGlare 10.2-inch WSVGA AntiGlare (red-colored models) Display assembly components on page 16 for more spare part information.

  • Page 22

    Item Description Keyboard NOTE: For a comprehensive list of keyboard spare part numbers, see the on page For use with standard device models For use with red-colored models only Top cover (includes TouchPad) Mass storage devices (4a) Hard drive (select models only; includes cable and bracket): 60-GB, 4200-rpm Hard Drive Hardware Kit (not illustrated) (4b) Solid-state drive (includes cable and bracket)

  • Page 23

    Item Description For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cameroon, Cape Verde, the Central African Republic, Chad, Chile, the People's Republic of China, Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East Timor,...

  • Page 24: Display Assembly Components

    Display assembly components NOTE: 10.1-inch display assembly components are not sold separately. The complete display assembly is available as spare part number 509696-001 for the red-colored model or 507312-001 for all other models. NOTE: 10.2-inch display assembly components are not sold separately. The complete display assembly is available as spare part number 512140-001 for the red-colored model, or 507310-001 for all other models.

  • Page 25

    Item Description (5a) Left and right display panel brackets (5b) Left and right display hinges For use with all 8.9-inch panels Display panel 8.9-inch WSVGA BrightView Display Cable Kit for use with all 8.9-inch panels (includes microphone assembly and display/webcam cable) Includes WLAN Display enclosure (includes logo) For use with all 8.9-inch panels...

  • Page 26: Plastics Kit

    Plastics Kit Item Description Plastics Kit: Memory module compartment cover HP Mini Mobile Drive Bay cover Security lanyard connector SD Card Reader slot bezel Chapter 3 Illustrated parts catalog Spare part number 507317-001...

  • Page 27: Miscellaneous Parts

    Internal display switch module ● Power cable ● SIM card cable ● USB board cable HP Mini Mobile Drive (supported on models equipped with a solid-state drive and HP Mini Mobile Drive Bay) 2-GB 4-GB 8-GB Power cord For use in Argentina...

  • Page 28

    ● Phillips PM2.0×4.5 screw ● Phillips PM2.5×5.0 screw ● Phillips PM2.5×7.0 screw HP Mini Sleeve For standard models For red-colored models VGA cable 30-W UMA AC adapter For use in all countries and regions except Germany For use in Germany only...

  • Page 29: Sequential Part Number Listing

    Sequential part number listing Spare part Description number 490371-001 Power cord for use in North America 490371-011 Power cord for use in Australia 490371-021 Power cord for use in Europe 490371-031 Power cord for use in Singapore and the United Kingdom 490371-061 Power cord for use in Italy 490371-081...

  • Page 30

    Spare part Description number 504595-001 Display enclosure (includes logo) for use with 8.9-inch panels 504596-001 Display Hinge Kit for use with all 8.9-inch panels (includes left/right display hinges and display panel brackets) 504597-001 Display Cable Kit with WLAN for use with all 8.9-inch panels (includes microphone assembly and display/ webcam cable) 504599-001 512-MB memory module (PC2-4200, 533-MHz, DDR2)

  • Page 31

    Display Rubber Kit for use with all 8.9-inch panels 509700-001 Display Screw Kit for use with all 8.9-inch panels 511844-001 HP Mini Sleeve for red-colored models 512140-001 10.2-inch, WSVGA, AntiGlare display assembly for red-colored models (includes 1 webcam, 1 microphone, 1 speaker box, and 2 WLAN antenna transceivers/cables)

  • Page 32

    512315-001 VGA cable 512321-001 HP Mini Sleeve 512329-001 HP Mini Mobile Drive, 2-GB 512330-001 HP Mini Mobile Drive, 4-GB 512331-001 HP Mini Mobile Drive, 8-GB 512851-001 3-cell, 26-Wh Li-Pol battery for red-colored models (for use in all countries and regions except Germany)

  • Page 33: Removal And Replacement Procedures Preliminary Replacement Requirements, Tools Required, Service Considerations, Plastic Parts

    Removal and replacement procedures Preliminary replacement requirements Tools required You will need the following tools to complete the removal and replacement procedures: ● Flat-bladed screwdriver ● Magnetic screwdriver ● Phillips P0 and P000 screwdrivers Service considerations The following sections include some of the considerations that you must keep in mind during disassembly and assembly procedures.

  • Page 34: Drive Handling

    Drive handling CAUTION: Drives are fragile components that must be handled with care. To prevent damage to the device, damage to a drive, or loss of information, observe these precautions: Before removing or inserting a hard drive, shut down the device. If you are unsure whether the device is off or in Hibernation, turn the device on, and then shut it down through the operating system.

  • Page 35: Grounding Guidelines, Electrostatic Discharge Damage

    Grounding guidelines Electrostatic discharge damage Electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure determine the degree of sensitivity. Networks built into many integrated circuits provide some protection, but in many cases, ESD contains enough power to alter device parameters or melt silicon junctions. A discharge of static electricity from a finger or other conductor can destroy static-sensitive devices or microcircuitry.

  • Page 36: Packaging And Transporting Guidelines, Workstation Guidelines

    Packaging and transporting guidelines Follow these grounding guidelines when packaging and transporting equipment: ● To avoid hand contact, transport products in static-safe tubes, bags, or boxes. ● Protect ESD-sensitive parts and assemblies with conductive or approved containers or packaging. ● Keep ESD-sensitive parts in their containers until the parts arrive at static-free workstations.

  • Page 37: Equipment Guidelines

    Equipment guidelines Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation. ● When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps with a minimum of one megohm ±10% resistance in the ground cords. To provide proper ground, wear a strap snugly against the skin at all times.

  • Page 38: Component Replacement Procedures, Service Tag

    Component replacement procedures This chapter provides removal and replacement procedures. There are as many as 49 screws, in 7 different sizes, that must be removed, replaced, or loosened when servicing the device. Make special note of each screw size and location during removal and replacement. Service tag The service tag, affixed to the bottom of the device, provides information that may be needed when troubleshooting system problems.

  • Page 39: Device Feet

    Device feet The device feet are adhesive-backed rubber pads. The feet are included in the Rubber Kit, spare part number 504613-001. There are 4 rubber feet that are installed on the base enclosure in the locations illustrated below. Component replacement procedures...

  • Page 40: Battery

    Battery Description 3-cell, 26-Wh Li-Pol battery 3-cell, 26-Wh Li-Pol battery for red-colored models (for use in all countries and regions except Germany) 3-cell, 26-Wh Li-Pol battery for red-colored models (for use in Germany only) Before disassembling the device, follow these steps: Shut down the device.

  • Page 41: Memory Module

    Memory module Description 512-MB (PC2-4200, 533-MHz, DDR2) 1024-MB (PC2-4200, 533-MHz, DDR2) 2048-MB (PC2-4200, 533-MHz, DDR2) Before removing the memory module, follow these steps: Shut down the device. If you are unsure whether the device is off or in Hibernation, turn the device on, and then shut it down through the operating system.

  • Page 42

    Remove the memory module (2) by pulling the module away from the slot at an angle. NOTE: Memory modules are designed with a notch (3) to prevent incorrect insertion into the memory module slot. Reverse this procedure to install a memory module. Chapter 4 Removal and replacement procedures...

  • Page 43: Keyboard

    Keyboard NOTE: For a comprehensive list of spare part numbers, see the on page Description For use with standard device models Before removing the keyboard, follow these steps: Shut down the device. If you are unsure whether the device is off or in Hibernation, turn the device on, and then shut it down through the operating system.

  • Page 44

    Grasp the tabs on the outer edges of the keyboard (1), lift the rear edge of the keyboard (2) until it rests at an angle, and then slide it back (3) until it rests on the display assembly. Release the zero insertion force (ZIF) connector (1) to which the keyboard cable is attached, and then disconnect the cable (2) from the system board.

  • Page 45: Mass Storage Devices

    Mass storage devices NOTE: Each hard drive spare part kit and solid-state drive spare part kit includes a cable and bracket. Description 8-GB solid-state drive 16-GB solid-state drive 60-GB, 4200-rpm hard drive Before removing the hard drive or solid-state drive, follow these steps: Shut down the device.

  • Page 46

    Remove the two Phillips PM2.0×4.5 screws (3) that secure the hard drive to the device. Then lift the drive (4) up, and slide it out of the drive bay. Reverse this procedure to install the hard drive. To remove the solid-state drive: Release the ZIF connector (1) to which the USB board pass-through cable (that lies across the top of the drive) is attached.

  • Page 47

    Remove the two Phillips PM2.0×4.5 screws (3) that secure the drive bracket to the device, and then remove the bracket (4) from the drive bay. Remove the three Phillips PM2.0×3.0 screws (1) that secure the solid-state drive to the bracket, and then remove the drive from the bracket (2).

  • Page 48: Top Cover

    Top cover Description Top cover (includes TouchPad) Before removing the top cover, follow these steps: Shut down the device. If you are unsure whether the device is off or in Hibernation, turn the device on, and then shut it down through the operating system. Disconnect all external devices connected to the device.

  • Page 49

    Turn the device right-side up, with the front toward you. Open the device as far as possible. Remove the Phillips PM2.0×4.5 screw (1) and the Phillips PM2.5×5.0 screw (2) that secure the top cover to the base enclosure. Lift the rear edge of the top cover (1), swing it up, and then slide it back slightly to rest against the display assembly (2) at an angle.

  • Page 50

    Release the ZIF connector (1) to which the TouchPad button board cable is connected, and then disconnect the cable (2) from the system board. Remove the top cover. Reverse this procedure to install the top cover. Chapter 4 Removal and replacement procedures...

  • Page 51: Wlan Module

    WLAN module Description Broadcom 4312 802.11/b/g WLAN modules: For use in Canada, the Cayman Islands, Guam, Puerto Rico, the U.S. Virgin Islands, and the United States For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cameroon, Cape Verde, the Central African Republic, Chad, Chile, the People's Republic of China, Colombia, Comoros,...

  • Page 52

    Remove the WLAN module: Disconnect the wireless antenna cables (1) from the terminals on the WLAN module. Remove the Phillips PM2.0×3.0 screw (2) that secures the WLAN module to the system board. (The edge of the module opposite the slot rises away from the device.) Remove the WLAN module (3) by pulling the module away from the slot at an angle.

  • Page 53: Rtc Battery

    RTC battery Description RTC battery Before removing the real-time clock (RTC) battery, follow these steps: Shut down the device. If you are unsure whether the device is off or in Hibernation, turn the device on, and then shut it down through the operating system. Disconnect all external devices connected to the device.

  • Page 54: Bluetooth Module

    Bluetooth module NOTE: The Bluetooth module spare part kit does not include a Bluetooth module cable. The Bluetooth module cable is included in the Cable Kit, spare part number 507708-001. Description Bluetooth module Before removing the Bluetooth module, follow these steps: Shut down the device.

  • Page 55: System Board

    System board NOTE: The system board spare part kit includes a processor and replacement thermal material. Description System board equipped with 1.6-GHz processor Before removing the system board, follow these steps: Shut down the device. If you are unsure whether the device is off or in Hibernation, turn the device on, and then shut it down through the operating system.

  • Page 56

    Disconnect the following cables from the system board: (1) Speaker cables (2) Microphone cable (3) Fan cable (4) Power cable (5) Display panel cable NOTE: The USB board pass-through cable was disconnected earlier (see devices on page Remove the two Phillips PM1.6×2.5 screws (1) that secure the actuators for the power switch and wireless on/off switch to the system board, and then remove the actuators (2).

  • Page 57

    Remove the two Phillips PM2.0×3.0 screws (1) that secure the USB connector bracket to the base enclosure, and then remove the bracket (2). NOTE: The USB connector bracket is included in the Bracket Kit, spare part number 507318-001. Remove the Phillips PM2.0×4.5 screw that secures the system board to the base enclosure. Component replacement procedures...

  • Page 58

    Grasp the system board at its midpoint (1), lift the right side up (2), and remove the system board (3). Reverse the procedure to install the system board. Chapter 4 Removal and replacement procedures...

  • Page 59: Heat Sink Assembly

    Heat sink assembly NOTE: The heat sink assembly spare part kit includes replacement thermal material. Description Heat sink assembly Before removing the heat sink assembly, follow these steps: Shut down the device. If you are unsure whether the device is off or in Hibernation, turn the device on, and then shut it down through the operating system.

  • Page 60

    Remove the heat sink assembly (2). NOTE: Due to the adhesive quality of the thermal material located between the heat sink assembly and system board components, it may be necessary to move the heat sink assembly from side to side to detach the assembly. NOTE: The thermal material must be thoroughly cleaned from the surfaces of the heat sink assembly and the system board each time the heat sink assembly is removed.

  • Page 61

    NOTE: The fan spare part kit does not include a fan cable. The fan cable is included in the Cable Kit, spare part number 507708-001. Description NOTE: To properly ventilate the device, allow at least a 7.6-cm (3-inch) clearance on the left side of the device.

  • Page 62

    Remove the fan: Detach the black Mylar covering from the fan. Detach the black tape from the fan cables, and then move the cables aside. Remove the Phillips PM2.0×4.5 screw (1) and the Phillips PM2.0×3.0 screw (2) that secure the fan to the base enclosure.

  • Page 63

    Remove the fan (3). Reverse this procedure to install the fan. NOTE: To properly ventilate the device, allow at least a 7.6-cm (3-inch) clearance on the left side of the device. The device uses an electric fan for ventilation. The fan is controlled by a temperature sensor and is designed to turn on automatically when high temperature conditions exist.

  • Page 64: Usb Board And Internal Display Switch

    USB board and internal display switch NOTE: The internal display switch module is included in the Cable Kit, spare part number 507708-001. Description USB board Before removing the USB board, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.

  • Page 65

    Remove the DC jack bracket (2) and the USB board (3) from the base enclosure. If it is necessary to replace the internal display switch module, perform the following steps: Remove the Phillips PM2.0×3.0 screw (1) that secures the internal display switch bracket to the base enclosure.

  • Page 66: Display Assembly

    Display assembly NOTE: Each display assembly spare part kit includes 1 webcam, 1 microphone, 1 speaker box, and 2 WLAN antenna transceivers/cables. NOTE: 10.1-inch display assembly components are not sold separately. The complete display assembly is available as spare part number 509696-001 for the red-colored model or 507312-001 for all other models.

  • Page 67

    CAUTION: Support the display assembly when removing the following screws. Failure to support the display assembly can result in damage to the display assembly and other device components. Remove the three remaining Phillips PM2.5×5.0 screws (1) that secure the display assembly to the device, and then remove the display assembly (2).

  • Page 68

    Remove the speaker assembly (2). The speaker assembly is available using spare part number 506335-001. If it is necessary to replace the display hinges, remove the two Phillips PM2.0×4.5 screws (1) that secure each hinge to the display enclosure, and then remove the hinges (2). The hinges are available in the Display Hinge Kit, spare part number 504596-001 for all 8.9-inch panels.

  • Page 69

    If it is necessary to replace the display bezel, flex the inside edges of the bottom (1), left and right sides (2), and the top (3) of the display bezel until the bezel disengages from the display enclosure, and then remove the display bezel (4). The spare part number for the 8.9-inch display bezels is 506333-001.

  • Page 70

    Remove the two Phillips PM2.0×3.0 screws (1) that secure the webcam module to the display enclosure, and then remove the webcam module (2). The webcam module is available using spare part number 504594-001 for all 8.9-inch panels. If it is necessary to replace the display panel, perform the following steps: Remove the nine Phillips PM2.0×3.0 screws that secure the display panel to the display enclosure.

  • Page 71

    Remove the display panel from the display enclosure (3). An 8.9-inch display panel is available using spare part number 509698-001. If it is necessary to replace the display panel brackets, remove the four Phillips PM2.0×3.0 screws (1) that secure the brackets to the display panel, and then remove the brackets (2). The brackets are available in the Display Hinge Kit, spare part number 504596-001 for all 8.9-inch panels.

  • Page 72

    If it is necessary to replace the wireless antenna transceivers and cables, detach the cables from the adhesive that secures them to the display enclosure, and then remove the cables. The wireless antenna transceivers and cables for all 8.9-inch panels are available in the Display Cable Kit, spare part number 504597-001 (with WLAN).

  • Page 73: Starting The Setup Utility, Using The Setup Utility, Changing The Language Of The Setup Utility

    Setup Utility Starting the Setup Utility The Setup Utility is a ROM-based information and customization utility that can be used even when your operating system is not working. The utility reports information about the device and provides settings for startup, security, and other preferences.

  • Page 74: Navigating And Selecting In The Setup Utility, Displaying System Information

    Navigating and selecting in the Setup Utility Because the Setup Utility is not operating system based, it does not support the TouchPad. Navigation and selection are by keystroke. ● To choose a menu or a menu item, use the arrow keys. ●...

  • Page 75: Exiting The Setup Utility, Setup Utility Menus, Main Menu, Security Menu

    Exiting the Setup Utility You can exit the Setup Utility with or without saving changes. ● To exit the Setup Utility and save your changes from the current session: If the Setup Utility menus are not visible, press keys to select Exit > Exit Saving Changes, and then press enter. ●...

  • Page 76: System Configuration Menu, Diagnostics Menu

    System Configuration menu Select Language Support Processor C4 State Boot Options Diagnostics menu Select Hard Disk Self Test (select models only) Memory Test Chapter 5 Setup Utility To do this Change the Setup Utility language. Enable/disable the processor C4 sleep state. Set the following boot options: ●...

  • Page 77: Device Specifications

    Specifications Device specifications Dimensions Depth Width Height Weight 10.2-in. LCD, equipped with a 3-cell battery, 60-GB hard drive, 1-GB memory, WLAN module, and 2 wireless antennae 10.2-in. LCD, equipped with a 3-cell battery, 8-GB solid-state drive, 1-GB memory, WLAN module, and 2 wireless antennae 8.9-in.

  • Page 78: Inch, Wsvga, Brightview Display Specifications

    8.9-inch, WSVGA, BrightView display specifications Dimensions Height Width Diagonal Number of colors Contrast ratio Brightness Pixel resolution Pitch Format Configuration Backlight Character display Total power consumption Viewing angle Chapter 6 Specifications Metric U.S. 11.34 cm 4.47 in 19.51 cm 7.68 in 22.61 cm 8.90 in 262,144...

  • Page 79: Inch, Standard-definition, Antiglare Display Specifications

    10.1-inch, standard-definition, AntiGlare display specifications Dimensions Height Width Diagonal Number of colors Contrast ratio Brightness Pixel resolution Pitch Format Configuration Backlight Character display Total power consumption Viewing angle Metric 23.45 cm 14.30 cm 25.55 cm 262,144 400:1 (typical) 200 nits (typical) 0.2175 ×...

  • Page 80: Inch, Wsvga, Antiglare Display Specifications

    10.2-inch, WSVGA, AntiGlare display specifications Dimensions Height Width Diagonal Number of colors Contrast ratio Brightness Pixel resolution Pitch Format Configuration Backlight Character display Total power consumption Viewing angle Chapter 6 Specifications Metric U.S. 12.53 cm 4.93 in 22.27 cm 8.77 in 25.55 cm 10.06 in 262,144...

  • Page 81: Hard Drive Specifications

    Hard drive specifications Dimensions Height Width Weight Interface type Transfer rate Security Seek times (typical read, including setting) Single track Average Maximum Logical blocks Disc rotational speed Operating temperature * 1 GB = 1 billion bytes when referring to hard drive storage capacity. Actual accessible capacity is less. Actual drive specifications may differ slightly.

  • Page 82: Solid-state Drive Specifications

    Solid-state drive specifications Performance Transfer modes supported Sustained read Sustained write Characteristics Interface MLC NAND flash capacity Electrical specifications DC supply voltage Standby current Active current Environmental specifications Operating temperature Storage temperature Operating altitude Humidity Shock Acoustic noise Vibration Physical specifications Connector Weight (8-GB model) Weight (16-GB model)

  • Page 83: System Dma Specifications, System Interrupt Specifications

    System DMA specifications Hardware DMA DMA0 DMA1 * DMA2 * DMA3 DMA4 System interrupt specifications Hardware IRQ IRQ0 IRQ1 IRQ8 IRQ9* IRQ12 IRQ13 IRQ14 IRQ15 IRQ16 IRQ17 IRQ18 IRQ19 IRQ23 * Default configuration System function Not applicable Not applicable Not applicable Not applicable Direct memory access controller System function...

  • Page 84: System I/o Address Specifications

    System I/O address specifications I/O address (hex) 000 - 00F 000 - CF7 010 - 01F 020 - 021 022 - 03F 040 - 043 044 - 05F 060 - 060 061 - 061 062 - 062 063- 063 064 - 064 065 - 065 066 - 066 067 - 06F...

  • Page 85

    I/O address (hex) 279 - 279 3B0 - 3BB 3C0 - 3DF 3F6 - 3F6 400 - 41F 480 - 4BF 4D0 - 4D1 500 - 501 800 - 87F A79 - A79 0D00 - FFFF D480 - D49F D800 - D81F D880 - D89F DC00 - DC1F DC80 - DC87...

  • Page 86: System Memory Map Specifications

    System memory map specifications Memory address 00000000 - 0009FFFF 000A0000 - 000BFFFF 000A0000 - 000BFFFF 000C0000 - 000CFFFF 000D0000 - 000DFFFF 000E0000 - 000FFFFF 00100000 - 3F7FFFFF 3F800000 - DFFFFFFF D0000000 - DFFFFFFF E0000000 - E3FFFFFF E4000000 - FED8FFFF FE880000 - FE8FFFFF FE937C00 - FE937FFF FE938000 - FE93BFFF FE940000 - FE97FFFF...

  • Page 87: Phillips Pm1.6×2.5 Screw

    Screw listing This section provides specification and reference information for the screws and screw locks used in the device. All screws listed in this section are available in the Screw Kit, spare part number 504614-001; or in the Display Screw Kit, spare part number 509700-001 for all 8.9-inch panels or 515211-001 for 10.1-inch panels (Compaq Mini 700 only).

  • Page 88

    Where used: Two screws that secure the heat sink to the system board Chapter 7 Screw listing...

  • Page 89: Phillips Pm1.6×4.0 Screw

    Phillips PM1.6×4.0 screw Color Silver Where used: One screw that secures the keyboard to the device Quantity Length 4.0 mm Thread Head diameter 1.60 mm 3.5 mm Phillips PM1.6×4.0 screw...

  • Page 90: Phillips Pm1.6×6.0 Screw

    Phillips PM1.6×6.0 screw Color Black Where used: One screw that secures the keyboard to the device Chapter 7 Screw listing Quantity Length 6.0 mm Thread Head diameter 1.60 mm 3.5 mm...

  • Page 91: Phillips Pm2.0×3.0 Screw

    Phillips PM2.0×3.0 screw Color Black Where used: Three screws that secure the solid-state drive to its bracket Where used: One screw that secures the WLAN module to the system board Quantity Length 3.0 mm Thread Head diameter 2.0 mm 4.0 mm Phillips PM2.0×3.0 screw...

  • Page 92

    Where used: Two screws that secure the USB connector bracket to the system board Where used: One screw that secures the fan to the base enclosure Where used: One screw that secures the DC jack bracket to the base enclosure Chapter 7 Screw listing...

  • Page 93

    Where used: One screw that secures the internal display switch bracket to the base enclosure Where used: Two screws that secure the webcam module to the display enclosure Where used: Nine screws that secure the display panel to the display enclosure Phillips PM2.0×3.0 screw...

  • Page 94

    Where used: Four screws that secure the left and right display panel brackets to the display panel Chapter 7 Screw listing...

  • Page 95: Phillips Pm2.0×4.5 Screw

    Phillips PM2.0×4.5 screw Color Silver Where used: Two screws that secure the hard drive to the device Where used: Two screws that secure the solid-state drive bracket to the device Quantity Length 4.5 mm Thread Head diameter 2.0 mm 4.0 mm Phillips PM2.0×4.5 screw...

  • Page 96

    Where used: One screw that secures the top cover to the device Where used: One screw that secures the fan and DC jack bracket to the base enclosure Where used: Two screws that secure the speaker assembly to the display enclosure Chapter 7 Screw listing...

  • Page 97

    Where used: Four screws that secure the display hinges to the display assembly Phillips PM2.0×4.5 screw...

  • Page 98: Phillips Pm2.5×5.0 Screw

    Phillips PM2.5×5.0 screw Color Silver Where used: Four screws that secure the display assembly and top cover to the device Chapter 7 Screw listing Quantity Length 5.0 mm Thread Head diameter 2.5 mm 4.5 mm...

  • Page 99: Phillips Pm2.5×7.0 Screw

    Phillips PM2.5×7.0 screw Color Black Where used: Four screws that secure the top cover to the base enclosure Quantity Length 7.0 mm Thread Head diameter 2.5 mm 4.0 mm Phillips PM2.5×7.0 screw...

  • Page 100: Backup And Restore

    Backup and restore To protect your information, back up your files and folders. Then if the system fails, you can restore your important files from copies. You can also use the options listed in this chapter to restore the operating system and programs that were installed at the factory.

  • Page 101: Backing Up Your Information

    Backing up your information Successful recovery after a system failure depends on whether you have completely backed up your files. You should back up your files on a regular basis to maintain up-to-date information. You can back up important personal files and folders to an external hard drive or USB flash drive (both purchased separately).

  • Page 102: Restoring Your Information, Using System Restore

    ● HP MIE Restore Image Creator (USB flash drive): If you are unable to boot (start up) the device, and if you are unable to use System Restore, you can use another computer to download the HP MIE Restore Image Creator utility and create a bootable USB flash drive (purchased separately).

  • Page 103: Using Hp Mie Restore Image Creator

    An additional computer running either a Windows® or Linux operating system To perform this restore option, you download the HP MIE Restore Image Creator utility and HP Mini operating system onto another computer and then transfer the necessary files to the USB flash drive.

  • Page 104: Restoring Using A Windows Computer

    From the Start menu, launch HP MIE Restore Image Creator. Select Download HP Mini MIE recovery image. Select the target USB flash drive, and click Start to download the latest HP Mini recovery image from the HP web site. The recovery image will be downloaded and saved to the Windows computer and then written to the USB flash drive.

  • Page 105

    Restore your personal files. NOTE: After this process is complete, you can uninstall the HP MIE Restore Image Creator utility from the Windows computer and delete the downloaded recovery image from the USB flash drive. (The image must be deleted manually.)

  • Page 106: Restoring Using A Linux Computer

    Select “Download restore image/HP MIE Restore Image. Select the target USB flash drive, and click Start to download the latest HP Mini recovery image from the HP web site. The recovery image will be downloaded and saved to the Linux computer, and then written to the USB flash drive.

  • Page 107

    Restore your personal files. NOTE: After this process is complete, you can uninstall the HP MIE Restore Image Creator utility from the Linux computer and delete the downloaded recovery image from the USB flash drive. (The image must be deleted manually.)

  • Page 108: Connector Pin Assignments Audio-in (microphone), Audio-out (headphone)

    Connector pin assignments Audio-in (microphone) Audio-out (headphone) 100 Chapter 9 Connector pin assignments Signal Audio signal in Audio signal in Ground Signal Audio out, left channel Audio out, right channel Ground...

  • Page 109: Rj-45 (network), Universal Serial Bus

    RJ-45 (network) Universal Serial Bus Signal Transmit + Transmit - Receive + Unused Unused Receive - Unused Unused Signal +5 VDC Data - Data + Ground RJ-45 (network) 101...

  • Page 110: Power Cord Set Requirements, Requirements For All Countries And Regions

    10 Power cord set requirements The wide range input feature of the device permits it to operate from any line voltage from 100 to 120 volts AC or from 220 to 240 volts AC. The 3-conductor power cord set included with the device meets the requirements for use in the country or region where the equipment is purchased.

  • Page 111: Requirements For Specific Countries And Regions

    Requirements for specific countries and regions Country/region Australia Austria Belgium Canada Denmark Finland France Germany Italy Japan The Netherlands Norway The People's Republic of China South Korea Sweden Switzerland Taiwan The United Kingdom The United States The flexible cord must be Type HO5VV-F, 3-conductor, 1.0-mm² conductor size. Power cord set fittings (appliance coupler and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used.

  • Page 112: Recycling Battery, Display

    When you remove these components, handle them carefully. NOTE: Materials Disposal. This HP product contains mercury in the backlight in the display assembly that might require special handling at end-of-life. Disposal of mercury may be regulated because of environmental considerations. For disposal or recycling information, contact your local authorities, or see the Electronic Industries Alliance (EIA) Web site at http://www.eiae.org.

  • Page 113

    Perform the following steps to disassemble the display assembly: Remove all screw covers (1) and screws (2) that secure the display bezel to the display assembly. Lift up and out on the left and right inside edges (1) and the top and bottom inside edges (2) of the display bezel until the bezel disengages from the display assembly.

  • Page 114

    Disconnect all display panel cables (1) from the display inverter and remove the inverter (2). Remove all screws (1) that secure the display panel assembly to the display enclosure. Remove the display panel assembly (2) from the display enclosure. Turn the display panel assembly upside down. Remove all screws that secure the display panel frame to the display panel.

  • Page 115

    Remove the display panel frame (2) from the display panel. Remove the screws (1) that secure the backlight cover to the display panel. Lift the top edge of the backlight cover (2) and swing it outward. Remove the backlight cover. Turn the display panel right-side up.

  • Page 116

    Remove the backlight cables (1) from the clip (2) in the display panel. Turn the display panel upside down. WARNING! The backlight contains mercury. Exercise caution when removing and handling the backlight to avoid damaging this component and causing exposure to the mercury. Remove the backlight frame from the display panel.

  • Page 117

    Remove the backlight from the backlight frame. Disconnect the display panel cable (1) from the LCD panel. Remove the screws (2) that secure the LCD panel to the display rear panel. Release the LCD panel (3) from the display rear panel. Release the tape (4) that secures the LCD panel to the display rear panel.

  • Page 118: Index

    Index AC adapter, spare part number 20, 21 antenna locations 5 removal 64 spare part number 17, 64 audio, product description 2 audio-in jack location 10 pin assignments 100 audio-out jack location 10 pin assignments 100 base enclosure, spare part number 15, 22, 23 battery location 11...

  • Page 119

    10 pin assignments 100 heat sink assembly removal 51 spare part number 51 HP Mini Mobile Drive, spare part number 19 HP Mobile Drive, location 9 I/O address specifications 76 in Setup Utility 65 internal display switch 4...

  • Page 120

    hard drive 1 internal media cards 2 keyboard 2 mass storage device 1 memory module 1 modem 2 operating system 3 optical drive 1 panels 1 pointing device 2 ports 2 power requirements 2 processors 1 product name 1 security 3 serviceability 3 solid-state drive 1 webcam 2...

  • Page 121

    wireless switch 8 WLAN module removal 43 spare part number 14, 21, workstation guidelines 28 Index 113...

Comments to this Manuals

Symbols: 0
Latest comments: