Honda ST1300 2006 Setup Instructions
  1. Manuals
  2. Brands
  3. Honda Manuals
  4. Motorcycle
  5. ST1300 2006
  6. Setup instructions

Honda ST1300 2006 Setup Instructions

Hide thumbs
Table of Contents

Advertisement

Quick Links

Set-up and pre-delivery service
must be performed by an authorized
Honda motorcycle dealer.
©2006 American Honda Motor Co., Inc. - All Rights Reserved
2006 ST1300/A
SET-UP
INSTRUCTIONS
MPD 11396 (0601)
Issued: January 2006

Advertisement

Table of Contents
loading

Related Manuals for Honda ST1300 2006

Summary of Contents for Honda ST1300 2006

  • Page 1 2006 ST1300/A SET-UP INSTRUCTIONS Set-up and pre-delivery service must be performed by an authorized Honda motorcycle dealer. MPD 11396 (0601) Issued: January 2006 ©2006 American Honda Motor Co., Inc. - All Rights Reserved...

  • Page 2: For Your Customer's Safety

    To reduce the possibility of a fire or explosion, be careful when working around gasoline or batteries. Use only a nonflammable solvent, not gasoline, to clean parts. Keep all cigarettes, sparks and flames away from the battery and all fuel-related parts. ©2006 American Honda Motor Co., Inc. - All Rights Reserved...

  • Page 3: Modifications And Accessories

    Indicates the pre-delivery section Modifications and Accessories Modifications that you may have made, or should make in the future, to any Honda product, shall be deemed by our company to have been performed at your sole risk and responsibility, and without our company's or the manufacturer's approval, or consent, implied or expressed.
  • Page 4 (Reorder No. S0477) before proceeding. 3. Remove the side braces, wheel, loose parts cartons, and crate frame. Remove the ties securing the front wheel and loose parts cartons. PARTS PARTS TIES CARTON CARTON ©2006 American Honda Motor Co., Inc. - All Rights Reserved...
  • Page 5 Using two people, carefully remove the PLATE crate frame, being careful not to damage the motorcycle. Remove the front shipping brace, being careful not to damage the motorcycle. FRONT SHIPPING BRACE ©2006 American Honda Motor Co., Inc. - All Rights Reserved...
  • Page 6 (Continued on next page.) * Optional parts. Hand the knee pads to the customer at the time of delivery or install if the customer wants them installed (see step 15). ©2006 American Honda Motor Co., Inc. - All Rights Reserved...
  • Page 7 Claims for missing loose parts or those damaged during transit should be submitted to American Honda, not the carrier. After completing repairs, submit a Transportation Claim via iN. For complete details, please refer to the Warranty Policy and Procedures Manual.
  • Page 8 Remove the washer bolts, and lower shipping bracket from the crate base. Discard the washer bolts. CALIPER BOLTS CALIPER BOLTS LOWER WASHER BOLTS SHIPPING (discard) BRACKET PINCH BOLTS AXLE BOLT ©2006 American Honda Motor Co., Inc. - All Rights Reserved...
  • Page 9 6 x 16 mm flange bolts. 6 x 18 mm SOCKET BOLT Torque the bolts. RUBBER WASHER Torque: 12 N·m (1.2 kgf·m, 9 lbf·ft) 6 x 20 mm FLANGE BOLT REFLECTOR 6 mm NUT ©2006 American Honda Motor Co., Inc. - All Rights Reserved...

  • Page 10: Install The Front Wheel

    SHAFT Torque: 79 N·m (8.1 kgf·m, 58 lbf·ft) Tighten the right axle pinch bolts to the 16.5 mm LEFT SIDE specified torque. COLLAR Torque: 22 N·m (2.2 kgf·m, 16 lbf·ft) ©2006 American Honda Motor Co., Inc. - All Rights Reserved...
  • Page 11 Visually check the position of the brake disc in relation to the brake caliper; it should be DISC centered. If not, recheck the wheel and brake caliper installation. CALIPER BRACKET ©2006 American Honda Motor Co., Inc. - All Rights Reserved...

  • Page 12: Install The Mirrors

    6 x 20 mm flange bolts on each side. Torque the bolts. Torque: 12 N·m (1.2 kgf·m, 9 lbf·ft) Install the two hose clips as shown. SHIPPING BOLTS (discard) ©2006 American Honda Motor Co., Inc. - All Rights Reserved...
  • Page 13 STRAP MIRROR COVER Carefully install the mirror covers by pressing the cover prongs into the grommets on the MIRROR COVER bracket, and mirror bracket ends into the cover as shown. ©2006 American Honda Motor Co., Inc. - All Rights Reserved...

  • Page 14: Install The Windscreen

    Torque: 12 N·m (1.2 kgf·m, 9 lbf·ft) Then, install the following: Windscreen covers • 4 x 25 mm pan screws • Torque the pan screws. Torque: 1.0 N·m (0.1 kgf·m, 0.7 lbf·ft) ©2006 American Honda Motor Co., Inc. - All Rights Reserved...
  • Page 15 Push in on the saddlebag lever lock while aligning it with the cutout in the saddlebag as shown. SADDLEBAG LEVER LOCK CUTOUT ©2006 American Honda Motor Co., Inc. - All Rights Reserved...
  • Page 16 Close the latch lever and turn the ignition key counterclockwise. IGNITION Be sure the seat is locked securely in position. Place the ignition key into the ignition. ©2006 American Honda Motor Co., Inc. - All Rights Reserved...

  • Page 17: Install Engine Guard Covers

    After attaching the pads, press down firmly over the entire area of the pad to ensure maximum adhesion. Avoid washing the motorcycle or riding in wet conditions for 24 hours after attaching the pads. ©2006 American Honda Motor Co., Inc. - All Rights Reserved...
  • Page 18 NEGATIVE (-) BATTERY TERMINAL POSITIVE (+) BATTERY TERMINAL BATTERY BOX RIGHT TURN SIGNAL 2P (SKY BLUE) CONNECTOR RIGHT RUNNING LEFT TURN LIGHT SIGNAL 2P CONNECTOR (ORANGE) CONNECTOR LEFT RUNNING LIGHT CONNECTOR ©2006 American Honda Motor Co., Inc. - All Rights Reserved...

  • Page 19: Service/Install Battery

    Close the latch lever. SADDLEBAG Remove the right side cover: 5 mm SCREWS Remove the screws and the right side cover. SIDE COVER 5 mm SCREW ©2006 American Honda Motor Co., Inc. - All Rights Reserved...
  • Page 20 (+) cable to contact any metal parts. Verify the correct battery cable routing by referring to step 16. Reinstall the battery holder, bolts, battery cover, and side cover in the reverse order of removal. ©2006 American Honda Motor Co., Inc. - All Rights Reserved...
  • Page 21 Close the latch lever and lock it with the ignition key. Remove the ignition key and place it in the ignition switch in the OFF position. SADDLEBAG SLOTS ©2006 American Honda Motor Co., Inc. - All Rights Reserved...

  • Page 22: Verify Throttle Freeplay

    INSPECTION WINDOW Check that the oil level is between the upper and lower level marks in the UPPER LEVEL MARK inspection window. LOWER LEVEL MARK ©2006 American Honda Motor Co., Inc. - All Rights Reserved...

  • Page 23: Check Final Drive Oil Level

    Recommended oil: Pro Honda Shaft Drive Oil or equivalent SAE 80 hypoid gear oil Reinstall and torque the oil filler cap. LOWER EDGE Torque: 12 N·m (1.2 kgf·m, 9 lbf·ft) ©2006 American Honda Motor Co., Inc. - All Rights Reserved...

  • Page 24: Front/Rear Brake Reservoir Fluid Levels

    Idle speed: l,000 100 rpm If an adjustment is needed, turn the throttle stop screw to set the idle speed INCREASE using a screwdriver. Stop the engine and remove the tachometer. ©2006 American Honda Motor Co., Inc. - All Rights Reserved...
  • Page 25 Turn on the ignition, set the engine stop switch to the RUN position, and press the starter button. If the engine starts, there is a problem with the sidestand ignition cut-off switch. Troubleshoot the cause. ©2006 American Honda Motor Co., Inc. - All Rights Reserved...

  • Page 26: Adjust Front Seat Height

    LOW POSITION 27. Complete the Set-up/Pre-delivery form. Complete an On-Road Motorcycle Set-up/Pre- delivery Checklist (Reorder No. S0299, also available on iN) by checking the boxes confirming the steps were done. ©2006 American Honda Motor Co., Inc. - All Rights Reserved...
  • Page 27 2006 ST1300/A ©2006 American Honda Motor Co., Inc. - All Rights Reserved...
  • Page 28 ©2006 American Honda Motor Co., Inc. - All Rights Reserved...

This manual is also suitable for:

2006 st1300/a

Table of Contents