California Energy Commission Battery Charging Testing Instructions - VTech IS7101 User Manual

Dect 6.0 accessory handset for use with vtech models is7121/is7121-2/is7121-22
Table of Contents

Advertisement

Changes or modifications to this equipment not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
This device complies with Part 5 of the FCC rules. Operation is subject to the following two
conditions: () this device may not cause harmful interference, and () this device must accept
any interference received, including interference that may cause undesired operation. Privacy of
communications may not be ensured when using this telephone.
To ensure safety of users, the FCC has established criteria for the amount of radio frequency
energy that can be safely absorbed by a user or bystander according to the intended usage of the
product. This product has been tested and found to comply with the FCC criteria. The handset may
be safely held against the ear of the user. The telephone base and the door bell shall be installed
and used such that parts of the user's body other than the hands are maintained at a distance of
approximately 0 cm (8 inches) or more.
This Class B digital apparatus complies with Canadian requirement:
CAN ICES-3 (B)/NMB-3(B).
FCC Part 68 and ACTA
This equipment complies with Part 68 of the FCC rules and with technical requirements adopted by
the Administrative Council for Terminal Attachments (ACTA). The label on the back or bottom of this
equipment contains, among other things, a product identifier in the format US:AAAEQ##TXXXX.
This identifier must be provided to your telephone service provider upon request.
The plug and jack used to connect this equipment to premises wiring and the telephone network
must comply with applicable Part 68 rules and technical requirements adopted by ACTA. A
compliant telephone cord and modular plug is provided with this product. It is designed to be
connected to a compatible modular jack that is also compliant. An RJ jack should normally be
used for connecting to a single line and an RJ jack for two lines. See the installation instructions
in the user's manual.
The Ringer Equivalence Number (REN) is used to determine how many devices you may connect
to your telephone line and still have them ring when you are called. The REN for this product is
encoded as the 6th and th characters following the US: in the product identifier (e.g., if ## is 03,
the REN is 0.3). In most, but not all areas, the sum of all RENs should be five (5.0) or less. For
more information, please contact your telephone service provider.
This equipment may not be used with Party Lines. If you have specially wired alarm dialing
equipment connected to your telephone line, ensure the connection of this equipment does not
disable your alarm equipment. If you have questions about what will disable alarm equipment,
consult your telephone service provider or a qualified installer.
If this equipment is malfunctioning, it must be unplugged from the modular jack until the problem
has been corrected. Repairs to this telephone equipment can only be made by the manufacturer
or its authorized agents. For repair procedures, follow the instructions outlined under the Limited
warranty.
If this equipment is causing harm to the telephone network, the telephone service provider may
temporarily discontinue your telephone service. The telephone service provider is required to
notify you before interrupting service. If advance notice is not practical, you will be notified as soon
as possible. You will be given the opportunity to correct the problem and the telephone service
provider is required to inform you of your right to file a complaint with the FCC. Your telephone
service provider may make changes in its facilities, equipment, operation, or procedures that could
affect the proper functioning of this product. The telephone service provider is required to notify you
if such changes are planned.
If this product is equipped with a corded or cordless handset, it is hearing aid compatible.
If this product has memory dialing locations, you may choose to store emergency telephone numbers
(e.g., police, fire, medical) in these locations. If you do store or test emergency numbers, please:
Remain on the line and briefly explain the reason for the call before hanging up.
Perform such activities in off-peak hours, such as early morning or late evening.
Industry Canada
Operation is subject to the following two conditions: () this device may not cause harmful
interference, and () this device must accept any interference received, including interference that
may cause undesired operation.
Privacy of communications may not be ensured when using this phone.
The term ''IC:'' before the certification/registration number only signifies that the Industry Canada
technical specifications were met.
The Ringer Equivalence Number (REN) for this terminal equipment is .0. The REN is an
indication of the maximum number of devices allowed to be connected to a telephone interface.
The termination on an interface may consist of any combination of devices subject only to the
requirement that the sum of the RENs of all the devices does not exceed five.

California Energy Commission battery charging testing instructions

This telephone is set up to comply with the energy-conserving standards right out of the box. These
instructions are intended for California Energy Commission (CEC) compliance testing only.
When the CEC battery charging testing mode is activated, all telephone functions, except battery
charging, will be disabled.
When first purchased and properly installed for charging (see Battery Installation on page ), put
the handset on the charger to charge. The CEC battery charging testing mode is activated while
charging.
If you have registered the handset to a doorbell base, below are the testing instructions.
To activate the CEC battery charging testing mode:
. Unplug the telephone base power adapter from the power outlet. Make sure all handsets are plugged with
charged batteries before proceeding.
. While you press and hold /FIND HANDSET, plug the telephone base power adapter back to the
power outlet.
3. After about 0 seconds, when the IN USE light starts flashing, release /FIND HANDSET and then press it
again within 3 seconds.
When the phone successfully enters the CEC battery charging test mode, you hear a confirmation tone,
/ANS ON/OFF turns on. The IN USE light and the DOORBELL light temporarily turn on for about 60
and
seconds. All handsets display Put handset on BASE to register.
When the phone fails to enter this mode, repeat Step  through Step 3 above.
Note: The telephone base will be powered up as normal if you fail to press /FIND HANDSET within
3 seconds in Step 3.
To deactivate the CEC battery charging testing mode:
. Unplug the telephone base power adapter from the power outlet, then plug it back in. Then the telephone
base is powered up as normal.
. Register your handsets back to the telephone base. See page 3 for handset registration instructions.


Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Is7121Is7121-2Is7121-22

Table of Contents