Summary of Contents for Impex MARCY DIAMOND ELITE MD-3401
Page 1
MD-3401 HOME GYM Safety Notice Hardware Identifier Assembly Instruction Parts List Warranty Ordering Parts Model MD-3401 Retain This Manual for Reference 120609 OWNER'S ® MANUAL IMPEX INC. 2801 S. Towne Ave, Pomona CA 91766 Tel: (800) 999-8899 Fax: (626) 961-9966 www.impex-fitness.com info@impex-fitness.com...
WARRANTY....................… ORDERING PARTS..................BEFORE YOU BEGIN ® by IMPEX Thank you for selecting the MARCY DIAMOND Home Gym MD-3401 For your safety and benefit, read this manual carefully before using the machine. As a manufacturer , we are committed to provide you complete customer satisfaction. If...
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT. SAVE THESE INSTRUCTIONS.
Meijer.com WARNING LABEL PLACEMENT The warning labels shown here have been placed on the Rear Stabilizer and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in the location shown.
Meijer.com ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches NOTE: It is strongly recommended that this machine be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Insert two Guide Rods (#16) into the holes on the Rear Stabilizer (#15). Secure each Guide Rod with one M10 x ¾”...
Page 10
Meijer.com STEP 2 (See Diagram 2) A.) Attach the Upper Frame (#1) onto the two Guide Rods (#16). Secure it with two M10 x ¾” Allen Bolts (#78) and ¾” Washers (#92). DO NOT tighten the Bolts yet. B.) Place the Upper Frame (#1) onto the Vertical Frame (#4). Secure it with two M10 x 2 ¾”...
Page 11
Meijer.com STEP 3 (See Diagram 3) A.) Attach the Front Press Base (#2) to the Upper Frame (#1). Secure it with one 6 ¾” Front Press Base Axle (#29), two Ø 1 ¼” Washers (#59), and two M10 Aircraft Nuts (#91). B.) Attach the Front Press (#3) to the Front Press Base (#2).
Page 13
Meijer.com STEP 4 (See Diagram 4) A.) Attach the Seat (#32) to the Seat Post (#6). Secure it with two M8 x 1 5/8” Allen Bolts (#86) and Ø 5/8” Washers (#88). B.) Insert the Seat Post into the opening on the Seat Support Frame (#7). Thread the Lock Knob (#40) into the hole on the Seat Support Frame to lock the Seat at selected height.
Page 14
Meijer.com STEP 5 (See Diagram 5) A.) Slide the Right Butterfly (#10) onto the right axle on the Butterfly Base (#13). B.) Insert the Butterfly Handle (#9) into the pivot on the Right Butterfly. Secure it with one M10 x ¾” Allen Bolt (#78) and 1 ¼” Washer (#59) from the bottom. C.) Repeat Procedures A and B above to install the other side.
Page 16
Meijer.com A.) Attach the 165” Upper Cable (#33) to the opening on the front of Upper Frame (#1). Make sure the ball stopper is underneath the Frame. Attach a Pulley (#47) to the Cable. B.) Secure the Pulley to the opening with one M10 x 3 ½” Allen Bolt (#77), two Pulley Bushings (#49), and one M10 Aircraft Nut (#91).
Page 19
Meijer.com STEP 7 (See Diagram 7 & Lower Cable Loop Diagram) A.) Attach the 164” Lower Cable (#35) to the opening on the Leg Developer (#8). Attach a Pulley (#47) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#84), two 7/8”...
Page 22
Meijer.com A.) Clip one end of the 98” Butterfly Cable (#34) to the open slot on the Right Butterfly (#10). B.) Draw the Cable to the open bracket on the right side of the Vertical Frame (#4). Attach a Small Pulley (#73) to the bracket C.) Secure it with one M10 x 1 ¾”...
Page 25
Meijer.com STEP 9 (See Diagram 9) A.) Connect the Lat Bar (#24) to the Upper Cable (#33) with two Hooks (#37) and one Chain (#36). B.) Connect the Abdominal Strap (#70) to the Lower Cable (#35) with a Hook. C.) Connect the Shiver Bar (#19) to the Lower Cable with two Hooks and a Chain. Replace Shiver Bar with Single Handle (#68) or Ankle Strap (#69) for various exercises.
Page 26
Meijer.com Step 10 (See Diagram 10) A.) Attach the two Weight Stack Covers (#74) with four 3” Sleeve (#94) to the Upper Frame (#1) and Rear Stabilizer (#15). B.) Secure them with four M10 x 3¾” Allen Bolts (#82) and four Ø ¾” Washers (#92). DIAGRAM 10...
Meijer.com WEIGHT RESISTANCE CHART WEIGHT PLATE Station Low Pulley Lat Pull Butterfly Front Press AB Crunch Leg Developer WEIGHT PLATE Station Low Pulley Lat Pull Butterfly Front Press AB Crunch Leg Developer *Numbers are approximate. Actual weight may vary. *Value for butterfly is for each arm.
Meijer.com PARTS LIST KEY NO. DESCRIPTION Q’ty Upper Frame Ø 1 ¼” Front Press Bushing Front Press Base Ø 7/8” Leg Developer Bushing 1” Bushing Front Press Vertical Frame Ø 1” Spacer Backrest Support Frame Rubber Bumper Seat Post Ø...
IMPEX. IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or performance of the product or other damages with respect to any economic loss, loss of property, loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other consequential damages or whatsoever natures.