Sola Control Interface And Menus - Weil-McLain SlimFit Manual

SlimFit
™
commercial condensing gas

Sola control interface and menus

Trend Analysis Snapshot
1. The trend analysis snapshot file is stored in Comma Separated
Value (CSV) format in the display so it can be imported into a
spreadsheet program such as Microsoft Excel. The trend analysis
snapshot file can be viewed in graph form on the display. It can
also be copied to a USB device.
2. To save the trend analysis page, the SAVE button must be pressed
on the trend analysis page. From there, the trend file can be given
a name. To save to a USB drive, press VIEW SNAPSHOT, select
the snapshot, then press COPY TO USB (see Figure 73).
3. At any time, pressing the "camera" button on the top left corner in
the menu bar will capture a screenshot, which can be transferred
to a USB memory stick. Go to Home page--> Setup--> Display
Diagnostics--> Screenshot--> press the snapshot file on the list
--> Copy to USB.
System Configuration
(HOME PAGE SETUP)
1. Pressing the DISPLAY REFRESH button starts a search pro-
cedure.
a. A new boiler control is identified by "Unknown" status next
to its name in the boiler system list (see Figure 77).
b. "Unknown" indicates that configuration data has not been
retrieved from the control yet.
c. Once the control is located it must be synchronized with
the display before it can be displayed. New controls are not
displayed on the Home page until this synchronization is
performed.
Figure 77 System refresh and synchronize screen
System Synchronization
(HOME PAGE SETUP SYNCHRONIZE)
1. Manually synchronize configuration data from the connected
controls at any time.
2. A new control is visible when configuration and status data is
gathered from it.
a. This collection procedure takes a few minutes. The control is
marked as "Unknown" when no configuration information
exists. Normally, control configuration data collection only
needs to be performed when the control is initially installed.
66
-
fired water boiler
3. Press the SYNCHRONIZE button to begin synchronization
with the control.
Display setup
(HOME PAGE SETUP
1. The SETUP page allows the user to configure display settings.
Press the SETUP button on the Home page to bring up the Setup
page (See Figure 77).
2. Press the DISPLAY SETUP button to display options that can
be set by the user.
3. The GENERAL tab (Figure 78) contains the following settings:
a. Display alerts on Status Summary Bar? This determines
whether non-safety alerts will be shown on the summary bar
of the Status page.
b. Display empty parameter groups? This cleans up the home
page by hiding unused parameter groups.
c. Sound audio alarm for faults? This uses the display speaker to
sound an alarm on shutdown for Sola faults.
Figure 78
Display setup page - General setup tab
4. The COM1 and COM2 tabs contain the following settings:
a. Enable COM1/COM2 port — DO NOT change.
b. Modbus address range 1-N: Sets the range of Modbus ad-
dresses to search for connected devices (range is 1 to 250).
c. Modbus baud rate — DO NOT change.
DO NOT CHANGE COM SETTINGS OR BAUD
RATES
not to operate.
5. Pressing the DISPLAY DIAGNOSTICS button (
SETUP DISPLAY DIAGNOSTICS)
diagnostics. Normally, these diagnostics are applicable only for
factory testing purposes, but conditions may arise that warrant
this testing. The CONTROL SNAPSHOT button allows the
user to dump the current status and/or configuration settings of
any Sola control into a text document. The text document can be
viewed on the display, saved for later viewing, and can be written
to a USB stick for viewing on a PC or file transfer.
6. Press the GATEWAY to verify that ENABLE MODBUS GATE-
WAY? is NOT checked unless the boiler is connected to a BMS.
If a BMS is used, see the SlimFit Modbus manual for details.
7. Press the Screen Saver tab to select the screen saver and to set
screen saver idle wait time.
— Boiler Manual
(continued)
DISPLAY SETUP)
. Changing these settings can cause the control
permits display hardware
Part number 550-100-116/0713
HOME PAGE