Hide thumbs Also See for 2441TH:

Advertisement

Quick Start Guide

INSTEON® Thermostat
Models: #2441TH, 2732-422, 2732-522

About INSTEON Thermostat

-
Confirm your existing system does not have a heat pump
-
Confirm your system has 4 or 5 wires (if 4 wires, you'll need an
"add-a-wire" adapter)
-
Installation should only be performed by a qualified HVAC
technician or a homeowner who is familiar and comfortable with
electrical circuitry. If you have questions, consult an HVAC
Technician or call the INSTEON Support Line at 866-243-8022.
-
Tools needed: flathead screwdriver and wire cutter/stripper
-
Add zone control to the system by adding INSTEON Wireless Thermostats

Installation

1)
Do not remove wires from existing thermostat until instructed to do so.
2)
If you have A/C, turn off A/C breaker.
a.
Confirm A/C is off by turning on air and observing that compressor/fan does not come on.
3)
Turn off breaker/fuse to furnace.
a.
If thermostat has no power, proceed to step 4.
b.
Try to turn on heat. If it does not come on, proceed to step 4.
c.
Otherwise, turn off heat and wait until furnace fan stops. Turn off other breakers until heat no longer runs.
4)
Remove cover from thermostat to gain access to wires (may need to detach from wall).
5)
If necessary, take photo of wiring connections to help with reconnections.
6)
If possible, while still connected, attach "C" label to wire connected to "C" on thermostat.
7)
Disconnect your C wire from thermostat. Label wire if necessary.
8)
Repeat steps 6 and 7 for all remaining wires.
9)
Remove existing thermostat backplate from wall.
10) Remove 3" of the outer jacket covering the bundle of wires (the jacket cannot remain
inside INSTEON Thermostat or device may malfunction). If you cannot get the
individual wires to extend 3" beyond outer jacket, you will need to splice on extension
wires.)
11) Slide wires (but not outer jacket) through the black draft shield grommet.
12) Mount INSTEON Thermostat to wall.
13) Insert C wire into terminal C and tighten.
14) Repeat for other wires matching terminal designations.
15) Close front of INSTEON Thermostat onto back mounting plate until you hear a click.
16) Turn on breaker(s).
17) After a few seconds INSTEON Thermostat will display the ambient temperature.
If INSTEON Thermostat displays a two-digit error code, open the unit and tap the reset button. Close unit and wait a few
seconds as it restarts. If problem persists, call the INSTEON Support Line at 866-243-8022.

Getting Started

Button Name
Button Function
Up arrow
Adjust heat, cool or both setpoints up 1°.
Down arrow
Adjust heat, cool or both setpoints down 1°.
Mode
Cycle between modes (Heat, Cool, Auto, Time of Day and Off).
Set
Adding and removing INSTEON Thermostat to and from INSTEON scenes
Program
Adjust preprogrammed scenes (Wake, Leave, Return and Sleep).
Time/Sensor
Adjust clock settings.
Master
Press and hold to set as the "active" thermostat (with one or more INSTEON Wireless
Thermostats).
Fan
Cycle between fan-always and fan-auto.
Hold
Lock current settings (until tapped again or INSTEON release command).
Energy (Leaf)
Save energy by dropping the heat and cool setpoints by 4° (adjustable).

Set Clock

1)
Tap Time/Sensor button.
2)
Tap Up or Down arrow until current hour and AM/PM are shown.
3)
Tap Time/Sensor again.
4)
Tap Up or Down arrow until current minutes are shown.
5)
Tap Time/Sensor again.
6)
Tap Up or Down arrow button until current day is shown.
7)
Tap Mode to exit.
#2441TH, 2732-422, 2732-522 Rev. 11/7/2012 10:06 AM / See Owner's Manual for Warranty Information.
Protected under U.S. and foreign patents (see www.insteon.com)
© Copyright 2012 INSTEON, 16542 Millikan Ave., Irvine, CA 92606, 866-243-8022
Hours will blink.
Minutes will blink.
Day will blink.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 2441TH and is the answer not in the manual?

Questions and answers

Summary of Contents for INSTEON 2441TH

  • Page 1: Quick Start Guide

    17) After a few seconds INSTEON Thermostat will display the ambient temperature. If INSTEON Thermostat displays a two-digit error code, open the unit and tap the reset button. Close unit and wait a few seconds as it restarts. If problem persists, call the INSTEON Support Line at 866-243-8022.
  • Page 2 Tap Up and Down button to add to a Scene to Group 1 through 4 (default setting = Cooling mode, Group 1). Adjust scene responder to the state you want when scene is activated from INSTEON Thermostat (e.g. 50%, 25% or even off).

This manual is also suitable for:

2732-4222732-522

Table of Contents