Operation - Honeywell T7200D Product Data

T7200D,E, T7300D,E,F AND Q7300 SERIES 2000 PROGRAMMABLE COMMERCIAL THERMOSTATS AND SUBBASES
3. Press increase
or decrease
temperature offset is displayed (range is 0°F to 5°F).
Set Program Set Temperature
Run Occupied Unoccupied Occupied Unoccupied
Program Start Time Start Time Day Temp Temp
Temporary Set Current Clear Heat/Cool
Occupied Day/Time Start Time Copy Settings
Continous
Unoccupied System Fan
4. Press Run Program.
Run
Program
Set Program Set Temperature
Run Occupied Unoccupied Occupied Unoccupied
Program Start Time Start Time Day Temp Temp
Temporary Set Current Clear Heat/Cool
Occupied Day/Time Start Time Copy Settings
Continous
Unoccupied System
Using Temporary Override
NOTE: The temporary override temperature is held for one,
three, eight or twelve hours (depending on installer
setup number 26) and then the thermostat returns to
the program.
1. Press Temporary Occupied.
NOTE: The default temperature setting is the
Occupied setpoint.
Temporary
Set Program Set Temperature
Run Occupied Unoccupied Occupied
Occupied Program Start Time Start Time Day Temp
Temporary Set Current Clear
Occupied Day/Time Start Time Copy
Continous
Unoccupied System
2. Press increase or decrease
setting by the offset (range is 0°F to 5°F), if desired.
NOTE: With zero offset, the default setting changes in
one degree increments. If the offset is 1 - 5, the
default setting changes by ± the offset.
Set Program Set Temperature
Run Occupied Unoccupied Occupied Unoccupied
Program Start Time Start Time Day Temp Temp
Temporary Set Current Clear Heat/Cool
Occupied Day/Time Start Time Copy Settings
Continous
Unoccupied System Fan
3. Press Run Program to cancel the override.
Run
Program
Set Program Set Temperature
Run Occupied Unoccupied Occupied Unoccupied
Program Start Time Start Time Day Temp Temp
Temporary Set Current Clear Heat/Cool
Occupied Day/Time Start Time Copy Settings
Continous
Unoccupied System
Using Continuous Unoccupied
1. Press Continuous Unoccupied.
NOTE: The default temperature setting is the
Unoccupied setpoint. The default appears for
approximately five seconds and then the room
temperature is displayed.
Continuous
Set Program Set Temperature
Unoccupied
Run Occupied Unoccupied Occupied
Program Start Time Start Time Day Temp
Temporary Set Current Clear
Occupied Day/Time Start Time Copy
Continous
Unoccupied System
until the desired
Change
Time/Temp
M4981A
AM
Room
Change
Time/Temp
Mon
Occupied 1
System Fan
Fan
Heat Auto
M4954A
Setting
Change
Time/Temp
Unoccupied
Temp
Heat
Heat/Cool Override
Settings
Fan
M4982B
to change the default
Temporary
AM
Room
Change
Time/Temp
Wed
Override
System Fan
Auto Auto
M4983B
AM
Room
Change
Time/Temp
Mon
Occupied 1
System Fan
Fan
Heat Auto
M4954A
Setting
Change
Time/Temp
Unoccupied
Temp
Heat
Heat/Cool
Settings
Fan
M4984B
2. Press increase
setting, if desired.
Set Program
Run Occupied Unoccupied
Program Start Time Start Time
Temporary Set Current
Occupied Day/Time Start Time
Continous
Unoccupied
3. Press Heat/Cool Settings to change between heat and
cool settings. Press increase
the temperature settings.
4. Press Run Program to cancel the Hold and return to the
program.
Run
Program
Run Occupied
Program Start Time
Temporary Set Current
Occupied Day/Time
Continous
Unoccupied
Changing Temperature Setpoint Until Next
Program Period
1. Press increase
temperature is displayed.
NOTE: If or
display, it means that both the heat and cooling
setpoints are being adjusted. Tapping the key
changes both setpoints by one degree. Press
Heat/Cool Settings after the desired setpoint is
reached to review the settings.
Set Program
Run Occupied Unoccupied
Program Start Time Start Time
Temporary Set Current Clear
Occupied Day/Time Start Time
Continous
Unoccupied
2. Press Run Program to cancel the Hold and return to
the program.
Run
Program
Run Occupied
Program Start Time
Temporary Set Current
Occupied Day/Time
Continous
Unoccupied

OPERATION

T7200/T7300 Relay Logic
The T7200/T7300 contains three switching relays. In
conventional applications, the relays control first stage
cooling, first stage heating, and fan. In heat pump
applications, the relays control the heat pump compressor,
auxiliary heat, and the fan. Because of this change in
switching logic, it is important to use a Q7300C,D,
Q7300H2003, or Q7300H2011 Subbase when the T7300 is
set for heat pump applications and a Q7300A,G,
Q7300H2029 Subbase when the T7300 is set for
conventional applications.
The T7200D Relay Logic is for conventional applications.
The T7200E Relay Logic is for heat pump applications.
19
or decrease to change the default
Set Temperature Change
Time/Temp
Occupied Unoccupied
Day Temp Temp
Heat
Clear Heat/Cool
Copy Settings
System Fan
or decrease
AM
Set Program Set Temperature Change
Time/Temp
Unoccupied Occupied Unoccupied
Start Time Day Temp Temp
Mon
Occupied 1
Clear Heat/Cool
Start Time Copy Settings
System
System Fan
Heat
or decrease until the desired
appear under the temperature
Temporary Setting
Set Temperature Change
Time/Temp
Occupied Unoccupied
Day Temp Temp
Heat
Occupied
Heat/Cool
Copy Settings
System Fan
AM
Set Program Set Temperature Change
Time/Temp
Unoccupied Occupied Unoccupied
Start Time Day Temp Temp
Mon
Occupied 1
Clear Heat/Cool
Start Time Copy Settings
System
System Fan
Heat
Setting
M10232A
to adjust
Room
Fan
Auto
M4954A
M4987B
Room
Fan
Auto
M4954A
63-4355—4