Honeywell T7200D Product Data page 12

T7200D,E, T7300D,E,F AND Q7300 SERIES 2000 PROGRAMMABLE COMMERCIAL THERMOSTATS AND SUBBASES
Installer Setup
Number
(Press Unoccupied
Select Temp to change)
Extended fan 19
a
operation in heat
(T7300F only).
Extended fan 20
operation in
cooling
(T7300F only).
Fan key 21
adjustment
(models with Fan
key).
Remote sensing. 22
Temperature 23
b
averaging network
(T7300F only).
Not used. 24
Keypad lockout 25
level (keypad
lockout enabled/
disabled by DIP
switch 1 on
thermostat back).
(T7300F only)
Duration of 26
temporary
override.
Not used. 27 through 29
Deadband 30
(T7300F only).
Interstage control 31
point (T7300F,
Q7300C,D only).
Minimum on- time 32
(T7300F).
Minimum 33
compressor off-
time.
Temperature heat 34
range stops
(T7300F).
Temperature 35
cooling range
stops (T7300F).
Not used. 36
a
Number 2 must be set to 1 to extend fan operation.
b
Number 22 must be set to 1 and remote sensor(s) must be installed.
63-4355—4
Table 7. Thermostat Installer Setup Options. (Continued)
Factory Setting
Display Description
0 No extended fan operation after
call for heat ends.
0 No extended fan operation after
the call for cooling ends.
0 Fan setting key operational.
0 Remote sensing not activated.
0 Temperature averaging disabled.
— —
0 No lockout.
3 3: Three hour override.
— —
2 Heating and cooling setpoints can
be set no closer than 2°F (1.1°C).
0 Disabled.
2 2-minute minimum on- time for
heating and cooling.
4 4-minute minimum compressor
off-time.
90 Highest heat setpoint.
45 Lowest cooling setpoint.
— —
12
Other Choices
(Press or to change)
Display Description
1 Fan operation extended 90 sec after call for
heat ends.
1 Fan operation is extended 90 seconds after
the call for cooling ends.
1 Fan setting key is Auto only.
1 Remote sensing activated.
1 Temperature averaging between local
sensor and remote sensor(s) activated.
— —
1, 2 or 3 1: Lockout all thermostat keys except
system and fan settings, temporary
setpoint, clock and day adjustments,
increase and decrease
2: Lockout all keys except Set Current Day/
Time, increase and decrease
3: Lockout all keys except Temporary
Occupied and Set Current Day/Time (for
clock, day adjustment).
1, 8 or 1: One hour override.
12 8: Eight hour override.
12: Twelve hour override.
— —
3 - 10 Heating and cooling setpoints can be set no
closer than the chosen value.
1 - 12 Temperature must change more than
chosen value before system calls for next
stage. (Example: heat setpoint: 68°F (20°C),
interstage setting: 2°F (1.1°C), temperature
is 65.5°F (18.5°C). Second stage turns on,
brings temperature to 66°F (19°C) and turns
off. Heat pump continues to run until setpoint
is reached.
0 or 1 No minimum on-time or 1-minute minimum
on-time for heating and cooling.
0, 1, 2, 3 Minimum number of minutes (0 through 5)
or 5 compressor is off between compressor calls.
40 to 89 Heat setpoint temperature range (1°F
increments).
46 to 99 Temperature range (1°F increments) for
cooling setpoint.
— —
Actual
Setting
—
.
.
—
—