Table of Contents
Advertisement
maytag atlantis washer repair spin bearing thats noisy, diy
this is my experience repairing the maytag washer Atlantis mav series 9750 aww, I had to
replace the spin bearing since it was making a jet engine noise when it was spinning out the
water. its not an easy job for my 1st time taking this machine apart, you literally take it all apart
to get to this bearing, but now I can show how to do it with pictures making it easier for you to do
it. even if you have to replace something other than the spin bearing, this how to tutorial will
show you how to get to most of the parts in this machine
one way to test for spin bearing noise is to lift up top part of machine with the lid taped
down, explained below, put it in spin cycle, and quickly place the palms of your hand inside
of basket pushing against opposite ends in the basket to stop it from turning, yes it can be
done because it takes a while before it starts spinning at full speed, if noise has gone away, its
your spinner bearing. do not repeat until you stopped the machine and start over again
email me if you have any questions, remove "<remove>" this part in the email address before
here is a link for for a breakdown on all the parts of the washing machine
file:///D|/Documents%20and%20Settings/DJ/Meus%20documentos/Web/Publicar/pe...g%20atlantis%20washer%20repair%20spin%20bearing%20thats%20noisy,%20diy.htm (1 of 34) [4/5/2008 19:16:25]
maytag Atlantis washer repair
vincom5<remove>@yahoo.com
http://www.appliancepartspros.com/partsearch/model.aspx?model_id=47955
you also you can download the
mav9750 aww
you send
maytag washer repair manual
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Maytag mav9750 aww
Summary of Contents for Maytag mav9750 aww
- Page 1 Atlantis washer repair mav9750 aww this is my experience repairing the maytag washer Atlantis mav series 9750 aww, I had to replace the spin bearing since it was making a jet engine noise when it was spinning out the water.
- Page 2 (see pics below in section on removing hub and seal...
- Page 3 TAKING APART THE MACHINE STEP 1: belt removal: first step is to take off drive belt underneath the machine, its easy, tilt machine back to lean against a wall, grab the belt and pull it off one of the front pulleys.
- Page 4 STEP 2: lift the top: next is to lift the top part of the machine, tape the lid down to the top (not to sides or front panel), use a putty knife and slide it into the front corner in between the seam of the top and...
- Page 5 STEP 3; agitator removal: now you have the top up, its time to remove the agitator, lift off the fabric softener dispenser, its just snaps on, so just lift it up. now you will see down the middle of agitator and see a screw, use an socket wrench w/ an extension and remove screw counter clockwise (screw can remain in agitator opening), then just grab bottom of agitator and lift up.
- Page 6 STEP 4: water spout: now you will have to move the water spout out of the way, you can disconnect the hoses from the back of the water inlet valve, which is part of the water spout, and disconnect the wires to...
- Page 7 STEP 5: front panel removal : next we have to remove front panel, it is held by 2 screws on top, and tabs on bottom, once you remove the screws, the panel swings out and you lift it up off the tabs which are on the...
- Page 8 (8 of 34) [4/5/2008 19:16:25]...
- Page 9 (9 of 34) [4/5/2008 19:16:25]...
- Page 10 STEP 7: inner tub removal: we can remove the four bolts holding inner tub (spinner) to the outer tub file:///D|/Documents%20and%20Settings/DJ/Meus%20documentos/Web/Publicar/p...%20atlantis%20washer%20repair%20spin%20bearing%20thats%20noisy,%20diy.htm (10 of 34) [4/5/2008 19:16:25]...
- Page 11 4 bolts are out, the tub will come out, as you move it up move water spout out of the way STEP 8: o-ring, seal nut, and hub removal: remove the o-ring on the shaft (not visible in pic below), I used a small knitting needle to get the o-ring off.
- Page 12 I used a hammer to hit the pliers to turn it in a counter clockwise direction, once you get it to start turning it should come out easily.
- Page 13 (13 of 34) [4/5/2008 19:16:25]...
- Page 14 STEP 9: outer tub removal: (the next part I thought I could just take out the outer tub without removing the load balancing springs that hold down the transmission unit to the frame, I was wrong, if your model...
- Page 15 I removed the basket first, there...
- Page 16 water.
- Page 17 (17 of 34) [4/5/2008 19:16:25]...
- Page 18 STEP 10: spring removal: the seal and bearing housing is screwed into dome from underneath with 3 screws, so we have to unhook the springs to get the transmission unit out. you can use a special tool that helps...
- Page 19 (basket) still attached. file:///D|/Documents%20and%20Settings/DJ/Meus%20documentos/Web/Publicar/p...%20atlantis%20washer%20repair%20spin%20bearing%20thats%20noisy,%20diy.htm (19 of 34) [4/5/2008 19:16:25]...
- Page 20 STEP 11: dome removal: there are 3 legs attached to the dome, mark the relationship for reassembly, remove the screws holding the legs to the dome, 2 for each leg, total of 6 screws to remove...
- Page 21 removed.
- Page 22 STEP 12: seal and bearing housing removal: file:///D|/Documents%20and%20Settings/DJ/Meus%20documentos/Web/Publicar/p...%20atlantis%20washer%20repair%20spin%20bearing%20thats%20noisy,%20diy.htm (22 of 34) [4/5/2008 19:16:25]...
- Page 23 (23 of 34) [4/5/2008 19:16:25]...
- Page 24 I needed to replace, the seal and bearing are part of this housing, the new unit will be "seal and bearing kit" replacement file:///D|/Documents%20and%20Settings/DJ/Meus%20documentos/Web/Publicar/p...%20atlantis%20washer%20repair%20spin%20bearing%20thats%20noisy,%20diy.htm (24 of 34) [4/5/2008 19:16:25]...
- Page 25 STEP 13: installing the new seal and bearing housing: the new seal and bearing kit comes with gaskets and a new redesigned hub, here is a link to the http://www.appliancepartspros.com/partsearch/ctrfs. aspx?part_id=3875413&&model_id=47955&diagram_id=646306 "no"...
- Page 26 STEP 14 reinstalling the parts: place transmission unit over something soft as not to damage the pulley at the bottom, slide dome over shaft and line up your relationship marks, bang it down with your hand until the...
-
Page 27: Bearing Housing
I placed the new black rubber seal onto the the seal and bearing housing file:///D|/Documents%20and%20Settings/DJ/Meus%20documentos/Web/Publicar/p...%20atlantis%20washer%20repair%20spin%20bearing%20thats%20noisy,%20diy.htm (27 of 34) [4/5/2008 19:16:26]... - Page 28 (28 of 34) [4/5/2008 19:16:26]...
- Page 29 I screwed the outer basket back on to the dome, and the four screws inside the basket which screw into the bearing housing.
- Page 30 I hope this helps you doing what I needed to do, I wish someone made a site like this for before I did this job email me if you have any questions, remove "<remove>" this part in the email address before you send vincom5<remove>@yahoo.com...
- Page 31 (31 of 34) [4/5/2008 19:16:26]...
- Page 32 (32 of 34) [4/5/2008 19:16:26]...
- Page 33 Atlantis washer repair spin bearing noisy spinning water maytag Atlantis washer maytag Atlantis washer maytag Atlantis washer maytag Atlantis washer spin bearing noisy spin bearing noisy maytag maytag maytag washer...
- Page 34 Atlantis washer repair spin bearing noisy spinning water maytag Atlantis washer maytag Atlantis washer maytag Atlantis washer maytag Atlantis washer spin bearing noisy spin bearing noisy maytag maytag maytag washer repair washer repair washer repair file:///D|/Documents%20and%20Settings/DJ/Meus%20documentos/Web/Publicar/p...%20atlantis%20washer%20repair%20spin%20bearing%20thats%20noisy,%20diy.htm (34 of 34) [4/5/2008 19:16:26]...
Need help?
Do you have a question about the mav9750 aww and is the answer not in the manual?
Questions and answers