Chapter 3. Mechanism Blocks; General Description - Sharp UX-B700 Service Manual

CHAPTER 3. MECHANISM BLOCKS

[1] General description

1. Document feed block and diagram
Document guide upper
Front sensor
Original sensor
Back roller
Pinch roller
CIS
Exit roller
2. Document feed operation
1) The original, which is set in the document hopper, feeds automati-
cally when the front sensor is activated. This in turn activates the
drive motor which drives the paper feed roller. The document stops
when the lead edge is detected by the original sensor.
2) The lead edge of the original is fed a specified number of pulses after
the lead edge of the document is detected for the reading process to
begin.
3) The trailing edge of the original is fed a specific number of pulses
after the trailing edge of the document deactivates the original sen-
sor. The read process then stops and the original is discharged.
4) When the front sensor is in the OFF state (any document is not set
up in the hopper guide), the drive will be stopped when the docu-
ment is discharged.
3. Hopper mechanism
3-1. General view
The hopper section contains document guides that are used to adjust
the hopper to the width of the original document. This ensures that the
original feeds straight into the fax machine for scanning.
Document width: 148 mm to 216 mm (A5 longitudinal size to Letter
longitudinal size)
NOTE: Adjust the document guide after setting up the document.
Document
Paper feed roller
Fig. 1
Fig. 2
3-2. Automatic document feed
1) Use of the paper feed roller and separate plate ensures error-free
transport and separation of documents. The plate spring presses the
document to the paper feed roller to assure smooth feeding of the
document.
2) Document separation method: Separate plate
Paper feed plate
Separate rubber
Separate plate
Sub feed plate
Document guide upper
3-3. Documents applicable for automatic feed
Paper weight 70 kg
21.5 lbs.
(80 g/m
Paper thickness (ref.) 0.1 mm
Paper size LGL (216 mm x 355.6 mm)
A4 (210 mm x 297 mm)
LTR (216 mm x 279 mm)
Feeder capacity A4/LTR: 20 sheets
LGL
NOTE: Double-side coated documents and documents on facsimile re-
cording paper should be inserted manually. The document feed
quantity may be changed according to the document thickness.
Documents corresponding to a paper weight heavier than 70 kg (81.4g/
m 2 ) and lighter than 135 kg (157 g/m
Documents heavier than 135 kg in terms of the paper weight must be
duplicated on a copier to make it operative in the facsimile.
3-4. Loading the documents
1) Make sure that the documents are of suitable size and thickness,
and free from creases, folds, curls, wet glue, wet ink, clips, staples
and pins.
2) Place documents face down in the hopper.
i) Adjust the document guides to the document size.
ii) Align the top edge of documents and gently place them into the
hopper. The first page under the stack will be taken up by the
feed roller to get ready for transmission.
NOTES: 1) Curled edge of documents, if any, must be straightened
out.
2) Do not load the documents of different sizes and/or
thicknesses together.
Last page of document
Paper feed plate
Separate rubber
Separate plate
Sub feed plate
Document guide upper
3 – 1
UX-B700U
FO-B1600U
Document
Document guide lower
Paper feed roller
Fig. 3
20 sheets 1sheet(Manual)
70 kg ~ 135 kg
14 lbs. ~ 42 lbs.
2 ) (52 g/m 2 ~ 157g/m
0.1 mm ~ 0.18mm
: 5 sheet
2 ) are acceptable for manual feed.
Back of document
First page of document
Document
Document guide lower
Paper feed roller
Fig. 4
2 )