Samsung CLX-9252 9352 Series User Manual page 239

Message Meaning
Prepare new The estimated life of
Transfer roller. the transfer roller is
close.
Punch hopper The punch hopper
container is Full or container is full or not
not installed. installed.
Remove seal tape The seal tape of the
of [color/black] imaging unit is not
imaging unit and removed.
reinstall.
Replace with new The indicated imaging
[color/black] unit has almost
imaging unit. reached its estimated
imaging unit life. The
machine will stop
printing.
Replace with new The life of the fuser
fuser unit. unit expires totally.
Replace with new The life of the transfer
Transfer roller. roller expires totally.
Replace with new The life of the tray
[tray number] pickup roller expires
pickup roller. totally.
Replace with new The life of the MP
MP pickup roller. pickup roller expires
totally.
Right door is open. The door is not
Close it. securely latched.
Scanner locked or The CCD (Charged
another problem Couple Device) lock
occurred. has been locked.
Scan System There is a problem in
Failure [error the scan system.
number]:Turn off
then on.
Second fax modem The second optional
card is not fax multiline kit is not
installed. Install installed.
the card.
Shake [color] toner Small amount of toner
cartridge. is left in the indicated
cartridge.
Suggested solutions
Prepare a new transfer
roller for a replacement.
Empty the punch hopper
container. Or install the
punch hopper container.
Remove the seal tape of
the imaging unit (see
"Replacing the imaging
unit" on page 195).
Replace the imaging unit
with a Samsung-genuine
imaging unit (see
"Replacing the imaging
unit" on page 195).
Replace the fuser unit
with a Samsung-genuine
fuser unit.
Replace the transfer
roller with a
Samsung-genuine
transfer roller.
Replace the tray pickup
roller with a
Samsung-genuine pickup
roller.
Replace the MP pickup
roller with a
Samsung-genuine MP
pickup roller.
Close the door until it
locks into place.
Unlock the CCD lock . Or
turn the machine off and
back on again. If the
problem persists, call for
service. Scanner
Turn the machine off and
back on again. If the
problem persists, call for
service.
Install the optional fax
multiline kit. If it is already
installed, try to reinstall
the optional fax multiline
kit. If the problem
persists, call for service.
You may temporarily
increase the printing
quality by redistributing
the toner (see
"Redistributing toner" on
page 188).
Troubleshooting_ 239
Message Meaning
Side feeder door is The door is not
open. Close it. securely latched.
Staple cartridge is The staple cartridge
empty. Replace it. has reached the end
of its lifespan.
Staple cartridge is Small amount of
low. Replace staple cartridge is left.
cartridge. The estimated life of
staple cartridge is
close.
Staple cartridge is The staple cartridge is
not installed. not installed or the
Install it in finisher. staple cartridge is not
properly installed.
Staple cartridge of The staple cartridge of
booklet I is empty. booklet has reached
Replace cartridge. the end of its lifespan.
Staple cartridge of Small amount of
booklet I is low. staple cartridge of
Replace cartridge. booklet is left. The
estimated life of staple
cartridge is close.
Staple cartridge of The staple cartridge of
booklet I is not booklet is not installed
installed. Install or the staple cartridge
the cartridge. is not properly
installed.
The clock became The time setting of
initial time. Set a machine is initialized.
time again.
Too much media in The center tray is full.
the center tray.
Remove printed
media.
Too much media in The booklet tray is full.
booklet tray.
Remove printed
media.
Too much media in The finishing tray is
finisher tray. full.
Remove printed
media.
Top door of
The duplex automatic
scanner is open.
document feeder
cover is not securely
latched.
Suggested solutions
Close the door until it
locks into place.
This message appears
when the staple cartridge
is completely empty.
Replace the staple
cartridge.
Prepare a new staple
cartridge for a
replacement.
Install the staple
cartridge. If it is already
installed, try to reinstall
the staple cartridge. If the
problem persists, call for
service.
This message appears
when the staple cartridge
is completely empty.
Replace the staple
cartridge.
Prepare a new staple
cartridge for a
replacement.
Install the staple
cartridge. If it is already
installed, try to reinstall
the staple cartridge. If the
problem persists, call for
service.
Set the time setting in
Machine Setup.
Remove printouts from
the center tray, the
machine resumes
printing.
Remove printouts from
the booklet tray, the
machine resumes
printing.
Remove printouts from
the finishing tray, the
machine resumes
printing.
Close the cover until it
locks into place.