Samsung CLX-9252 9352 Series User Manual page 237

Message Meaning
HDD System There is a problem in
Failure [error the hard disk.
number]:Turn off
then on.
ICON device is not The image converter
installed. Install device is not installed.
the device.
Input System There is a problem in
Failure [error the high capacity
number]:Check the feeder.
HCF connection.
Input System There is a problem in
Failure [error the tray.
number]:Pull [tray
number] out and
insert it.
ITB Unit Failure There is a problem in
[error the image transfer belt
number]:Turn off unit.
then on.
MSOK System There is a problem in
Failure [error the engine system.
number]:Turn off
then on.
Network cable is The machine is not
disconnected. connected with a
Check it. network cable.
Option Feed door The door is not
is opened. Close it. securely latched.
Original paper jam The originals are
in exit area of jammed in duplex
scanner automatic document
feeder.
Original paper jam The originals are
in front of scanner jammed in duplex
automatic document
feeder.
Original paper jam The originals are
inside of scanner jammed in duplex
automatic document
feeder.
Output tray(face The output tray (face
down) is full. down) is full.
Remove printed
media
Suggested solutions
Turn the machine off and
back on again. If the
problem persists, call for
service.
Install the image
converter device. If it is
already installed, try to
reinstall the image
converter device. If the
problem persists, call for
service.
Open and close the high
capacity feeder, or check
the high capacity feeder
connection with the
machine. If the problem
persists, call for service.
Open and close the tray.
If the problem persists,
call for service.
Turn the machine off and
back on again. If the
problem persists, call for
service.
Turn the machine off and
back on again. If the
problem persists, call for
service.
Connect the machine to
the network with a
network cable.
Close the door until it
locks into place.
Clear the jam (see
"Original paper jam in exit
area of scanner" on
page 206).
Clear the jam (see
"Original paper jam in
front of scanner" on
page 201).
Clear the jam (see
"Original paper jam inside
of scanner" on page 202
or "Original paper jam in
front of scanner duplex
path" on page 204).
Remove papers from the
output tray (face down),
the machine resumes
printing.
Troubleshooting_ 237
Message Meaning
Output tray(face The output tray (face
up) is full. Remove up) is full.
printed media
Paper is empty in There is no paper in
[tray number]. the tray.
Load paper.
Paper is empty in There is no paper in
tray MP. Load the multi-purpose tray.
paper.
Paper is low in Running out of paper
[tray number]. in the tray.
Load paper.
Paper jam after Paper has jammed
booklet folding. during booklet
printing.
Paper jam around Paper has jammed
puncher of finisher during finishing.
Paper jam at Paper has jammed
entrance of during finishing.
finisher
Paper jam at Paper has jammed
entrance of booklet during booklet
maker. printing.
Paper jam at Paper has jammed
entrance of during finishing.
finisher bridge
Paper jam at exit of Paper has jammed
finisher during finishing.
Paper jam at exit of Paper has jammed
finisher bridge during finishing.
Paper Jam at the Paper has jammed
bottom of duplex during duplex printing.
path
Paper Jam at the Paper has jammed
inside of duplex during duplex printing.
path
Suggested solutions
Remove papers from the
output tray (face up), the
machine resumes
printing.
Load paper in the tray.
Load paper in the
multi-purpose tray.
Load paper in the tray.
Clear the jam (see "Paper
jam after booklet folding
(3,250-sheet booklet
finisher only)" on
page 233).
Clear the jam (see "Paper
jam around puncher of
finisher" on page 228).
Clear the jam (see "Paper
jam at entrance of
finisher" on page 226).
Clear the jam (see "Paper
jam at entrance of
booklet maker
(3,250-sheet booklet
finisher only)" on
page 228).
Clear the jam (see "Paper
jam inside of finisher
bridge" on page 226 or).
Clear the jam (see "Paper
jam at finisher's exit
during ejection to the top
bin" on page 223 or
"Paper jam at finisher's
exit during ejecting to
main bin" on page 224).
Clear the jam (see "Paper
jam at entrance of
finisher" on page 226).
Clear the jam (see "Paper
jam bottom of duplex
path (Jam Duplex Regi.)"
on page 221).
Clear the jam (see "Paper
jam at the inside of
duplex path (Jam Duplex
2)" on page 220).