Related Manuals for Hoist Fitness HD1610
Summary of Contents for Hoist Fitness HD1610
- Page 1 HD1610 LEG PRESS / TOE RAISE Note: Both Serial Number and Model Number are Required when Ordering Parts Customer Service RECORD SERIAL NUMBER HERE (800) 548-5438 (858) 578-7676 CATALOG NUMBER (858) 578-9558 1106 - 003...
-
Page 2: Table Of Contents
OWNER'S MANUAL CONTENTS INSTRUCTIONS ..............FRAME ASSEMBLY .............. PRE-ASSEMBLY..............DECAL PLACEMENT............. DECAL REFERENCE............. PART LIST................ABBREVIATIONS..............BOLT SIZING CHART............WASHER SIZING CHART............MAINTENANCE SCHEDULE..........GENERAL MAINTENANCE INFORMATION......WEIGHT TRAINING TIPS............WEIGHT RATIOS..............EXERCISE LOG..............LIMITED WARRANTY............HD1610 ASSEMBLY PAGE 01... -
Page 3: Instructions
If you experience problems, first recheck the assembly instructions to locate any possible errors made during assembly. If you are unable to correct the problem, call your authorized HOIST dealer. Be sure to have your serial number and this manual when calling. When all parts have been accounted for, continue on. - Page 4 OWNER'S MANUAL ***THIS PAGE WAS INTENTIONALLY LEFT BLANK*** HD1610 ASSEMBLY PAGE 03...
-
Page 5: Frame Assembly
OWNER'S MANUAL FRAME ASSEMBLY PAGE 04 HD1610 ASSEMBLY... - Page 6 OWNER'S MANUAL FRAME ASSEMBLY NOTE: - HAND TIGHTEN HARDWARE. 5212.37 205 3/16" HD1610 ASSEMBLY PAGE 05...
- Page 7 OWNER'S MANUAL FRAME ASSEMBLY NOTE: - HAND TIGHTEN HARDWARE. USE ONLY WHEN ASSEMBLY TO MULTI-STATION HMG-4000 (REPLACE ITEM #10) PAGE 06 HD1610 ASSEMBLY...
- Page 9 OWNER'S MANUAL FRAME ASSEMBLY NOTE: - WRENCH TIGHTEN HARDWARE. - SOME PARTS MAY HAVE BEEN REMOVED FOR CLARITY. PAGE 08 HD1610 ASSEMBLY...
- Page 10 OWNER'S MANUAL FRAME ASSEMBLY NOTE: - WRENCH TIGHTEN HARDWARE (98) THEN LOOSEN NUT JUST ENOUGH FOR (11) TO PIVOT FREELY. - SOME PARTS MAY HAVE BEEN REMOVED FOR CLARITY. - WRENCH TIGHTEN ALL OTHER HARDWARE. HD1610 ASSEMBLY PAGE 09...
- Page 14 OWNER'S MANUAL FRAME ASSEMBLY NOTE: - WRENCH TIGHTEN HARDWARE. - SOME PARTS MAY HAVE BEEN REMOVED FOR CLARITY. HD1610 ASSEMBLY PAGE 13...
- Page 15 THROUGH TUBE WARNING - CABLE BOLT MUST BE THREADED A MINIMUM OF 3/8" WITH JAM NUT TIGHTENED NOTE: SECURELY TO ENSURE PROPER CONNECTION. BE SURE CABLE RUNS BETWEEN THE PULLEYS AND THE GUARD PIN. JAM NUT PAGE 14 HD1610 ASSEMBLY...
- Page 17 OWNER'S MANUAL FRAME ASSEMBLY NOTE: - WRENCH TIGHTEN HARDWARE. - SOME PARTS MAY HAVE BEEN REMOVED FOR CLARITY. PAGE 16 HD1610 ASSEMBLY...
- Page 18 OWNER'S MANUAL PRE-ASSEMBLY YELLOW END CAP USE ONLY WHEN ASSEMBLY TO MULTI-STATION HGM-4000 HD1610 ASSEMBLY PAGE 17...
-
Page 20: Decal Placement
OWNER'S MANUAL DECAL PLACEMENT HD1610 ASSEMBLY PAGE 19... -
Page 21: Decal Reference
OWNER'S MANUAL DECAL REFERENCE 021-0003543 021-0003113 021-0003221 SERIAL # DECAL 021-0003254 021-0003131 021-0003551 021-0003334 021-0003130 PAGE 20 HD1610 ASSEMBLY... - Page 22 OWNER'S MANUAL DECAL REFERENCE 021-0013313 021-0013314 HD1610 ASSEMBLY PAGE 21...
- Page 23 OWNER'S MANUAL ***THIS PAGE WAS INTENTIONALLY LEFT BLANK*** PAGE 22 HD1610 ASSEMBLY...
-
Page 24: Part List
026-01PL0290 WHITE SPACER 026-01PL0235-23 1.188" DIA X 8.75" OPEN END GRIP 026-01T3419 ADJUSTER TUBE 026-STD-06-0193 2.00" X 3.00" BULLNOSE END CAP (BLACK) 026-01G0215 SHAFT, .984" X 29.94" LG. 026-01PL2179 PLASTIC SCUFF GUARD 026-01T0545 WEIGHT STACK MOUNT HD1610 ASSEMBLY PAGE 23... - Page 25 WEIGHT PLATE BUSHING 014-0015015 INTERNAL SNAP RING-1.00" HSG 016-0001003 END CAP 1.50" X 2.50" (BLACK) 021-0018022 HOISTFITNESS.COM LOGO 021-0003254 DECAL HOIST .092" X 3.38" 021-0003334 DECAL HOIST 3.90" X 14.25" 021-0013313 HD1610 PLACARD (LEFT) 021-0013314 HD1610 PLACARD (RIGHT) 021-0003551 DECAL ADJUST 1-11 DECAL VERTICAL TXT.
- Page 26 5/16"-18UNC X 1.25" HHB (WZ) 011-0107038 1/2"-13UNC X 4.25" HHB (WZ) 011-0107030 1/2"-13UNC X 3.00" HHB (WZ) 011-0407024 1/2"-13UNC X 5.00" HHB (WZ) 010-01C0371 CABLE ASSEMBLY HD1610 - 205 3/16"LG. 026-STD-06-0329-BLK .4800" PLASTIC BUSHING 014-0015009 .375" E-CLIP 026-01PL2196 PLASTIC SCUFF GUARD 9.05" LG. 026-01PL2200...
-
Page 34: General Maintenance Information
Using your finger, press the grease into the ball-bearings and their tracks. repeat until the ball-bearing tracks are full of grease. Insert the shaft back into the bearing and wipe off excess grease. PLEASE KEEP THIS FOR YOUR RECORDS HD1610 ASSEMBLY PAGE 33... -
Page 35: Weight Training Tips
To be successful in your exercise program, it is important to develop an understanding of the basic principles of strength training. Now that you have your HD1610 HOIST® Fitness System, it is only natural that you want to get started immediately. First, determine a set of realistic goals and objectives for yourself. -
Page 36: Weight Ratios
OWNER'S MANUAL WEIGHT RATIOS The above chart shows the standard weight stack for this unit. The weights listed are approximate. HOIST reserves the right to modify the machine without prior notice. HD1610 ASSEMBLY PAGE 35... - Page 37 OWNER'S MANUAL HD1610 ASSEMBLY PAGE 36...
- Page 38 Hoist Fitness Systems warrants this product to the original purchaser to be free from defects in workmanship and/or materials under normal use or service. If at any time a component part is defective, Hoist Fitness Systems shall repair or replace it (at Hoist Fitness Systems option) within a reasonable period of time. This warranty does not cover costs of removal.
Need help?
Do you have a question about the HD1610 and is the answer not in the manual?
Questions and answers