Using My System; Control Organization; Programming My System - Radio Shack 8-IN-ONE REMOTE Owner's Manual

USING MY SYSTEM

The remote includes a custom My System mode for your devices.After the
MY SYSTEM key is programmed, it will allow you to access five groups of
remote control keys without having to change device modes. However, there
are some considerations.
• Keymoved, Learned, and Macro functions are affected by the My System
mode. If keys are moved (using Keymover) or learned onto (using
Learning) and they are placed on keys not within the Control Groups,
the keys will be ignored when pressed.
• A Macro on the POWER key (if applicable) will carry over to the My
System mode.
C O
ONTROL RGANIZATION
A C G
BOUT ONTROL ROUPS
For My System programming, the remote's keys are grouped by type of
control into the following five control groups:
(1) Playback Controls: REW, PLAY, FFWD, REC, STOP, and PAUSE
VOL+, VOL-, and MUTE
(2) Audio Controls:
(3) Channel Controls: CH+, CH-, Keypad (0 ~ 9), ENTER, LAST, SLEEP,
INFO, and TV/VIDEO
MENU, GUIDE, Cursor Controls (
(4) Menu Controls:
SELECT, and EXIT
(5) PIP Controls: PIP, FREEZE, SWAP, MOVE, and +100
A D G
BOUT EVICE ROUPS
Moreover, the remote's devices are grouped into the following five
device groups:
(1) Playback Group: VCR, CBL, SAT, CD, AUDIO, and DVD
(2) Audio Group: VCR, CBL, SAT, TV, CD, AUDIO, DVD and AUX
(3) Channel Group: VCR, CBL, SAT, TV, CD, AUDIO, DVD and AUX
(4) Menu Group: VCR, CBL, SAT, TV, and DVD
(5) PIP Group: VCR, CBL, SAT, and TV
The default Device Group settings from the factory is:
(1) Playback Group: VCR
(2) Audio Group: TV
(3) Channel Group: CBL
(4) Menu Group: CBL
TV
(5) PIP Group:
P
ROGRAMMING
For example, let's assume you have a TV, a cable converter, and a VCR in
your home theater system.You can program the My System mode so that
selected controls are assigned to these devices as follows:
1.
2.
(x 2)
3.
L M
, , , ),
M S
Y YSTEM
On the remote, press and hold P until the display changes
from the default device and time to [CODE SET].
NOTE: Default values for device, its code, and time are shown
above.Your remote control settings may be different.
NOTE: If you wish to exit the programming mode at any time, press
EXIT once. An [EXIT] message appears as the remote control returns
to normal operation.
NOTE: If an [INVALID] message appears, you have inadvertently
pressed an incorrect key. Simply note your error and continue
programming.
L
two times until [MY SYSTEM] appears.
Press
NOTE: If you go past [MY SYSTEM], press
return to it.
Press SELECT once to begin programming. [PLAYBACK]
appears.
NOTE: The program will automatically step through each Control
Group (from Playback to PIP) as you perform steps 3 through 7.
L M
However, you can use the or keys to navigate to a specific group
to make further changes.
a. Press SELECT once to enter Playback Control Group
assignment. The last-selected device (e.g., [TV]) appears.
b. Select a device for Playback Control Group assignment.
For this example, press VCR once. This will assign the
entire group of Playback Controls (i.e., REW, PLAY, FFWD,
REC, STOP, and PAUSE) to the VCR.Your device choice
(e.g., [VCR]) appears.
c. Press SELECT once to accept the assignment in step 3b.
The next Control Group assignment, [AUDIO]) appears.
U ' G
SER S UIDE
M
one or more times to
continued on next page...
Using My System 17