Related Manuals for WAGNER ProjectPro 117 0418B
Summary of Contents for WAGNER ProjectPro 117 0418B
- Page 1 Translation of the original operating instructions ProjectPro 117 Airless Sprayer 0418B Owner’s Manual...
- Page 2 Wagner Project Pro 117 - 0418B...
- Page 3 Wagner Project Pro 117 - 0418B SPRAY PRIME 25 - 30 cm 25 - 35 cm 25 - 30 cm 25 - 30 cm...
- Page 4 Wagner Project Pro 117 - 0418B...
- Page 5 Wagner Project Pro 117 - 0418B...
- Page 6 The operating instructions state that the following points must always be observed before starting up: 1. Faulty units must not be used. 2. Secure WAGNER spray gun using the safety catch on the trigger. 3. Ensure that the unit is properly earthed. The connection must take place through a correctly earthed two-pole and earth socket outlet.
-
Page 7: General Safety Instructions
Wagner Project Pro 117 - 0418B - Safety Information General Safety Instructions 3. Safety of Persons Read all the instructions. Non-observance of the instructions below Be attentive. Pay attention to what you are doing and work can cause electric shock, fire and or serious personal injuries. The sensibly with a power tool. -
Page 8: Explosion Protection
Wagner Project Pro 117 - 0418B - Safety Information Ventilation maintained badly. Good natural or artificial ventilation must be ensured in order to Use the power tool, accessories, insert tools, etc. in avoid the risk of explosion or fire and damage to health during spray accordance with these instructions and in a fashion work. -
Page 9: Components And Description
Wagner Project Pro 117 - 0418B Cleaning units with solvents When working outdoors: Vapors containing solvents may not be allowed to When cleaning the unit with solvents, the solvent blow toward the unit. should never be sprayed or pumped back into a Note the direction of the wind. -
Page 10: Field Of Application
Wagner Project Pro 117 - 0418B Field of application Figure 4 - Locking the Spray Gun Coating of interior walls as well as small and medium-sized objects Always lock the trigger off when attaching the spray outdoors (e.g. garden fences, garage doors, etc.). - Page 11 Wagner Project Pro 117 - 0418B 4. Slide the PressureTrac™ to its highest setting. The paint hose Keep hands clear from fluid stream. Ground the gun should stiffen as material begins to flow through it. by holding it against the edge of a metal container while flushing. Failure to do so may lead to a static 5. Unlock the spray gun.
- Page 12 Wagner Project Pro 117 - 0418B Figure 16 - Cleaning the Suction Set 3. Wrap the spray gun assembly in a damp cloth and place it in a plastic bag. Seal the bag shut. Place the sprayer in a safe 1. Lock the gun and turn the pump OFF (O). Turn the PRIME/ place out of the sun for short-term storage.
-
Page 13: Parts Lists
Wagner Project Pro 117 - 0418B Parts Lists Figure 19 - Suction set Part # Description Quantity 2306606 Suction set assembly ..........1 Figure 20 - Spray Gun/Spray Hose Item Part # Description Quantity 1 0418717 Gun assembly (without nozzle) ......1 2 0418708 Tip, L ................1... - Page 14 Wagner Project Pro 117 - 0418B Figure 21 - Pump section replacement instructions Kit Part Number 0418715 Always wear protective eye wear while servicing the pump. Be sure to follow the Pressure Relief Procedure when shutting the unit down for any purpose, including servicing or adjusting. After performing the Pressure Relief Procedure, be sure to unplug the unit before servicing or adjusting.
-
Page 15: Daily Maintenance
Wagner Project Pro 117 - 0418B - Troubleshooting / Maintenance Problem Cause Solution A. The sprayer does not start. The sprayer is not plugged in. Plug the sprayer in. 2. The ON/OFF switch is set to OFF. 2. Turn the ON/OFF switch to ON. 3. The sprayer was turned off while still under 3. Slide the PressureTrac™ to maximum pressure (+), or pressure. relieve pressure by turning the PRIME/SPRAY valve to PRIME. -
Page 16: Important Notes On Product Liability
If the check shows that the case is not a guarantee case, repairs are carried out at the expense of the buyer. Claims against Wagner that are based on or caused by the failure or insufficiency of a unit cannot be asserted. -
Page 17: Declaration Of Conformity
Wagner Project Pro 117 - 0418B Declaration of conformity Herewith we declare that the supplied version of WAGNER Project Pro 117 - 0418B Complies with the following provisons applying to it: 2006/42/EG, 2004/108/EG, 2002/95/EG, 2002/96/EG. Applied harmonized standards, in particular:... - Page 18 Wagner Project Pro 117 - 0418B Notes...
- Page 19 Wagner Project Pro 117 - 0418B Notes...
- Page 20 Wagner Project Pro 117 - 0418B J. Wagner GmbH E-Coreco s.r.o. Otto-Lilienthal-Str. 18 Na Roudné 102 D-88677 Markdorf 301 00 Plzen Hotline 0180/1000 227 +49/ (0) 75 44/ 505-1169 +420 739 359 518 +420 227 077 364 Wagner Spraytech Belgie J. Wagner Spraytech Ibérica S.A. Ctra. N-340, Km 1245,4 Veilinglaan 58 08750 Molins de Rei (Barcelona) 1861 Meise-Wolvertem +34/93/6 80 00 28 +34/93/6 68 01 56...