Related Manuals for WAGNER Control Stainer 150
Summary of Contents for WAGNER Control Stainer 150
- Page 1 ™ Owner‘s manual read this manual fOr cOmplete instructiOns franÇais - p. 13 espaÑOl - p. 25 wagner-group.com watch a video manual at www.wagnerspraytech.com/controlstainer150 0117 • Form No. 0529650B...
-
Page 2: Table Of Contents
iMPortant saFetY inForMation taBle oF contents GroUnDinG instrUctions IMPORTANT SAFETY INFORMATION ..........2-3 This product must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by CONTROLS AND FUNCTIONS ............4-5 providing an escape wire for the electric current. This product SETUP ...................... -
Page 3: Important Safety Information
iMPortant saFetY inForMation saFetY hazarDs HAZARD: EXPLOSION OR FIRE HAZARD: gENERAL Flammable vapors, such as solvent and This product can cause severe injury or property paint vapors, in work area can ignite or damage. explode. PREVENTION: PREVENTION: • Always wear appropriate gloves, eye protection, clothing •... -
Page 4: Controls And Functions
controls anD FUnctions Nozzle Turbine Seal Air cap Filter housing ON/OFF switch Nozzle assembly Filter Kickstand Material flow Seal control Trigger Pickup tube Material container (600 ml) -
Page 5: Controls And Functions
controls anD FUnctions on / oFF switch The ON/ OFF switch turns the turbine ON (I) and OFF (0). No spray material will be delivered until trigger is pulled. Material Flow control The material flow control knob determines the amount of spray material that is sprayed from the spray nozzle. -
Page 6: Setup
setUP For a video showing how to set up the Control Stainer, visit: www.wagnerspraytech.com/controlstainer150 Material PreParation Material to be sprayed may need to be strained to remove any impurities in the paint which may enter and clog the system. Impurities in the paint will give poor performance and a poor finish. - Page 7 setUP For a video showing how to set up the Control Stainer, visit: www.wagnerspraytech.com/controlstainer150 asseMBlY NEVER point the spray gun at any part of the body. Make sure the power cord is unplugged. Stir the spraying material thoroughly. Fill the container. Use a strainer to remove any particles. (see Thinning the Material, previous page, if thinning is required).
-
Page 8: Sprayer Controls
For a video showing Control Stainer 150 spraying tips and best practices, visit: www.wagnerspraytech.com/controlstainer150 Material Flow control The material flow control will be factory-set at its lowest setting out of the box. Adjust as needed. • Turn the knob out (counterclockwise) for less flow. -
Page 9: Spraying
For a video showing Control Stainer 150 spraying tips and best practices, visit: www.wagnerspraytech.com/controlstainer150 how to sPraY ProPerlY Even coat throughout • Turn the ON/OFF switch to ON (I) to turn on the turbine. Correct 3 to 6 inches No material will spray until the trigger is activated. -
Page 10: Cleanup
cleanUP For a video showing cleanup of the Control Stainer150, visit: www.wagnerspraytech.com/controlstainer150 cleanUP notes When cleaning, use the appropriate cleaning solution (warm, soapy water for water-based coatings, and mineral spirits for oil-based coatings. Special cleanup instructions for use with flammable solvents (must have a flashpoint above 100ºF (38ºC): •... -
Page 11: Maintenance
Maintenance cleaninG the Filter Press IMPORTANT: Before every use, you should inspect the air filter in the turbine to see if it is excessively dirty. If it is dirty, follow these steps to replace it. Never operate your unit without the air filters. -
Page 12: Troubleshooting
troUBleshootinG ProBleM caUse solUtion Problem A: Little or no material flow 1. Nozzle clogged. 1. Clean. 2. Suction tube clogged. 2. Clean. 3. Material flow setting too low. 3. Increase material flow setting. 4. Suction tube loose. 4. Remove and replace as tightly as possible. 5. -
Page 13: Parts List
Parts List • Liste de Pièces • Lista de Piezas Replacement parts available by calling customer service On peut obtenir des pièces de rechange en appelant le Service à la clientèle. Los repuestos están disponibles llamanado al servicio a clientes. 1-800-328-8251 Part No. - Page 14 Parts List • Liste de Pièces • Lista de Piezas Part No. English Français Español Qty. Nº de piéce Description Description Descripción Qte. Pieza No. cant. 0529276 Nozzle assembly (includes Ensemble de buse (inclut des Ensamblaje de boquilla items 1-9) pièces 1 à...
-
Page 15: Warranty
Este producto, fabricado por la Wagner Spray Tech Corporation (Wagner), está garantizado contra defectos de materiales y de mano de obra por un año a partir de la fecha de compra siempre y cuando se utilice de acuerdo con las recomendaciones e intrucciones impresas de Wagner. Esta garantía no cubre daños ocasionados por el uso incorrecto, accidentes, negligencia por parte del usario o el desgaste normal. - Page 16 ™ wagner-group.com...