Audible User Feedback Tones - Kenwood TK-8102H Service Manual

TK-8102H
Off hook decode
If the Off hook decode function has been enabled, re-
moving and replacing the microphone on the hook has no
effect for decoding QT/DQT and option signalling.
"TOT" pre-alert
The transceiver has "TOT" pre-alert timer. This param-
eter selects the time at which the transceiver generates
"TOT" pre-alert tone before "TOT" is expired.
"TOT" will be expired when the selected time passes
from a TOT pre-alert tone.
"TOT" re-key time
The transceiver has "TOT" re-key timer. This timer is the
time you can not transmit after "TOT" exceeded. After
"TOT" re-key time expired you can transmit again.
"TOT" reset time
The transceiver has "TOT" reset timer. This timer is the
minimum wait time allowed during a transmission that will
reset the "TOT" count.
"TOT" reset time causes the "TOT" to continue even
after PTT is released unless the "TOT" reset timer has ex-
pired.
Clear to transpond
The transceiver waits the transpond of DTMF if channel
is busy until channel open. This feature prevents the inter-
ference to other party.
6. Option Signalling (DTMF)
Built-in DTMF decoder is available for option signalling.
It is possible to use individual call, group call, Stun.
If the option signalling matches, a predetermined action
will occur.
If option signalling matches on a channel is set up with
option signalling, the channel LED will flash and option sig-
nalling will be released. The transpond or alert tone will
sound.
While option signalling matches (or if option signalling is
deactivated when you are transmitting), you can mute or
unmute QT/DQT/Carrier.
SP Unmute
You can select the type of SP Unmute system for each
channel. The selection is as follows.
Carrier, QT/DQT:
Channel with this option will not check ID Code in order
to open its speaker.
Carrier+DTMF, QT/DQT+DTMF:
Channel that is set with this option will have to check for
ID Code in order to open its speaker.
Default:
Carrier, QT/DQT.
6
OPERATING FEATURES
SP unmute
Carrier
Carrier+DTMF
QT/DQT
QT/DQT+DTMF
Note :
can not be selected.
DQT+DTMF can not be selected.
signalling, option signalling is released. After matching op-
tion signalling, option signalling will temporarily reset auto-
matically.
cur. Whether option signalling is activated or not, when
stun matches on any channel, the transceiver will become
TX inhibited or TX/RX inhibited. While stun is active, if the
stun code + "#" code is received, stun will deactivate.
not be output.

7. Audible User Feedback Tones

notify the user of the transceiver operating state.
tions that are not listed below.
sounds.
Channel setting RX condition
QT/DQT DTMF
None None Carrier
Yes Carrier
Carrier+DTMF
None Yes Carrier
Carrier+DTMF
Yes None Carrier
Carrier+QT/DQT
Yes Carrier
Carrier+QT/DQT
Carrier+QT/DQT+DTMF
Carrier+DTMF
Yes Yes Carrier
Carrier+QT/DQT
Carrier+QT/DQT+DTMF
Carrier+DTMF
When QT/DQT is not used, QT/DQT and QT/DQT+DTMF
When DTMF is not used, Carrier+DTMF and QT/
Auto Reset
If option signalling matches a group set up with option
Stun
If the stun code matches, a predetermined action will oc-
When stun matches, transpond will function. Alert will
The transceiver outputs various combinations of tones to
Refer to the help file on the KPG-70D, regarding the func-
Stun on tone
When a stun code is received, transpond tone sounds.
Stun off tone
When a stun release code is received, transpond tone
Speaker
condition
Sounds
Sounds
Sounds
Not Sounds
Sounds
Not Sounds
Sounds
Not Sounds
Sounds
Sounds
Not Sounds
Not Sounds
Not Sounds
Sounds
Not Sounds