Panasonic CQ-VD7001W Operating Instructions Manual page 20

Settings
(continued)
(AUDIO continued)
SP SETUP
(Speaker set up)
Setting the absence/presence and size of each speaker
FRONT (Front speaker setting)
LARGE : for large speakers, when bass playback is
possible (at least 100 Hz or lower)
: for small speakers, or when bass playback is
SMALL
not possible
default:
CENTER
(Center speaker setting)
LARGE : for large speakers, when bass playback is
possible (at least 100 Hz or lower)
SMALL : for small speakers, or when bass playback is
not possible
NONE : when not using a center speaker
default:
* A center speaker (option, EAB-CF2 recommended) is
required.
SURROUND
(Surround speaker setting)
LARGE : for large speakers, when bass playback is
possible (at least 100 Hz or lower)
SMALL : for small speakers, or when bass playback is
not possible
NONE : when not using a surround speaker
default:
SUB - W (Subwoofer speaker setting)
YES : when using a subwoofer
NO : when not using a subwoofer
default:
* A subwoofer (option, CJ-HD303N recommended) is
required. A power amplifier (option) is also required for
connecting a subwoofer.
Note:
¡While the private mode is active, only
FRONT
adjusted.
: Previous menu
[MENU] [MODE]
: Previous menu
40
CQ-VD7001W
SP LEVEL
(Speaker level)
Adjusting the output balance of each speaker
(Left front speaker output bal-
FRONT L
ance)
] [
: down, : up
CENTER (Center speaker output balance)
] [
: down, : up
LARGE
(Right front speaker output bal-
FRONT R
ance)
] [
: down, : up
(Right surround speaker output
R SURROUND
¡
balance)
] [
: down, : up
(Left surround speaker output
L SURROUND
¡
balance)
NONE
] [
: down, : up
(Subwoofer speaker output bal-
SUB - W
ance)
] [
: down, : up
Setting range: –10 dB to +10 dB (1 dB steps)
default: ± 0 dB for all speakers
A test signal (a continuous tone) is output from each
speaker for approximately 2 seconds.
Adjust the output balance so that the tone appears to have
the same volume from each speaker.
LARGE
Adjusting the output balance:
Adjust the volume of all of the other speakers to the volume
level of the speaker from which the test signal appears to be
the quietest.
¡If the speaker setting is (none) or
NONE
speaker, the test signal is not output and that speaker
cannot be selected.
¡ Turn rotary volume controller or press [}] or [{]
NO
(VOL) to adjust the volume of the test signal.
Note:
¡While the private
mode is active, only
can be
adjusted.
: Quit : Select/adjust
[ENTER]
: Quit []] [[] [}] [{]
: Select/adjust
SP DELAY
Adjusting the timing with which the audio from each speak-
er reaches the listener's position
CENTER
]
: down,
SURROUND
]
: down,
¡Make this adjustment while listening to sound.
¡If the speaker setting is
speaker cannot be selected.
¡When "PRO LOGIC" is displayed, 15 ms are automatically
added to the delay time setting for the surround speakers.
MODE LEVEL
Setting the VTR/AUX input level
Make this setting if it is not possible to adjust the volume
through the connected device (on the output side).
VTR LEVEL
: sets the level low/sound volume increases
LOW
HIGH : sets the level high/sound volume decreases
(no) for a AUX LEVEL
NO
LOW : sets the level low/sound volume increases
HIGH : sets the level high/sound volume decreases
Note:
¡If the input level from VTR/AUX is too high, the audio will
not be output normally.
¡After setting the input level
and
FRONT L
The volume can be adjusted by pressing [}] or [{]
can be
FRONT R
(VOL) on the remote control or turning rotary volume
controller on the unit.
[MENU]
: Determine
LPF/HPF
(Speaker delay)
Cut off frequency
LPF CUT OFF
(Center speaker delay time set-
ting)
]
: down,
[
: up
Setting range: 0 ms to 5 ms (1 ms steps)
1 ms = 0.001 seconds
default: 0 ms
HPF CUT OFF
(Surround speaker delay time
]
setting) : down,
[
: up
Setting range: 0 ms to 15 ms (1 ms steps)
1 ms = 0.001 seconds
default: 0 ms
Note:
¡This setting is not available if
(none) for a speaker, that set to
NONE
¡
HPF CUT OFF
front speakers (L/R) and rear speakers (L/R).
(Setting for VTR)
default:
HIGH
(Setting for AUX)
default:
HIGH
: Previous menu : Quit
[MODE]
: Previous menu : Quit []] [[] [}] [{]
(Low Pass Filter/High Pass Filter)
(Sub-woofer Low Pass Filter)
[
: up
Setting range: 60 Hz to 160 Hz (in 5 Hz step)
default: 100 Hz
(High Pass Filter)
[
: up
Setting range: off, 90 Hz to 225 Hz (in 5 Hz step)
default: off
(SRS setting) is
CS Auto
(on).
ON
(High pass filter) is enabled only on the
: Select/adjust
[ENTER]
: Select/adjust : Determine
41
CQ-VD7001W