Panasonic CQ-VD7001W Operating Instructions Manual page 18

Settings
(continued)
USER
SCREEN AUDIO DVD INPUT/OUTPUT
DISPLAY UNIT
Display adjustment
TILT
(Tilt angle adjustment)
1 2 3 4 5
1
default:
OPEN/CLOSE
(Monitor setting when power on)
AUTO
: the monitor is opened automatically when
turning ON ACC.
MANUAL
: the monitor is not opened automatically.
default:
Note:
¡The monitor position setting menu can also be displayed
by pressing the [TILT] button on the display unit for
more than 2 seconds. (a page 17)
CLOCK
Clock setting
DISPLAY
(Clock display)
OFF : clock display OFF
ON
: clock display ON ("0:00" is displayed
before adjusting the clock.)
default:
HOUR ADJUST
(Hour adjustment)
]
: puts back hour
[
: puts forward hour
MINUTE ADJUST
(Minute adjustment)
]
: puts back minute
[
: puts forward minute
: Previous menu
[MENU] [MODE]
: Previous menu
36
CQ-VD7001W
RADIO
Note:
¡To start the clock, touch/press
¡Set the Daylight Saving Time manually.
default: HOUR ADJUST: 0
5
TOUCH PANEL
Panel touch position adjustment
5
Position difference between the touching position and the
displaying symbol position may appear in the following sit-
uations:
1. The display position adjustment is executed.
2. The system is initialized.
3. The power is turned off soon after the touch panel is
adjusted.
For the cases above, readjust the touch panel position.
MANUAL
Note:
¡ This function can be performed on the touch panel.
This function is used only when there are some differ-
ences between the touching position and the symbol
position displayed on the monitor.
This function is not used ordinarily.
q Select (yes) to proceed.
YES
OFF
w Touch the four corners of the touch panel counterclock-
wise.
e Touch (yes) to reflect. To quit, touch
YES
(no).
r Touch fourth e Touch third
q Touch first w Touch second
: Quit : Select/adjust
[ENTER]
: Quit []] [[] [}] [{]
: Select/adjust
ID-CODE
/ [MODE].
ID Code Setting
Prior to operating this unit, it is advisable to assign a 4-
digit ID code for security. Once the ID code has been set,
MINUTE ADJUST: 0
the unit cannot be operated if the main power supply is dis-
connected then re-connected. It is electronically locked so
that a thief cannot use the stolen unit unless that person
knows the code you have set.
The ID code operation must be performed only by the per-
son to whom the unit belongs.
Generally, it is not necessary to enter the ID code each
time when using the unit if it has not been disconnected
from the main power supply (car battery).
0 9
to 4 digits numeric code
How to set your ID code (for the first time)
q Enter an 4 digit ID code.
w Enter the same 4 digit ID code again.
How to change your ID code
q Enter the preset (old) 4 digit ID code. If the wrong ID code
is entered, a new ID code cannot be registered.
w Enter a new 4 digit ID code.
e Enter the new 4 digit ID code again.
How to cancel the known ID code
q Enter the preset (old) 4 digit ID code. If the wrong ID code
is entered, it is not possible to cancel the ID code function.
w Touch/press and hold
"Complete!" is displayed. The ID code cancelling proce-
dure is completed. The unit now works without an ID code.
Note:
¡ Should your unit ever require service, cancel your ID code
before sending for repair.
NO
¡ The ID code setting cannot be eliminated even by the
memory clear function.
¡ The inputted code is not displayed for your security.
Caution
¡Record your registered ID code and keep it in a secure
location. If you forget it, you will be unable to use the
unit. In case you forget the ID code, please consult
your nearest Panasonic Service Center.
[MENU]
: Determine
MEMORY CLEAR
Memory clearance
The state of all of the current memories are returned to
default settings.
Note:
¡The ID code is not deleted by executing memory clear.
NO
YES
default: none
CANCEL
OK
Caution
¡Be aware that this setting restores the unit to default
settings, so that all the memories and settings that
you have set will be eliminated.
OTHER
/ [ENTER] until
Other settings
BEEP
OFF
ON
MENU DISPLAY
ENGLISH
CHINESE
: Previous menu : Quit
: Previous menu [MODE] : Quit
[]] [[] [}] [{]
: no memory clear.
The display returns to the previous one.
: clears the memory to default settings
default:
NO
(really?) appears
REALLY?
when is selected.
YES
: no memory clear.
: Proceed.
(Beep setting)
: operation sound (beep) OFF
: operation sound (beep) ON
default:
ON
(Language setting)
: displays the menu in English
: displays the menu in Chinese
default:
ENGLISH
: ID code deletion
: Select/adjust
ID code deletion
[ENTER]
: Select/adjust :
Determine
37
CQ-VD7001W